INSTRUMENT PANEL SAFETY PAD INSTALLATION


  1. INSTALL NO. 2 CONSOLE BOX CUP HOLDER


    1. A017EQ6

      Install the No. 2 console box cup holder.

  2. INSTALL INSTRUMENT PANEL CUP HOLDER ASSEMBLY


    1. A017DAZ

      Install the instrument panel cup holder assembly with the 4 screws <G>.

  3. INSTALL CONSOLE BOX CUP HOLDER


    1. A017CQ5

      Install the 2 console box cup holders.

  4. INSTALL NO. 3 INSTRUMENT PANEL STAY


    1. Engage the claw and install the 5 No. 3 instrument panel stays.

      A017E3U

  5. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY (for Pole Antenna Type)


    1. Engage the 5 claws.

      Note

      Do not allow the wire harness to get caught in the claws.

    2. Install the 2 bolts <D> and nut <H>.

    3. Install the 2 clips.

      A017FQ8E01

    4. Engage each clamp.

    5. Install the 2 passenger airbag bolts <A>.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

    6. Install the bolt <E>.

    7. Connect each connector and install the instrument panel safety pad assembly.

      A017D72E01

  6. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY (for Glass Antenna Type)


    1. Engage the 5 claws.

      Note

      Do not allow the wire harness to get caught in the claws.

    2. Install the 2 bolts <D> and nut <H>.

    3. Install the 2 clips.

      A017FQ8E01

    4. Engage each clamp.

    5. Install the 2 passenger airbag bolts <A>.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

    6. Connect each connector and install the instrument panel safety pad assembly.

      A017FGUE01

  7. CONNECT INSTRUMENT PANEL WIRE ASSEMBLY


    1. Check that the ignition switch is off.

    2. Check that the battery negative (-) terminal is disconnected.

      CAUTION:

      Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.

    3. A017CY2

      Connect the connector.

  8. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)


    1. A017CR7

      Connect the connector.

    2. Install the front No. 2 speaker assembly with the 2 bolts.

  9. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. A017EVH

      Engage the 2 guides.

    2. Engage the 2 claws and 2 clips, and install the No. 1 instrument panel speaker panel sub-assembly.

  10. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

    Tech Tips

    Use the same procedures for the RH side and the LH side.

  11. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. A017EGG

      Engage the 2 guides.

    2. Engage the 2 claws and 2 clips, and install the No. 2 instrument panel speaker panel sub-assembly.

  12. INSTALL FRONT PILLAR GARNISH RH


    1. A017B3UE01

      Remove the protective cover.

    2. A017D4XE01

      Install a new clip <A> on the front pillar garnish RH.

    3. Engage the 3 guides and 2 clips, then install the front pillar garnish RH.

  13. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    1. A017D8ZE01

      Align the alignment mark (pink) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

      Note

      After installation, check that the corners fit correctly.

  14. INSTALL FRONT PILLAR GARNISH LH


    1. A017BX5E01

      Remove the protective cover.

    2. A017BTZE01

      Install a new clip <A> on the front pillar garnish LH.

    3. Engage the 3 guides and 2 clips, then install the front pillar garnish LH.

  15. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. A017EEJE01

      Align the alignment mark (blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  16. INSTALL ENGINE SWITCH (w/ Smart Entry and Start System)


    1. A017G2F

      Engage the 2 claws to install the switch.

    2. Connect the switch connector.

  17. INSTALL FRONT NO. 2 CONSOLE BOX INSERT (for LHD)


    1. A017BSW

      Engage the claw and 2 guides.

    2. Install the front No. 2 console box insert with the 3 screws <F> and clip.

  18. INSTALL FRONT NO. 2 CONSOLE BOX INSERT (for RHD)


    1. A017BQH

      Engage the claw and 2 guides.

    2. Install the front No. 2 console box insert with the 3 screws <F> and clip.

  19. INSTALL FRONT NO. 1 CONSOLE BOX INSERT (for LHD)


    1. A017FLQ

      Engage the claw and 2 guides.

    2. Install the front No. 1 console box insert with the 3 screws <F> and 2 clips.

  20. INSTALL FRONT NO. 1 CONSOLE BOX INSERT (for RHD)


    1. A017BG4

      Engage the claw and 2 guides.

    2. Install the front No. 1 console box insert with the 3 screws <F> and clip.

  21. INSTALL CONSOLE BOX ASSEMBLY (w/o Rear Air Conditioning System)


    1. A017G3R

      Engage the 6 claws.

    2. A017E57

      Install the console box assembly with the 4 bolts and 2 screws.

  22. INSTALL CONSOLE BOX ASSEMBLY (w/ Rear Air Conditioning System)


    1. A017E8O

      Engage the 6 claws.

    2. Connect the connector.

    3. A017C3F

      Install the console box assembly with the 4 bolts and 2 screws.

  23. INSTALL LOWER REAR CONSOLE BOX


    1. Install the lower rear console box.

  24. INSTALL NO. 2 CONSOLE BOX DUCT (w/o Rear Air Conditioning System)


    1. A017F5N

      Install the No. 2 console box duct as shown in the illustration.

  25. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. A017FDP

      Connect the connector.

    2. Engage the 4 claws and 4 clips, and install the upper console panel sub-assembly.

  26. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    1. Connect each connector and clamp.

    2. A017F5K

      Engage the 4 claws and 3 clips.

    3. Install the lower instrument panel sub-assembly with the 2 bolts <B> and 3 screws <F>.

  27. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. A017F65

      Engage the 2 guides.

    2. Engage the 3 claws and install the No. 2 instrument panel under cover sub-assembly.

  28. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  29. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  30. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)


    1. A017BY3

      Connect the hood lock control cable assembly.

    2. Connect each connector.

    3. Engage the 3 claws and 10 clips.

    4. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.

  31. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Automatic Air Conditioning System)


    1. A017CWD

      Connect the hood lock control cable assembly.

    2. Connect each connector and the aspirator duct.

    3. A017EU2

      Engage the 3 claws and 10 clips.

    4. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.

  32. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A017G63

      Engage the claw and clip, install the cowl side trim sub-assembly LH.

    2. Install the clip.

  33. INSTALL FRONT DOOR SCUFF PLATE LH


    1. A017B6P

      Engage the guide and the 8 claws, and install the front door scuff plate LH.

  34. INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (w/o Navigation System)


    1. Connect each connector.

    2. A017EFV

      Engage the 4 clips.

    3. A017FXP

      Install the radio receiver assembly with bracket with the 4 bolts.

  35. INSTALL NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)


    1. Connect each connector.

    2. A017CTX

      Engage the 4 clips.

    3. A017EUS

      Install the navigation receiver assembly with bracket with the 4 bolts.

  36. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY WITH BRACKET (w/o Radio Receiver)


    1. Connect each connector.

    2. A017C93

      Engage the 4 clips.

    3. Install the integration control and panel assembly with bracket with the 4 bolts <D>.

  37. INSTALL HEATER CONTROL AND ACCESSORY ASSEMBLY (for Manual Air Conditioning System)


    1. Connect the connector.

    2. A017G04

      Engage the 4 clips and install the heater control and accessory assembly.

  38. INSTALL AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)


    1. Connect the connector.

    2. A017EE0

      Engage the 4 clips and install the air conditioning control assembly.

  39. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Smart Entry and Start System)


    1. A017EYQE01

      Apply protective tape to the areas shown in the illustration.

    2. Connect each connector.

    3. Engage the 10 claws and 8 clips, and install the center instrument cluster finish panel assembly.

      Note

      Do not the damage the instrument panel safety pad assembly and lower instrument panel finish panel sub-assembly.

  40. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/ Smart Entry and Start System)


    1. A017D5UE01

      Apply protective tape to the areas shown in the illustration.

    2. Connect each connector.

    3. Engage the 10 claws and 8 clips, and install the center instrument cluster finish panel assembly.

      Note

      Do not the damage the instrument panel safety pad assembly and lower instrument panel finish panel sub-assembly.

  41. INSTALL CENTER INSTRUMENT PANEL REGISTER ASSEMBLY


    1. A017DC8

      Engage the 2 claws and 5 clips, and install the center instrument panel register assembly.

  42. INSTALL COMBINATION METER ASSEMBLY


    1. Connect the connector.

    2. A017EG5

      Install the combination meter assembly with the 4 screws <F>.

  43. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    1. A017EQX

      Engage the 4 claws and 4 clips, and install the instrument cluster finish panel assembly.

  44. POSITION FRONT WHEELS STRAIGHT AHEAD

  45. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY


    1. A017EZZ

      Using pliers, engage the claw. Install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly.

    2. Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.

  46. INSTALL STEERING COLUMN COVER


    1. A017BQ8

      Engage the claw to install the upper steering column cover.

    2. A017D1F

      Engage the 2 claws to install the lower steering column cover.

    3. A017BZ5

      Install the 2 screws.

      Torque:
      2.0 N*m  { 20 kgf*cm, 18 in.*lbf }

  47. ADJUST SPIRAL CABLE SUB-ASSEMBLY


    1. Check that the ignition switch is off.

    2. Check that the battery negative (-) cable is disconnected.

      CAUTION:

      Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.

    3. A017CHQ

      Rotate the spiral cable counterclockwise slowly by hand until it stops.

      Note

      Do not turn the spiral cable using the airbag wire harness.

    4. A017E7ME01

      Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.

      Note

      Do not turn the spiral cable using the airbag wire harness.

      Tech Tips

      The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.

  48. INSTALL STEERING WHEEL ASSEMBLY


    1. A017E10E01

      Align the matchmarks on the steering wheel assembly and steering main shaft.

    2. Install the steering wheel assembly set nut.

      Torque:
      50 N*m  { 510 kgf*cm, 37 ft.*lbf }

    3. Connect the connectors to the spiral cable sub-assembly.

  49. INSPECT STEERING WHEEL CENTER POINT

  50. INSTALL STEERING PAD


    1. Check that the ignition switch is off.

    2. Check that the battery negative (-) terminal is disconnected.

      CAUTION:

      Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.

    3. A017C2G

      Support the steering pad with one hand as shown in the illustration.

    4. A017FLZ

      Connect the 2 airbag connectors to the steering pad.

      Note

      When handling the airbag connector, take care not to damage the airbag wire harness.

    5. Connect the horn connector to the steering pad.

    6. Confirm that the circumference groove of the "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.

    7. A017EQKE01

      Using a "TORX" socket wrench (T30), tighten the 2 "TORX" screws.

      Torque:
      8.8 N*m  { 90 kgf*cm, 78 in.*lbf }

  51. INSTALL LOWER NO. 2 STEERING WHEEL COVER


    1. A017BJG

      Install the lower No. 2 steering wheel cover with the claw.

  52. INSTALL LOWER NO. 3 STEERING WHEEL COVER


    1. A017F4M

      Install the lower No. 3 steering wheel cover with the claw.

  53. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  54. INSPECT STEERING PAD


    1. A017FBN

      With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:


      • Cuts, minute cracks or marked discoloration on the steering pad top surface or grooves.

    2. Make sure that the horn sounds.

      Tech Tips

      If the horn does not sound, inspect the horn system Click here.

  55. INSPECT SRS WARNING LIGHT

    Click here