POWER WINDOW REGULATOR MOTOR REMOVAL


  1. DISCONNECT BATTERY NEGATIVE TERMINAL

  2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH (for Front Door)


    1. A017CI2

      Disengage the claw and clip, and remove the front door lower frame bracket garnish.

  3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG (for Front Door)


    1. A017F1XE01

      Using a screwdriver with the tip wrapped with protective tape, disengage the 3 claws, and remove the front door inside handle bezel plug.

  4. REMOVE FRONT ARMREST UPPER BASE PANEL (for Front Door)


    1. A017FEPE01

      Using a screwdriver with the tip wrapped with protective tape, disengage the 7 claws and clip, and remove the front armrest upper base panel.

    2. Disconnect the connector.

  5. REMOVE ASSIST GRIP COVER (for Front Door)


    1. A017EAME01

      Using a screwdriver with the tip wrapped with protective tape, disengage the 4 claws and remove the assist grip cover.

  6. REMOVE COURTESY LIGHT ASSEMBLY (for Front Door)


    1. A017DZME01

      Using a screwdriver with the tip wrapped with protective tape, disengage the claw and remove the courtesy light assembly.

    2. Disconnect the connector.

  7. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY (for Front Door)


    1. A017FDZ

      Remove the 3 screws.

    2. A017FU9

      Using a clip remover, disengage the 9 clips.

    3. Disengage the 5 claws and separate the front door trim board sub-assembly from the front door inner glass weatherstrip.

    4. A017EHB

      Disengage the 2 clamps.

    5. Disconnect the front door lock remote control cable and front door inside locking cable.

    6. Disconnect the connector.

  8. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP (for Front Door)


    1. A017ESJ

      Remove the front door inner glass weatherstrip from the front door panel.

  9. REMOVE FRONT DOOR SERVICE HOLE COVER (for Front Door)


    1. A017DHL

      Disconnect the each connector and 2 clamps, and remove the front door service hole cover.

      Tech Tips

      Remove the remaining butyl tape on the door side.

  10. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY (for Front Door)


    1. A017E3V

      Remove the hole plug.

    2. Connect the negative battery terminal.

    3. Connect the power window regulator motor connector.

    4. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

    5. Disconnect the negative battery terminal and power window regulator master switch assembly.

    6. Disconnect the power window regulator motor connector.

    7. A017FOD

      Remove the 2 bolts.

      Note

      After the bolts are removed, do not allow the door to fall.

    8. A017D4SE01

      Remove the front door glass sub-assembly as shown in the illustration.

      Note

      Do not damage the door glass.

  11. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY (for Front Door)


    1. A017F87E01

      Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator may fall and cause damage.

    2. Remove the 5 bolts.

    3. Remove the front door window regulator sub-assembly and the front power window regulator motor assembly as a unit.

    4. Remove the temporary bolt from the front door window regulator sub-assembly.

  12. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Door)


    1. A017EES

      Using a "TORX" driver (T25), remove the 3 screws and the front power window regulator motor assembly.

  13. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG (for Rear Door)


    1. A017F1XE01

      Using a screwdriver with the tip wrapped with protective tape, disengage the 3 claws and remove the rear door inside handle bezel plug.

  14. REMOVE REAR DOOR ARMREST UPPER BASE PANEL (for Rear Door)


    1. A017EWNE01

      Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws and 2 clips, and remove the rear door armrest upper base panel.

    2. Disconnect the connector.

  15. REMOVE DOOR ASSIST GRIP COVER (for Rear Door)


    1. A017D3PE01

      Using a screwdriver with the tip wrapped with protective tape, disengage the 4 claws and remove the door assist grip cover.

  16. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY (for Rear Door)


    1. A017F2K

      Remove the 3 screws.

    2. A017GAC

      Using a clip remover, disengage the 9 clips.

    3. Disengage the 5 claws and separate the rear door trim board sub-assembly from the rear door inner glass weatherstrip.

    4. A017EA4

      Disengage the 2 clamps.

    5. Disconnect the front door lock remote control cable and rear door inside locking cable.

  17. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP


    1. A017B79

      Remove the rear door inner glass weatherstrip from the rear door panel.

  18. REMOVE REAR DOOR SERVICE HOLE COVER (for Rear Door)


    1. A017D47

      Disconnect the connector.

    2. Remove the rear door service hole cover.

      Tech Tips

      Remove the remaining tape on the door.

  19. REMOVE REAR DOOR WEATHERSTRIP (for Rear Door)


    1. Remove the upper part of the front door weatherstrip to the extent that allows removal of the rear door window division bar sub-assembly.

  20. REMOVE REAR DOOR GLASS RUN (for Rear Door)


    1. A017BMF

      Remove the rear door glass run.

  21. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY (for Rear Door)


    1. A017FHT

      Remove the rear door vent seal.

    2. A017ECI

      Remove the 2 bolts, screw, and the rear door window division bar sub-assembly.

  22. REMOVE REAR DOOR QUARTER WINDOW GLASS (for Rear Door)


    1. A017E81

      Remove the rear door quarter window glass and the rear door quarter window weatherstrip as a unit as shown in the illustration.

    2. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.

  23. REMOVE REAR DOOR GLASS SUB-ASSEMBLY (for Rear Door)


    1. A017F6A

      Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

      Note

      Do not damage the door glass.

  24. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY (for Rear Door)


    1. A017B2YE01

      Disconnect the connector.

    2. Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator may fall and cause damage.

    3. Remove the 3 bolts.

    4. Remove the rear door window regulator sub-assembly and the rear power window regulator motor assembly as a unit.

    5. Remove the temporary bolt from the rear door window regulator sub-assembly.

  25. REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear Door)


    1. A017C3N

      Connect the positive (+) lead of the battery to terminal 2, and the negative (-) lead to terminal 1 of the rear power window regulator motor assembly to move the lift arm to the position shown in the illustration.

    2. A017ETW

      Using a "TORX" driver (T25), remove the 3 screws and the rear power window regulator motor assembly.