REAR SPOILER REMOVAL


  1. PRECAUTION

    Note

    If a rear spoiler sub-assembly is removed and installed, the location of the axis of the rear wiper motor assembly (for Glass Hatch Type) will change, causing the wiping angle to change. Be sure to remove and install the rear wiper motor assembly (for Glass Hatch Type) using the centering jig.

  2. REMOVE BACK WINDOW UPPER TRIM PANEL ASSEMBLY


    1. A017EYI

      Disengage the 4 clips and 4 claws, and remove the back window upper trim panel assembly.

  3. REMOVE BACK DOOR TRIM COVER LH (w/o Power Back Door)


    1. A017BOQ

      Disengage the 2 clips and 2 claws, and remove the back door trim cover LH.

  4. REMOVE BACK DOOR SERVICE HOLE COVER LH (w/ Power Back Door)


    1. A017ECX

      Disengage the 6 claws, and remove the back door service hole cover LH.

  5. DISCONNECT POWER BACK DOOR ROD (w/ Power Back Door)


    1. A017F50

      Disconnect the power back door rod and remove the back door stay plate.

  6. REMOVE BACK DOOR TRIM COVER LH (w/ Power Back Door)


    1. A017ERC

      Disengage the 2 clips and 2 claws, and remove the back door trim cover LH.

  7. REMOVE BACK DOOR TRIM COVER RH


    1. A017D6U

      Disengage the 2 clips and 2 claws, and remove the back door trim cover RH.

  8. REMOVE BACK DOOR LOCK COVER (for Glass Hatch Type)


    1. A017G02

      Disengage the 2 claws and 4 guides, and remove the back door lock cover.

  9. REMOVE ASSIST STRAP HOLE COVER


    1. A017CPS

      Disengage the 2 claws and 2 guides, and remove the assist strap hole cover.

  10. REMOVE ASSIST STRAP ASSEMBLY


    1. A017FJZ

      Remove the bolt and assist strap assembly.

  11. REMOVE BACK DOOR TRIM PANEL ASSEMBLY


    1. A017CKT

      Disengage the 16 clips and remove the back door trim panel assembly.

  12. REMOVE REAR WIPER SHAFT COVER (for Glass Hatch Type)


    1. A017G4Z

      Disengage the 3 clips and remove the rear wiper shaft cover.

  13. REMOVE REAR WIPER ARM HEAD CAP


    1. A017DOH

      Remove the rear wiper arm head cap.

  14. REMOVE REAR WIPER ARM AND BLADE ASSEMBLY


    1. A017BYQ

      Remove the nut and the rear wiper arm and blade assembly.

  15. REMOVE REAR WIPER LINK CAP (for Glass Hatch Type)


    1. A017ESU

      Remove the rear wiper link cap.

  16. REMOVE REAR WIPER MOTOR GROMMET (for Fixed Glass Type)


    1. A017DID

      Remove the rear wiper motor grommet.

  17. REMOVE REAR WIPER LINK PIVOT (for Glass Hatch Type)


    1. A017CYL

      Remove the nut and the rear wiper link pivot.

  18. REMOVE REAR WIPER MOTOR ASSEMBLY (for Fixed Glass Type)


    1. A017COW

      Disconnect the connector.

    2. Remove the 4 bolts and the rear wiper motor assembly.

      Note

      Be careful not to scratch the back door glass.

  19. REMOVE REAR WIPER MOTOR ASSEMBLY (for Glass Hatch Type)


    1. When reinstalling the rear wiper motor assembly:


      1. Open the glass hatch.

      2. A017B51

        Engage the 3 claws and 2 guides, and then install the centering jig.

        Note


        • The centering jig cannot be reused.

        • Do not remove the centering jig before installing the rear wiper link pivot.

      3. A017EGY

        Close the glass hatch, and engage the 2 claws and guide.

        Note

        Be sure to engage the 2 claws and guide securely.

      4. A017CCB

        Disconnect the connector.

      5. Remove the 2 nuts.

      6. Remove the 4 bolts and the rear wiper motor assembly.

        Note


        • Do not hold the rear wiper motor assembly by the rear wiper link pivot.

        • Be careful not to scratch the back door glass.

    2. When using a new rear wiper motor assembly:


      1. A017ET9

        Disconnect the connector.

      2. Remove the 4 bolts.

      3. A017FDH

        Remove the 2 nuts and the rear wiper motor assembly.

        Note

        Be careful not to scratch the back door glass.

  20. REMOVE BACK DOOR GLASS GUIDE BRACKET SUB-ASSEMBLY (for Fixed Glass Type)


    1. A017D4LE01

      Loosen the bolt <A>.

      Note

      Bolt <A> cannot be removed from the back door glass guide bracket sub-assembly.

    2. Remove the 3 bolts <B>.

    3. A017CE4

      Disengage the clip and remove the back door glass guide bracket sub-assembly.

  21. REMOVE REAR SPOILER SUB-ASSEMBLY


    1. A017B1AE01

      Put protective tape around the rear spoiler sub-assembly.

    2. Disconnect the wire harness.

      Note

      Do not allow the disconnected wire harness to get caught between the back door and the vehicle body to prevent it from being damaged.


      1. A017C3J

        Turn back the wire harness grommet.

      2. Disengage the 4 claws and pull out the wire harness from the vehicle.

        Note

        Do not forcefully pull out the wire harness.

      3. A017EDG

        Disconnect the 2 connectors.

      4. Disconnect the rear washer hose.

      5. A017E9T

        Disengage the grommet.

      6. Disconnect the connector.

    3. Using a "TORX" socket wrench (T30), remove the 2 screws (A).

    4. Using a "TORX" socket wrench (T30), remove the 6 screws (B).

      A017E0HE01

    5. Disengage the 2 claws.

      A017EPG
    6. A017D23

      Raise and lower the glass hatch and the back door respectively. Pull out the wire harness from the vehicle and remove the rear spoiler sub-assembly.

  22. REMOVE REAR WASHER NOZZLE (for Rear Spoiler without Press Line)


    1. A017C32

      Remove the screw and rear washer nozzle bracket.

    2. A017G0C

      Disengage the claws and remove the rear washer nozzle.

  23. REMOVE CENTER STOP LIGHT ASSEMBLY (for Rear Spoiler without Press Line)


    1. A017EI8

      Remove the 2 screws.

    2. Disconnect the center stop light assembly from the rear spoiler sub-assembly.

    3. Disconnect the connector and remove the center stop light assembly.

  24. REMOVE REAR WASHER NOZZLE (for Rear Spoiler with Press Line)


    1. A017EEB

      Remove the screw and rear washer nozzle bracket.

    2. A017BLY

      Disengage the claws and remove the rear washer nozzle.

  25. REMOVE CENTER STOP LIGHT ASSEMBLY (for Rear Spoiler with Press Line)


    1. A017C1N

      Remove the 2 screws.

    2. Disconnect the center stop light assembly from the rear spoiler sub-assembly.

    3. Disconnect the connector and remove the center stop light assembly.