PARKING ASSIST MONITOR SYSTEM DTC CHECK / CLEAR

Tech Tips


  • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  • If the system cannot enter the diagnostic mode, inspect all AVC-LAN communication components and repair or replace malfunctioning parts Click here.

  • After turning the ignition switch on (IG), check that the map is displayed before starting the diagnostic mode. Otherwise, some items cannot be checked.


  1. START DIAGNOSTIC MODE


    1. There are 2 methods to start diagnostic mode. Start the mode by using one of them.

    2. A017FX4E01

      Method 1


      1. Start the engine.

      2. While pressing and holding the "INFO" switch, operate the light control switch: OFF → Turn ON → Turn OFF → Turn ON → Turn OFF → Turn ON → Turn OFF.

      3. The diagnostic mode starts and the "System Check Mode" screen will be displayed. The service inspection starts automatically and the result will be displayed.

    3. A017FX4E02

      Method 2


      1. Start the engine.

      2. Press the "DISP" switch.

      3. A017DIFE11

        From the display quality adjustment screen, touch the corners of the screen in the following order: upper left → lower left → upper left → lower left → upper left → lower left.

      4. The diagnostic mode starts and the "System Check Mode" screen will be displayed. The service inspection starts automatically and the result will be displayed.

  2. FINISH DIAGNOSTIC MODE


    1. There are 2 methods to end diagnostic mode. Use one of them.


      1. Turn the ignition switch off.

      2. Press and hold the "DISP" switch for 3 seconds.

  3. DIAGNOSIS MENU


    1. A017D2WE06

      The "Diagnosis MENU" screen will be displayed by pressing the menu switch on the "System Check Mode" screen.

  4. CHECK DTC


    1. A017BYKE05

      Read the system check result.


      1. If the check result is "EXCH", "CHEK" or "Old", touch the displayed check result to view the results on the "Unit Check Mode" screen and record them.

        Tech Tips


        • If all check results are "OK", go to the communication diagnostic check.

        • If a device name is not known, its physical address is displayed.

        Tech Tips

        When proceeding to view the results of another device, press the Service switch to return to the "System Check Mode" screen. Repeat this step.

    2. A017E58E02

      Read the communication diagnostic check result.


      1. Return to the "System Check Mode" screen, and press the "LAN Mon" switch to enter the "LAN Monitor" screen.

      2. A017BVJE02

        If the check result is "CHEK" or "Old", touch the displayed check result to view the results on the individual communication diagnostic screen and record them.

        Tech Tips


        • If all check results are "No Err", the system judges that no DTC exists.

        • The sub-code (relevant device) will be indicated by its physical address.

        • When proceeding to view the results of another device, press the "Service" switch to return to the original "LAN Monitor" screen. Repeat this step.

  5. DTC CLEAR / RECHECK


    1. A017DI9E02

      Clear DTCs


      1. Press the "Code CLR" switch for 3 seconds.

      2. The check results are cleared.

    2. A017BF8E02

      Recheck


      1. Press the "Recheck" switch.

      2. A017ERJE04

        Confirm that all diagnostic codes are "OK" when the check results are displayed. If a code other than "OK" is displayed, troubleshoot again.

      3. A017ERJE05

        Press the "LAN Mon" switch to change to the "LAN Monitor" screen.

      4. A017E1UE02

        Confirm that all diagnostic codes are "No Err". If a code other than "No Err" is displayed, troubleshoot again.