LUMBAR SUPPORT ADJUSTER ASSEMBLY INSTALLATION


  1. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY


    1. A017BK4

      Install the lumbar support adjuster assembly with the 2 screws.

    2. Connect the connector.

  2. INSTALL FRONT SEATBACK COVER WITH PAD


    1. Temporarily install the front seatback cover with pad to the front seat frame assembly with adjuster.

    2. A017DQF

      Engage the 4 claws and install the 2 front seat headrest supports.

    3. A017C9W

      Install the front seatback cover bracket with the nut.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      Note


      • For vehicles with side airbags, the side airbags may not be activated normally unless the front seatback cover is securely installed.

      • Check that the strap is not twisted after installing the bracket.

      • Install the bracket securely.

    4. A017G5S

      Engage the hooks.

    5. A017G33E01

      Using hog ring pliers, install 5 new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

    6. A017B5JE01

      Using hog ring pliers, install the separate type front seatback cover with 3 new hog rings.

      Note


      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

  3. INSTALL FRONT SEAT CUSHION INNER SHIELD


    1. A017G67

      Engage the guide and temporarily install the front seat cushion inner shield as shown in the illustration.

    2. A017F7D

      Engage the claw.

    3. Install the front seat cushion inner shield with the screw.

  4. INSTALL FRONT SEAT INNER BELT ASSEMBLY


    1. A017FASE01

      Install the front seat inner belt assembly with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

    2. Connect each connector and clamp.

  5. INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY


    1. w/o Seat Cushion Front Edge Adjustment Function:

      Connect the connector to the front power seat lumbar switch.

    2. w/ Seat Cushion Front Edge Adjustment Function:


      1. Engage the each clamps.

      2. Connect the connector to the front power seat lumbar switch and the seat variable cushion switch.

    3. A017EGR

      Engage the guide and the claw.

    4. Install the front seat cushion shield assembly with the 5 screws.

    5. A017CMM

      Engage the hooks.

  6. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    1. A017BU4

      Engage the 4 claws and install the slide and vertical power seat switch knob.

  7. INSTALL RECLINING POWER SEAT SWITCH KNOB


    1. A017D30

      Engage the 2 claws and install the reclining power seat switch knob.

  8. INSTALL FRONT SEAT ASSEMBLY


    1. Place the front seat assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Connect the connectors under the seat.

    3. Connect the cable to the negative (-) battery terminal.

      Note

      When reconnected the cable, some systems need to be initialized Click here.

    4. Temporarily install the front seat assembly with the 4 bolts.

    5. Operate the power seat switch knob and move the seat to the rearmost position.

    6. A017FKLE01

      Tighten the 2 bolts on the front side of the seat.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

      Tech Tips

      Tighten the bolts in the order indicated in the illustration.

    7. Operate the power seat switch knob and move the seat to the foremost position.

    8. A017B0KE01

      Tighten the 2 bolts on the rear side of the seat.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

      Tech Tips

      Tighten the bolts in the order indicated in the illustration.

  9. INSTALL REAR INNER SEAT TRACK COVER


    1. A017DBE

      Engage the 2 claws and install the rear inner seat track cover.

  10. INSTALL REAR OUTER SEAT TRACK COVER


    1. A017DLU

      Engage the 2 claws and install the rear outer seat track cover.

  11. INSTALL FRONT INNER SEAT TRACK COVER


    1. Operate the power seat switch knob and move the seat to the rearmost position.

    2. A017F34

      Engage the 2 claws and install the front inner seat track cover.

  12. INSTALL FRONT OUTER SEAT TRACK COVER


    1. A017ET7

      Engage the 2 claws and install the front outer seat track cover.

  13. INSTALL FRONT SEAT HEADREST ASSEMBLY

  14. INSPECT FRONT SEAT ASSEMBLY


    1. Inspect the power seat operation.

    2. w/ Seat Heater System:

      Check the seat heater operation.


      1. Turn the ignition switch on (IG).

      2. Turn the seat heater switch on.

      3. Wait 5 minutes or more and confirm that the seat surface becomes warm.

  15. INSPECT SRS WARNING LIGHT

    Click here