NAVIGATION SYSTEM (for DVD) Illumination Circuit

DESCRIPTION

Power is supplied to the navigation receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

A017DKQE12

INSPECTION PROCEDURE

Note

The vehicle is equipped with an SRS (Supplemental Restraint System). Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System Click here.

PROCEDURE


  1. CHECK ILLUMINATION


    1. Check if the illumination for the navigation receiver assembly, steering pad switch assembly, glove box or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the tail or head position.

      Result
      Result Proceed to
      Illumination comes on for all components except steering pad switch assembly. A
      Illumination comes on for all components except navigation receiver assembly. B
      No illumination comes on (navigation receiver assembly, hazard switch, glove box, etc.). C

    B

    CHECK HARNESS AND CONNECTOR (BATTERY - NAVIGATION RECEIVER ASSEMBLY) Click here

    C

    GO TO LIGHTING SYSTEM Click here

    A

  2. CHECK HARNESS AND CONNECTOR (BATTERY - SPIRAL CABLE SUB-ASSEMBLY)


    1. Disconnect the D53 spiral cable sub-assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      D53-12 (IL+2) - Body ground Light control switch in the tail or head position 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT SPIRAL CABLE SUB-ASSEMBLY


    1. A017BLSE92
      Text in Illustration
      *a

      Component without harness connected

      (Spiral Cable Sub-assembly)
      *b Steering Pad Switch Side
      *c Vehicle Side

      Disconnect the z2 steering pad switch assembly and D53 spiral cable sub-assembly connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      z2-8 (EAU) - D53-4 (EAU) Center Below 1 Ω
      2.5 rotations to the left
      2.5 rotations to the right
      z2-5 (IL+2) - D53-12 (IL+2) Center Below 1 Ω
      2.5 rotations to the left
      2.5 rotations to the right

      Note

      The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Refer to the pages shown in the brackets.

      Tech Tips



    NG

    REPLACE SPIRAL CABLE SUB-ASSEMBLY Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)


    1. Disconnect the E2 navigation receiver assembly.

    2. Disconnect the D53 spiral cable sub-assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E2-6 (SWG) - D53-4 (EAU) Always Below 1 Ω
      D53-4 (EAU) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. INSPECT STEERING PAD SWITCH ASSEMBLY


    1. Disconnect the z2 steering pad switch assembly connector.

    2. Connect a positive (+) lead from the battery to terminal IL+2 and a negative (-) lead to terminal EAU of the steering pad switch assembly connector.

      A017FFAE05

    3. Check if the illumination for the steering pad switch assembly comes on.

      OK
      Illumination for the steering pad switch assembly comes on.
      Text in Illustration
      *a

      Component without harness connected

      (Steering Pad Switch Assembly)

      		 - -

    NG

    REPLACE STEERING PAD SWITCH ASSEMBLY Click here

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  6. CHECK HARNESS AND CONNECTOR (BATTERY - NAVIGATION RECEIVER ASSEMBLY)


    1. Disconnect the E6 navigation receiver assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      E6-10 (ILL+) - Body ground Light control switch in the tail or head position 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)


    1. Disconnect the E7 navigation receiver assembly connector.

    2. Disconnect the E1 combination meter assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E7-5 (ILL-) - E1-30 (ILL-) Always Below 1 Ω
      E7-5 (ILL-) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here