Click here

NAVIGATION SYSTEM (for DVD) OPERATION CHECK

Click here
Click here
Click here

  1. CHECK SYSTEM NORMAL CONDITION


    1. If the symptom is applicable to any of the following, it is intended behavior, and not a malfunction.

      Symptom Answer
      A longer route than expected is chosen. Depending on the road conditions, the navigation receiver assembly may determine that a longer route is quicker.
      Even when distance priority is high, the shortest route is not shown. Some routes may not be advised due to safety concerns.
      When the vehicle is put into motion immediately after the engine starts, the navigation system deviates from the actual position. If the vehicle starts before the navigation system activates, the system may not react.
      When driving on certain types of roads, especially new roads, the vehicle position deviates from the actual position. When the vehicle is driving on new roads not available on the map disc, the system attempts to match it to another nearby road, causing the position mark to deviate.
    2. A017CP0

      The following symptoms are not malfunctions, but are caused by errors inherent in the GPS, gyro sensor, speed sensor or navigation receiver assembly.


      1. The current position mark may be displayed on a nearby parallel road.

      2. A017FHC

        Immediately after a fork in the road, the current vehicle position mark may be displayed on the wrong road.

      3. A017BLX

        When the vehicle turns right or left at an intersection, the current vehicle position mark may be displayed on a nearby parallel road.

      4. A017FRY

        When the vehicle is carried, such as on a ferry, and the vehicle itself is not driving, the current vehicle position mark may be displayed in the position where the vehicle was until a measurement can be performed by the GPS.

      5. A017BDI

        When the vehicle travels on a steep hill, the current vehicle position mark may deviate from the correct position.

      6. A017FVM

        When the vehicle makes a continuous turn (e.g. 360, 720, 1080 degrees), the current vehicle position mark may deviate from the correct position.

      7. A017FGC

        When the vehicle moves erratically, such as constant lane changes, the current vehicle position mark may deviate from the correct position.

      8. A017G76

        When the ignition switch is turned to ACC or ON on a turntable before parking, the current vehicle position mark may not indicate the correct direction. The same will occur when the vehicle comes out of the parking garage.

      9. A017B2E

        When the vehicle travels on a snowy road or a mountain path with tire chains installed or using a spare tire, the current vehicle position mark may deviate from the correct position.

      10. A017ESS

        When the tires are changed, the current vehicle position mark may deviate from the correct position.

        Tip:

        • A change in tire diameter may cause a speed sensor error.

        • Performing "tire change" in calibration mode will allow the system to correct the current vehicle position faster.

  2. CHECK PANEL & STEERING SWITCH

    Tip:

    • The navigation receiver assembly panel switches and steering switch are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode (Click here).

    2. A017B0X

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A017E9H

      Select "Panel&Steering Switch" from the "Function Check/Setting" screen.

    4. Panel&Steering Switch Check Mode


      1. A017B8ME01

        Operate each switch and check that the switch names and condition are correctly displayed.

        Table 1. Screen Description
        Display Content
        *1: Name of switch being pushed

        • Name of the pushed switch is displayed.

        • If more than one switch is pressed, "MULTIPLE" will be displayed.
        *2: Rotary switch name Name of the rotary switch is displayed.
        *3: Rotary switch direction Direction of the rotary switch is displayed.

  3. CHECK TOUCH SWITCH

    Tip:

    • The touch switches on the screen are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode (Click here).

    2. A017B0X

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A017ETF

      Select "Touch Switch" from the "Function Check/Setting" screen.

    4. Touch Switch Check


      1. A017G7R

        Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.

        Tip:

        • A "+" mark is displayed where the display is touched.

        • The "+" mark remains on the display even after the finger is removed.

  4. CHECK MIC & VOICE RECOGNITION

    Tip:

    • The microphone and microphone input level are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode (Click here).

    2. A017B0X

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A017CIW

      Select "Mic&Voice Recognition" from the "Function Check/Setting" screen.

    4. Microphone&Voice Recognition Check


      1. A017BQX

        When speaking into the microphone, check that the microphone input level meter changes according to the input level.

      2. Push the recording switch and perform voice recording.

      3. Check that the recording indicator remains on while recording and that the recording can be played normally.

        Tip:

        • For details of this function, refer to Diagnosis Display Detailed Description (Click here).

        • This function is controlled by the built-in navigation ECU.

        • Select the recording switch with the blower motor of the air conditioning system stopped. If an outlet of the air conditioning system is facing the microphone, noise may be recorded.

  5. CHECK COLOR BAR

    Tip:

    • The display color on the screen is checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode (Click here).

    2. A017B0X

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A017C80

      Select "Color Bar" from the "Function Check/Setting" screen.

    4. Color Bar Check Mode


      1. A017DNC

        Select a color bar from the "Color Bar Check Mode" screen.

      2. Check the display color.

        Tip:

        • The entire screen turns to the color or stripe selected.

        • Touching the display will return to the "Color Bar Check Mode" screen.

  6. CHECK GPS & VEHICLE SENSORS

    Tip:

    • GPS information, vehicle signals and sensor signals are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode (Click here).

    2. A017B0X

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A017DXG

      Select "GPS&Vehicle Sensors" from the "Function Check/Setting" screen.

    4. GPS Information


      1. A017CQL

        When GPS information is displayed, check the GPS conditions.

        Tip:

        • This screen is updated once per second when input signals to the vehicle are changed.

        • For details of this function, refer to Diagnosis Display Detailed Description (Click here).

    5. Select "Sensors Check" from the "GPS Information" screen.

    6. Vehicle Sensors


      1. A017BHQ

        Check all the signals and sensors when vehicle signal information is displayed.

        Tip:

        • This screen is updated once per second when input signals to the vehicle are changed.

        • This screen displays vehicle signals input to the built-in navigation ECU.

        • For details of this function, refer to Diagnosis Display Detailed Description (Click here).

  7. CHECK VEHICLE SIGNALS

    Tip:

    • Vehicle signals received by the navigation receiver assembly are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode (Click here).

    2. A017B0X

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A017CQ4

      Select "Vehicle Signal" from the "Function Check/Setting" screen.

    4. Vehicle Signal Check Mode


      1. A017D3I

        When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.

        Tip:

        • Only conditions having inputs are displayed.

        • This screen displays vehicle signals input to the navigation receiver assembly (built-in navigation ECU).

        • For details of this function, refer to Diagnosis Display Detailed Description (Click here).

  8. CHECK HANDS-FREE VOLUME SETTING

    Tip:

    • The hands-free volume of a "Bluetooth" compatible phone can be adjusted using the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode (Click here).

    2. A017B0X

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A017BDC

      Select "Hands-free Volume Setting" from the "Function Check/Setting" screen.

    4. Hands-free Volume Setting


      1. A017DN1E01

        Check the hands-free volume level.

        Table 2. Screen Description
        Display Content
        *1: Receive voice level adjustment Setting possible for the voice level received from "Bluetooth" compatible phones.
        Note:

        Sound quality may deteriorate when the receive voice level is changed more than necessary. For this reason, check that the receive voice quality is still acceptable after changing this setting.