Click here

BACK WINDOW LOCK INSTALLATION

Click here
Click here
  1. Click here

    PRECAUTION

    Note:

    • Be sure to use the centering jig when removing and installing the rear wiper motor assembly (for Glass Hatch Type). Failure to do so will result in a change of the location of the axis of the rear wiper motor assembly (for Glass Hatch Type), causing the wiping angle to change.

    • After installing the rear wiper motor assembly (for Glass Hatch Type), do not open the glass hatch before installing the rear wiper link pivot.

    • If the rear wiper motor assembly is removed without using the centering jig, the rear wiper motor assembly must be replaced with a new one.

  2. Click here

    INSTALL BACK WINDOW LOCK ASSEMBLY


    1. A017GAU

      Engage the clip and install the back window lock assembly.

    2. A017BJ1

      Install the 3 bolts.

      8.0 N*m 82 kgf*cm 71 in.*lbf
    3. A017F6F

      Engage the clamp.

    4. Connect the connector.

  3. Click here

    INSTALL REAR WIPER MOTOR ASSEMBLY


    1. A017CCBE01

      Temporarily install the rear wiper motor assembly with the 4 bolts and 2 nuts.

      Note:

      • Do not hold the rear wiper motor assembly by the rear wiper link pivot.

      • Be careful not to scratch the back door glass.

      • Do not remove the centering jig before installing the rear wiper link pivot.

    2. Tighten the 4 bolts and 2 nuts in the order shown in the illustration to install the rear wiper motor assembly.

      Bolt
      5.5 N*m 56 kgf*cm 49 in.*lbf
      Nut
      8.0 N*m 82 kgf*cm 71 in.*lbf

    3. Connect the connector.

  4. Click here

    INSTALL REAR WIPER LINK PIVOT


    1. A017CYL

      Install the rear wiper link pivot with the nut.

      7.0 N*m 71 kgf*cm 62 in.*lbf

    2. Open the glass hatch.

    3. A017B51

      Disengage the 2 guides.

    4. Disengage the 3 claws and remove the centering jig.

    5. Close the glass hatch.

  5. Click here

    INSTALL REAR WIPER LINK CAP


    1. A017FA7E01

      Apply MP grease to the entire surface of the rear wiper link cap.

      Tip:

      Make sure that the hole does not get clogged with grease and the grooves on the lip are filled with grease.

    2. A017ESU

      Install the rear wiper link cap.

  6. Click here

    INSTALL REAR WIPER ARM AND BLADE ASSEMBLY


    1. Stop the wiper motor at the automatic stop position.

    2. A017C5CE01

      When reinstalling:


      1. Clean the wiper arm serrations.

      2. Clean the wiper pivot serrations with a wire brush.

    3. A017BKPE01

      Place the rear wiper arm and blade assembly so that the rear wiper blade is aligned with the ceramic line.

      Area Dimension
      A 10 mm (0.39 in.)

    4. Install the rear wiper arm and blade assembly with the nut.

      5.5 N*m 56 kgf*cm 49 in.*lbf
      Tip:

      Hold down the wiper arm by hand when tightening the nut.

  7. Click here

    INSTALL REAR WIPER ARM HEAD CAP


    1. A017DOH

      Install the rear wiper arm head cap.

      Tip:

      Push down on the cap until a click sound can be heard.

  8. Click here

    INSTALL REAR WIPER SHAFT COVER


    1. Open the glass hatch.

    2. A017G4Z

      Engage the 3 clips and install the rear wiper shaft cover.

    3. Operate the rear wiper while spraying washer fluid on the glass. Make sure that the rear wiper functions properly and there is no interference with the vehicle body.

  9. Click here

    INSTALL BACK DOOR TRIM PANEL ASSEMBLY


    1. A017CKT

      Engage the 16 clips and install the back door trim panel assembly.

  10. Click here

    INSTALL ASSIST STRAP ASSEMBLY


    1. A017FJZ

      Install the assist strap assembly with the bolt.

  11. Click here

    INSTALL ASSIST STRAP HOLE COVER


    1. A017CPS

      Engage the 2 guides and 2 claws, and install the assist strap hole cover.

  12. Click here

    INSTALL BACK DOOR LOCK COVER


    1. A017G02

      Engage the 4 guides and 2 claws, and install the back door lock cover.

  13. Click here

    INSTALL BACK DOOR TRIM COVER LH (w/o Power Back Door)


    1. A017BOQ

      Engage the 2 clips and 2 claws, and install the back door trim cover LH.

  14. Click here

    INSTALL BACK DOOR TRIM COVER LH (w/ Power Back Door)


    1. A017ERC

      Engage the 2 clips and 2 claws, and install the back door trim cover LH.

  15. Click here

    CONNECT POWER BACK DOOR ROD (w/ Power Back Door)


    1. A017F50

      Install the back door stay plate and connect the power back door rod.

      18 N*m 184 kgf*cm 13 ft.*lbf
  16. Click here

    INSTALL BACK DOOR SERVICE HOLE COVER LH (w/ Power Back Door)


    1. A017ECX

      Engage the 6 claws and install the back door service hole cover LH.

  17. Click here

    INSTALL BACK DOOR TRIM COVER RH


    1. A017D6U

      Engage the 2 clips and 2 claws, and install the back door trim cover RH.

  18. Click here

    INSTALL BACK WINDOW UPPER TRIM PANEL ASSEMBLY


    1. A017EYI

      Engage the 4 clips and 4 claws, and install the back window upper trim panel assembly.