Click here

REAR DOOR DISASSEMBLY

Click here
Click here
  1. Click here

    DISCONNECT NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait for 90 seconds after disconnecting the terminal to prevent airbag deployment (Click here).

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  2. Click here

    REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. A017F1XE01

      Using a screwdriver with the tip wrapped with protective tape, disengage the 3 claws and remove the rear door inside handle bezel plug.

  3. Click here

    REMOVE REAR DOOR ARMREST UPPER BASE PANEL


    1. A017EWNE01

      Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws and 2 clips, and remove the rear door armrest upper base panel.

    2. Disconnect the connector.

  4. Click here

    REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY


    1. A017FQH

      Disengage the 2 claws and remove the rear power window regulator switch assembly.

  5. Click here

    REMOVE DOOR ASSIST GRIP COVER


    1. A017D3PE01

      Using a screwdriver with the tip wrapped with protective tape, disengage the 4 claws and remove the door assist grip cover.

  6. Click here

    REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. A017F2K

      Remove the 3 screws.

    2. A017GAC

      Using a clip remover, disengage the 9 clips.

    3. Disengage the 5 claws and separate the rear door trim board sub-assembly from the rear door inner glass weatherstrip.

    4. A017EA4

      Disengage the 2 clamps.

    5. Disconnect the front door lock remote control cable and rear door inside locking cable.

  7. Click here

    REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


    1. A017BNY

      Remove the 2 screws.

    2. Disengage the 2 claws and disconnect the rear door inside handle sub-assembly.

  8. Click here

    REMOVE REAR SPEAKER ASSEMBLY


    1. A017ESY

      Disconnect the connector.

    2. Remove the 3 bolts and rear speaker assembly.

      Note:

      Do not touch the cone part of the speaker.

  9. Click here

    REMOVE REAR DOOR INNER GLASS WEATHERSTRIP


    1. A017B79

      Remove the rear door inner glass weatherstrip from the rear door panel.

  10. Click here

    REMOVE REAR DOOR SERVICE HOLE COVER


    1. A017D47

      Disconnect the connector.

    2. Remove the rear door service hole cover.

      Tip:

      Remove the remaining tape on the door.

  11. Click here

    REMOVE REAR DOOR CHECK ASSEMBLY


    1. A017EAN

      Remove the bolt, 2 nuts, and the rear door check assembly.

  12. Click here

    REMOVE REAR DOOR WEATHERSTRIP


    1. A017B9B

      Using a clip remover, disengage the 19 clips and remove the rear door weatherstrip.

  13. Click here

    REMOVE REAR DOOR GLASS RUN


    1. A017BMF

      Remove the rear door glass run.

  14. Click here

    REMOVE REAR DOOR FRAME GARNISH


    1. A017EXJ

      Disengage the clip and remove the rear door frame garnish.

      Tip:

      This clip needs to be replaced with a new one because the clip will break when removing the rear door frame garnish.

  15. Click here

    REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    1. A017FHT

      Remove the rear door vent seal.

    2. A017ECI

      Remove the 2 bolts, screw, and the rear door window division bar sub-assembly.

  16. Click here

    REMOVE REAR DOOR QUARTER WINDOW GLASS


    1. A017E81

      Remove the rear door quarter window glass and the rear door quarter window weatherstrip as a unit as shown in the illustration.

    2. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.

  17. Click here

    REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    1. A017F6A

      Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

      Note:

      Do not damage the door glass.

  18. Click here

    REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY


    1. A017B2YE01

      Disconnect the connector.

    2. Loosen the temporary bolt.

      Note:

      Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator may fall and cause damage.

    3. Remove the 3 bolts.

    4. Remove the rear door window regulator sub-assembly and the rear power window regulator motor assembly as a unit.

    5. Remove the temporary bolt from the rear door window regulator sub-assembly.

  19. Click here

    REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY


    1. A017C3NE01

      Connect the positive (+) lead of the battery to terminal 2, and the negative (-) lead to terminal 1 of the rear power window regulator motor assembly to move the lift arm to the position shown in the illustration.

    2. A017ETW

      Using a "TORX" driver (T25), remove the 3 screws and the rear power window regulator motor assembly.

  20. Click here

    REMOVE REAR DOOR LOCK ASSEMBLY


    1. A017FJ9

      Using a "TORX" socket wrench (T30), remove the 3 screws.

    2. Move the rear door lock assembly downward and pull the release plate out of the rear door outside handle frame.

    3. Remove the door lock wiring harness seal from the rear door lock assembly.

  21. Click here

    REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    1. A017FSJ

      Using a screwdriver, disengage the claw.

      Tip:

      Tape the screwdriver tip before use.

    2. A017EHD

      Remove the rear door lock remote control cable assembly.

  22. Click here

    REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY


    1. A017EZ1

      Using a screwdriver, disengage the 3 claws.

      Tip:

      Tape the screwdriver tip before use.

    2. A017D8W

      Remove the rear door inside locking cable assembly.

  23. Click here

    REMOVE REAR DOOR OUTSIDE HANDLE COVER


    1. A017D6X

      Using a "TORX" socket wrench (T30), loosen the screw.

      Tip:

      The screw cannot be removed because it is integrated into the rear door outside handle frame sub-assembly.

    2. A017CIQ

      Disengage the claw and remove the rear door outside handle cover.

  24. Click here

    REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY


    1. A017FED

      Pull and hold the release plate of the rear door outside handle frame sub-assembly as shown in the illustration.

      Note:

      The rear door outside handle assembly may be damaged when removing the rear door outside handle assembly, unless the release plate of the rear door outside handle frame sub-assembly is pulled and held.

    2. A017EAO

      Remove the rear door outside handle assembly as shown in the illustration.

  25. Click here

    REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD


    1. A017BEC

      Disengage the 3 claws and remove the rear door front outside handle pad.

  26. Click here

    REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD


    1. A017CKK

      Disengage the 2 claws and remove the rear door rear outside handle pad.

  27. Click here

    REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


    1. A017DWW

      Using a "TORX" socket wrench (T30), remove the screw.

    2. Disengage the 2 claws and remove the rear door outside handle frame sub-assembly.

  28. Click here

    REMOVE REAR DOOR BELT MOULDING ASSEMBLY


    1. A017BU7E01

      Put protective tape around the rear door belt moulding assembly.

    2. A017CT3

      Disengage the 6 claws and remove the rear door belt moulding assembly.

      Note:

      Be careful when removing the moulding as there are claws attached to the front end of the moulding.

  29. Click here

    REMOVE REAR DOOR NO. 2 WEATHERSTRIP


    1. A017FBM

      Disengage the claw.

    2. Disengage the 11 clips and remove the rear door No. 2 weatherstrip.

  30. Click here

    REMOVE REAR DOOR OUTSIDE MOULDING SUB-ASSEMBLY


    1. A017EO5

      Turn back the rear door No. 2 weatherstrip.

    2. Remove the nut.

    3. A017BUOE01

      Peel off the double-sided tape and disengage the 8 clips, and then remove the rear door outside moulding sub-assembly.

      Table 1. Text in Illustration
      *1 No. 4 Clip
      *2 No. 3 Clip

    4. Remove the gasket from the rear door outside moulding sub-assembly.

    5. Remove the 2 No. 3 clips from the rear door outside moulding sub-assembly.

    6. Remove the 6 No. 4 clips from the rear door outside moulding sub-assembly.

    7. A017CJLE01

      Remove the double-sided tape from the rear door outside moulding sub-assembly.

      Table 2. Text in Illustration
      *1 Double-sided Tape
  31. Click here

    REMOVE NO. 3 BLACK OUT TAPE


    1. Using a heat light, heat the No. 3 black out tape and vehicle body.

      Heating temperature
      Item Temperature
      Vehicle Body 40 to 60°C (104 to 140°F)
      Note:

      Do not heat the vehicle body excessively.

    2. Pull back an end of the No. 3 black out tape and pull it parallel to the vehicle body to pull it off.

  32. Click here

    REMOVE NO. 2 BLACK OUT TAPE


    1. Using a heat light, heat the No. 2 black out tape and vehicle body.

      Heating temperature
      Item Temperature
      Vehicle Body 40 to 60°C (104 to 140°F)
      Note:

      Do not heat the vehicle body excessively.

    2. Pull back an end of the No. 2 black out tape and pull it parallel to the vehicle body to pull it off.

  33. Click here

    REMOVE INNER UPPER BLACK OUT REAR DOOR TAPE


    1. Using a heat light, heat the inner upper black out rear door tape and vehicle body.

      Heating temperature
      Item Temperature
      Vehicle Body 40 to 60°C (104 to 140°F)
      Note:

      Do not heat the vehicle body excessively.

    2. Pull back an end of the inner upper black out rear door tape and pull it parallel to the vehicle body to pull it off.

  34. Click here

    REMOVE INNER FRONT BLACK OUT REAR DOOR TAPE


    1. Using a heat light, heat the inner front black out rear door tape and vehicle body.

      Heating temperature
      Item Temperature
      Vehicle Body 40 to 60°C (104 to 140°F)
      Note:

      Do not heat the vehicle body excessively.

    2. Pull back an end of the inner front black out rear door tape and pull it parallel to the vehicle body to pull it off.

  35. Click here

    REMOVE INNER REAR BLACK OUT REAR DOOR TAPE


    1. Using a heat light, heat the inner rear black out rear door tape and vehicle body.

      Heating temperature
      Item Temperature
      Vehicle Body 40 to 60°C (104 to 140°F)
      Note:

      Do not heat the vehicle body excessively.

    2. Pull back an end of the inner rear black out rear door tape and pull it parallel to the vehicle body to pull it off.