LUMBAR SUPPORT ADJUSTER ASSEMBLY INSTALLATION

INSTALL FRONT SEATBACK COVER WITH PAD

1. Temporarily install the front seatback cover with pad to the front seat frame assembly with adjuster.

2. 

   Engage the 4 claws and install the 2 front seat headrest supports.

3. 

   Install the front seatback cover bracket with the nut.

   5.5 N*m

   56 kgf*cm

   49 in.*lbf

   Note:
   

   • For vehicles with side airbags, the side airbags may not be activated normally unless the front seatback cover is securely installed.

   • Check that the strap is not twisted after installing the bracket.

   • Install the bracket securely.

4. 

   Engage the hooks.

5. 

   Using hog ring pliers, install 5 new hog rings.

   Note:
   

   • Be careful not to damage the cover.

   • When installing the hog rings, take care to minimize wrinkles as much as possible.

6. 

   Using hog ring pliers, install the separate type front seatback cover with 3 new hog rings.

   Note:
   

   • Be careful not to damage the cover.

   • When installing the hog rings, take care to minimize wrinkles as much as possible.

INSTALL FRONT SEAT CUSHION INNER SHIELD

1. 

   Engage the guide and temporarily install the front seat cushion inner shield as shown in the illustration.

2. 

   Engage the claw.

3. Install the front seat cushion inner shield with the screw.

INSTALL FRONT SEAT INNER BELT ASSEMBLY

1. 

   Install the front seat inner belt assembly with the nut.

   42 N*m

   428 kgf*cm

   31 ft.*lbf

   Note:

   Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

2. Connect each connector and clamp.

INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY

1. w/o Seat Cushion Front Edge Adjustment Function:

   Connect the connector to the front power seat lumbar switch.

2. w/ Seat Cushion Front Edge Adjustment Function:

   
   

   1. Engage the each clamps.

   2. Connect the connector to the front power seat lumbar switch and the seat variable cushion switch.

3. 

   Engage the guide and the claw.

4. Install the front seat cushion shield assembly with the 5 screws.

5. 

   Engage the hooks.

INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

1. 

   Engage the 4 claws and install the slide and vertical power seat switch knob.

INSTALL RECLINING POWER SEAT SWITCH KNOB

1. 

   Engage the 2 claws and install the reclining power seat switch knob.

INSTALL FRONT SEAT ASSEMBLY

1. Place the front seat assembly in the cabin.

   Note:

   Be careful not to damage the vehicle body.

2. Connect the connectors under the seat.

3. Connect the cable to the negative (-) battery terminal.

   Note:

   When reconnected the cable, some systems need to be initialized (Click here).

4. Temporarily install the front seat assembly with the 4 bolts.

5. Operate the power seat switch knob and move the seat to the rearmost position.

6. 

   Tighten the 2 bolts on the front side of the seat.

   37 N*m

   377 kgf*cm

   27 ft.*lbf

   Tip:

   Tighten the bolts in the order indicated in the illustration.

7. Operate the power seat switch knob and move the seat to the foremost position.

8. 

   Tighten the 2 bolts on the rear side of the seat.

   37 N*m

   377 kgf*cm

   27 ft.*lbf

   Tip:

   Tighten the bolts in the order indicated in the illustration.

INSTALL REAR INNER SEAT TRACK COVER

1. 

   Engage the 2 claws and install the rear inner seat track cover.

INSTALL REAR OUTER SEAT TRACK COVER

1. 

   Engage the 2 claws and install the rear outer seat track cover.

INSTALL FRONT INNER SEAT TRACK COVER

1. Operate the power seat switch knob and move the seat to the rearmost position.

2. 

   Engage the 2 claws and install the front inner seat track cover.

INSTALL FRONT OUTER SEAT TRACK COVER

1. 

   Engage the 2 claws and install the front outer seat track cover.

INSPECT FRONT SEAT ASSEMBLY

1. Inspect the power seat operation.

2. w/ Seat Heater System:

   Check the seat heater operation.

   
   

   1. Turn the ignition switch on (IG).

   2. Turn the seat heater switch on.

   3. Wait 5 minutes or more and confirm that the seat surface becomes warm.