REAR SPOILER INSTALLATION


  1. PRECAUTION

    Note


    • If a rear spoiler sub-assembly is removed and installed, the location of the axis of the rear wiper motor assembly (for Glass Hatch Type) will change, causing the wiping angle to change. Be sure to remove and install the rear wiper motor assembly (for Glass Hatch Type) using the centering jig.

    • After installing a rear spoiler sub-assembly, install the rear wiper motor assembly (for Glass Hatch Type), do not open the glass hatch and the back door before installing the rear wiper link pivot.

  2. INSTALL CENTER STOP LIGHT ASSEMBLY (for Rear Spoiler without Press Line)


    1. Connect the connector.

    2. Connect the center stop light assembly to the rear spoiler sub-assembly.

    3. A017EI8

      Install the center stop light assembly with the 2 screws.

  3. INSTALL REAR WASHER NOZZLE (for Rear Spoiler without Press Line)


    1. A017G0C

      Engage the claws and install the rear washer nozzle.

    2. A017C32

      Install the rear washer nozzle bracket with the screw.

  4. INSTALL CENTER STOP LIGHT ASSEMBLY (for Rear Spoiler with Press Line)


    1. Connect the connector.

    2. Connect the center stop light assembly to the rear spoiler sub-assembly.

    3. A017C1N

      Install the center stop light assembly with the 2 screws.

  5. INSTALL REAR WASHER NOZZLE (for Rear Spoiler with Press Line)


    1. A017BLY

      Engage the claws and install the rear washer nozzle.

    2. A017EEB

      Install the rear washer nozzle bracket with the screw.

  6. INSTALL REAR SPOILER SUB-ASSEMBLY


    1. A017D23

      Raise and lower the glass hatch and the back door respectively. Pass the wire harness into the vehicle and temporarily install the rear spoiler sub-assembly.

    2. Engage the 2 claws.

      A017EPG

    3. Temporarily install the 8 screws.

      A017E0HE01

    4. Using a "TORX" socket wrench (T30), fully tighten the 6 screws (B).

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

    5. Using a "TORX" socket wrench (T30), fully tighten the 2 screws (A).

      Torque:
      6.5 N*m  { 66 kgf*cm, 58 in.*lbf }

    6. Connect the wire harness.


      1. A017E9T

        Connect the connector.

      2. Engage the grommet.

      3. A017EDG

        Connect the rear washer hose.

      4. Connect the 2 connectors.

      5. A017CUT

        Install the wire harness grommet to the wire harness.

      6. Engage the 4 claws and install the wire harness.

  7. INSTALL BACK DOOR GLASS GUIDE BRACKET SUB-ASSEMBLY (for Fixed Glass Type)


    1. A017CE4

      Engage the clip and install the back door glass guide bracket sub-assembly.

    2. A017D4LE01

      Install the 3 bolts <B>.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    3. Tighten the bolt <A>.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

  8. INSTALL REAR WIPER MOTOR ASSEMBLY (for Fixed Glass Type)


    1. A017COW

      Install the rear wiper motor assembly with the 4 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      Note

      Be careful not to scratch the back door glass.

    2. Connect the connector.

  9. INSTALL REAR WIPER MOTOR ASSEMBLY (for Glass Hatch Type)


    1. A017CCBE01

      Temporarily install the rear wiper motor assembly with the 4 bolts and 2 nuts.

      Note


      • Do not hold the rear wiper motor assembly by the rear wiper link pivot.

      • Be careful not to scratch the back door glass.

      • Do not remove the centering jig before installing the rear wiper link pivot.

    2. Tighten the 4 bolts and 2 nuts in the order shown in the illustration to install the rear wiper motor assembly.

      Torque:
      Bolt
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
      Nut
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    3. Connect the connector.

  10. INSTALL REAR WIPER MOTOR GROMMET (for Fixed Glass Type)


    1. A017E3TE01

      Apply MP grease to the entire surface of the wiper motor grommet lip.

      Tech Tips

      Make sure that the hole does not clog with grease and the grooves on the lip are filled with grease.

    2. A017B35E02

      Install the rear wiper motor grommet.

      Tech Tips

      As shown in the illustration, install the rear wiper motor grommet with its position mark at the top.

  11. INSTALL REAR WIPER LINK PIVOT (for Glass Hatch Type)


    1. A017CYL

      Install the rear wiper link pivot with the nut.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

    2. Open the glass hatch.

    3. A017B51

      Disengage the 2 guides.

    4. Disengage the 3 claws and remove the centering jig.

    5. Close the glass hatch.

  12. INSTALL REAR WIPER LINK CAP (for Glass Hatch Type)


    1. A017FA7E01

      Apply MP grease to the entire surface of the rear wiper link cap.

      Tech Tips

      Make sure that the hole does not get clogged with grease and the grooves on the lip are filled with grease.

    2. A017ESU

      Install the rear wiper link cap.

  13. INSTALL REAR WIPER ARM AND BLADE ASSEMBLY (for Fixed Glass Type)


    1. Stop the wiper motor at the automatic stop position.

    2. A017C5CE01

      When reinstalling:


      1. Clean the wiper arm serrations.

      2. Clean the wiper pivot serrations with a wire brush.

    3. A017DRZE02

      Place the rear wiper arm and blade assembly so that the rear wiper blade is aligned with the ceramic line.

      Area Dimension
      A 10 mm (0.39 in.)

    4. Install the rear wiper arm and blade assembly with the nut.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      Tech Tips

      Hold down the wiper arm by hand when tightening the nut.

  14. INSTALL REAR WIPER ARM AND BLADE ASSEMBLY (for Glass Hatch Type)


    1. Stop the wiper motor at the automatic stop position.

    2. A017C5CE01

      When reinstalling:


      1. Clean the wiper arm serrations.

      2. Clean the wiper pivot serrations with a wire brush.

    3. A017BKPE01

      Place the rear wiper arm and blade assembly so that the rear wiper blade is aligned with the ceramic line.

      Area Dimension
      A 10 mm (0.39 in.)

    4. Install the rear wiper arm and blade assembly with the nut.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      Tech Tips

      Hold down the wiper arm by hand when tightening the nut.

  15. INSTALL REAR WIPER ARM HEAD CAP


    1. A017DOH

      Install the rear wiper arm head cap.

      Tech Tips

      Push down on the cap until a click sound can be heard.

  16. INSTALL REAR WIPER SHAFT COVER (for Glass Hatch Type)


    1. Open the glass hatch.

    2. A017G4Z

      Engage the 3 clips and install the rear wiper shaft cover.

    3. Operate the rear wiper while spraying washer fluid on the glass. Make sure that the rear wiper functions properly and there is no interference with the vehicle body.

  17. INSTALL BACK DOOR TRIM PANEL ASSEMBLY


    1. A017CKT

      Engage the 16 clips and install the back door trim panel assembly.

  18. INSTALL ASSIST STRAP ASSEMBLY


    1. A017FJZ

      Install the assist strap assembly with the bolt.

  19. INSTALL ASSIST STRAP HOLE COVER


    1. A017CPS

      Engage the 2 guides and 2 claws, and install the assist strap hole cover.

  20. INSTALL BACK DOOR LOCK COVER (for Glass Hatch Type)


    1. A017G02

      Engage the 4 guides and 2 claws, and install the back door lock cover.

  21. INSTALL BACK DOOR TRIM COVER LH (w/o Power Back Door)


    1. A017BOQ

      Engage the 2 clips and 2 claws, and install the back door trim cover LH.

  22. INSTALL BACK DOOR TRIM COVER LH (w/ Power Back Door)


    1. A017ERC

      Engage the 2 clips and 2 claws, and install the back door trim cover LH.

  23. CONNECT POWER BACK DOOR ROD (w/ Power Back Door)


    1. A017F50

      Install the back door stay plate and connect the power back door rod.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

  24. INSTALL BACK DOOR SERVICE HOLE COVER LH (w/ Power Back Door)


    1. A017ECX

      Engage the 6 claws and install the back door service hole cover LH.

  25. INSTALL BACK DOOR TRIM COVER RH


    1. A017D6U

      Engage the 2 clips and 2 claws, and install the back door trim cover RH.

  26. INSTALL BACK WINDOW UPPER TRIM PANEL ASSEMBLY


    1. A017EYI

      Engage the 4 clips and 4 claws, and install the back window upper trim panel assembly.

  27. INSPECT REAR WASHER NOZZLE


    1. With the engine running, check the position that the washer fluid hits the windshield.

      A017B32E01
      Area Dimension Area Dimension
      A 265 mm (10.44 in.) E 252 mm (9.92 in.)
      B 197 mm (7.77 in.) F 178 mm (7.00 in.)
      C 0.4 mm (0.01 in.) G 25 mm (0.98 in.)
      D 109 mm (4.27 in.) H 139 mm (5.46 in.)
      OK
      Washer fluid hits the windshield in the areas shown in the illustration.