FRONT SEATBACK HEATER REMOVAL


  1. REMOVE FRONT SEAT HEADREST ASSEMBLY

  2. REMOVE FRONT OUTER SEAT TRACK COVER


    1. Operate the power seat switch knob and move the seat to the rearmost position.

    2. A017ET7

      Disengage the 2 claws and remove the front outer seat track cover.

  3. REMOVE FRONT INNER SEAT TRACK COVER


    1. A017F34

      Disengage the 2 claws and remove the front inner seat track cover.

  4. REMOVE REAR OUTER SEAT TRACK COVER


    1. Operate the power seat switch knob and move the seat to the foremost position.

    2. A017DLU

      Disengage the 2 claws and remove the rear outer seat track cover.

  5. REMOVE REAR INNER SEAT TRACK COVER


    1. A017DBE

      Disengage the 2 claws and remove the rear inner seat track cover.

  6. REMOVE FRONT SEAT ASSEMBLY


    1. A017B0K

      Remove the 2 bolts on the rear side of the seat.

    2. Operate the power seat switch knob and move the seat to the rearmost position.

    3. A017FKL

      Remove the 2 bolts on the front side of the seat.

    4. Operate the power seat switch knob and move the seat to the center position. Also, Operate the power seat switch knob and move the seatback to the upright position.

    5. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:


      • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent the airbag and seat belt pretensioner from deploying Click here.

      • If the side airbag was deployed, replace the front seat assembly with a new one.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    6. Disconnect each connector under the front seat assembly.

    7. Remove the front seat assembly.

      Note

      Be careful not to damage the vehicle body.

  7. REMOVE RECLINING POWER SEAT SWITCH KNOB


    1. A017EZ7E01

      Using a screwdriver wrapped with protective tape, disengage the 2 claws and remove the reclining power seat switch knob.

  8. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    1. A017BAQE01

      Using a screwdriver wrapped with protective tape, disengage the 4 claws and remove the slide and vertical power seat switch knob.

  9. REMOVE FRONT SEAT CUSHION SHIELD ASSEMBLY


    1. A017CMM

      Disengage the hooks.

    2. A017EGR

      Remove the 5 screws.

    3. Disengage the claw.

    4. Disengage the guide and remove the front seat cushion shield assembly.

    5. w/o Seat Cushion Front Edge Adjustment Function:

      Disconnect the connector from the front power seat lumbar switch.

    6. w/ Seat Cushion Front Edge Adjustment Function:


      1. Disconnect the connector from the front power seat lumbar switch and the seat variable cushion switch.

      2. Disengage each clamp.

  10. REMOVE FRONT SEAT INNER BELT ASSEMBLY


    1. Disconnect each connector and clamp.

    2. A017FR3

      Remove the nut and the front seat inner belt assembly.

  11. REMOVE FRONT SEAT CUSHION INNER SHIELD


    1. A017F7D

      Remove the screw.

    2. Disengage the claw.

    3. A017FUH

      Disengage the guide and remove the front seat cushion inner shield as shown in the illustration.

  12. REMOVE FRONT SEATBACK COVER WITH PAD


    1. A017BS7

      Remove the 3 hog rings.

    2. A017E3M

      Remove the 5 hog rings.

    3. A017G5S

      Disengage the 2 hooks.

    4. A017C9W

      Turn back the separate type front seatback cover to remove the nut, and separate the bracket of the separate type front seatback cover.

    5. A017DQF

      Disengage the 4 claws and remove the 2 front seat headrest supports.

    6. Remove the separate type front seatback cover with pad from the front seat frame assembly with adjuster.

  13. REMOVE SEPARATE TYPE FRONT SEATBACK COVER


    1. Remove the 7 hog rings and the separate type front seatback cover.

      A017C0RE01