RADIO ANTENNA CORD (for Pole Antenna Type) INSTALLATION

INSTALL ANTENNA ORNAMENT
1. Install the antenna ornament.
INSTALL FENDER ANTENNA ASSEMBLY
1. Install the fender antenna assembly with the nut.
  
  Torque:
  
  12 N*m { 122 kgf*cm, 9 ft.*lbf }
2. Engage the 3 clamps.
3. Put back the insulator.
INSTALL ANTENNA NUT
1. Install the antenna nut.
INSTALL PULL TOP ANTENNA POLE SUB-ASSEMBLY
1. Install the pull top antenna pole sub-assembly by turning it in the direction of the arrow shown in the illustration.
INSTALL FRONT FENDER LINER
1. Install the front fender liner RH with the 5 clips and 7 screws.
2. Install 2 new grommets.
3. Using a 4 mm hexagon wrench, install the 2 screws.
4. Install the screw and pin hold clip.
  
  Torque:
  
  3.0 N*m { 31 kgf*cm, 27 in.*lbf }
INSTALL FRONT FENDER MOULDING SUB-ASSEMBLY

Tech Tips

Use the same procedure for the RH side and the LH side Click here.
INSTALL NO. 1 ENGINE UNDER COVER
1. Install the No. 1 engine under cover with the 6 bolts and 2 clips.
INSTALL ENGINE UNDER COVER ASSEMBLY
1. Install the engine under cover assembly with the 2 bolts, 2 screws and 5 clips.
2. Install the engine under cover assembly RR with the 2 bolts.
INSTALL ANTENNA CORD SUB-ASSEMBLY
1. Engage the 9 clamps and install the antenna cord sub-assembly.
INSTALL CENTER HEATER TO REGISTER SUB DUCT
1. Install the center heater to register sub duct with the 2 screws <F>.
INSTALL DEFROSTER NOZZLE ASSEMBLY
1. Install the defroster nozzle assembly with the 3 screws <F> and clip.
INSTALL SIDE NO. 2 DEFROSTER NOZZLE DUCT
1. Install the side No. 2 defroster nozzle duct with the screw <F>.
INSTALL SIDE NO. 1 DEFROSTER NOZZLE DUCT
1. Install the side No. 1 defroster nozzle duct with the screw <F>.
INSTALL NO. 4 HEATER TO REGISTER DUCT
1. Install the No. 4 heater to register duct with the 3 screws <F>.
INSTALL NO. 1 HEATER TO REGISTER DUCT
1. Install the No. 1 heater to register duct with the 3 screws <F>.
INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY
1. Engage the 5 claws.
  
  Note
  
  Do not allow the wire harness to get caught in the claws.
2. Install the 2 bolts <D> and nut <H>.
3. Install the 2 clips.
4. Engage each clamp.
5. Install the 2 passenger airbag bolts <A>.
  
  Torque:
  
  20 N*m { 204 kgf*cm, 15 ft.*lbf }
6. Install the bolt <E>.
7. Connect each connector and install the instrument panel safety pad assembly.
CONNECT INSTRUMENT PANEL WIRE ASSEMBLY
1. Check that the ignition switch is off.
2. Check that the battery negative (-) terminal is disconnected.
  
  CAUTION:
  
  Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.
3. Connect the connector.
INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)
1. Connect the connector.
2. Install the front No. 2 speaker assembly with the 2 bolts.
INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
1. Engage the 2 guides.
2. Engage the 2 claws and 2 clips, and install the No. 1 instrument panel speaker panel sub-assembly.
INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

Tech Tips

Use the same procedure for the RH side and the LH side.
INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
1. Engage the 2 guides.
2. Engage the 2 claws and 2 clips, and install the No. 2 instrument panel speaker panel sub-assembly.
INSTALL FRONT PILLAR GARNISH LH
1. Remove the protective cover.
2. Install a new clip <A> on the front pillar garnish LH.
3. Engage the 3 guides and 2 clips, then install the front pillar garnish LH.
INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
1. Align the alignment mark (blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
  
  Note
  
  After installation, check that the corners fit correctly.
INSTALL FRONT PILLAR GARNISH RH
1. Remove the protective cover.
2. Install a new clip <A> on the front pillar garnish RH.
3. Engage the 3 guides and 2 clips, then install the front pillar garnish RH.
INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
1. Align the alignment mark (pink) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
  
  Note
  
  After installation, check that the corners fit correctly.
INSTALL FRONT NO. 2 CONSOLE BOX INSERT
1. Engage the claw and 2 guides.
2. Install the front No. 2 console box insert with the 3 screws <F> and clip.
INSTALL FRONT NO. 1 CONSOLE BOX INSERT
1. Engage the claw and 2 guides.
2. Install the front No. 1 console box insert with the 3 screws <F> and 2 clips.
INSTALL CONSOLE BOX ASSEMBLY (w/o Rear Air Conditioning System)
1. Engage the 6 claws.
2. Install the console box assembly with the 4 bolts and 2 screws.
INSTALL CONSOLE BOX ASSEMBLY (w/ Rear Air Conditioning System)
1. Engage the 6 claws.
2. Connect the connector.
3. Install the console box assembly with the 4 bolts and 2 screws.
INSTALL LOWER REAR CONSOLE BOX
1. Install the lower rear console box.
INSTALL NO. 2 CONSOLE BOX DUCT (w/o Rear Air Conditioning System)
1. Install the No. 2 console box duct as shown in the illustration.
INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY
1. Connect the connector.
2. Engage the 4 claws and 4 clips, and install the upper console panel sub-assembly.
INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
1. Connect each connector and clamp.
2. Engage the 4 claws and 3 clips.
3. Install the lower instrument panel sub-assembly with the 2 bolts <B> and 3 screws <F>.
INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
1. Engage the 2 guides.
2. Engage the 3 claws and install the No. 2 instrument panel under cover sub-assembly.
INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
1. Connect the hood lock control cable assembly.
2. Connect each connector.
3. Engage the 3 claws and 10 clips.
4. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.
INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
1. Engage the claw and clip, install the cowl side trim sub-assembly LH.
2. Install the clip.
INSTALL FRONT DOOR SCUFF PLATE LH
1. Engage the guide and the 8 claws, and install the front door scuff plate LH.
INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

Tech Tips

Use the same procedure for the RH side and the LH side.
INSTALL FRONT DOOR SCUFF PLATE RH

Tech Tips

Use the same procedure for the RH side and the LH side.
INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET
1. Connect each connector.
2. Engage the 4 clips.
3. Install the radio receiver assembly with bracket with the 4 bolts.
INSTALL HEATER CONTROL AND ACCESSORY ASSEMBLY
1. Connect the connector.
2. Engage the 4 clips and install the heater control and accessory assembly.
INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
1. Apply protective tape to the areas shown in the illustration.
2. Connect each connector.
3. Engage the 10 claws and 8 clips, and install the center instrument cluster finish panel assembly.
  
  Note
  
  Do not the damage the instrument panel safety pad assembly and lower instrument panel finish panel sub-assembly.
INSTALL CENTER INSTRUMENT PANEL REGISTER ASSEMBLY
1. Engage the 2 claws and 5 clips, and install the center instrument panel register assembly.
INSTALL COMBINATION METER ASSEMBLY
1. Connect the connector.
2. Install the combination meter assembly with the 4 screws <F>.
INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
1. Engage the 4 claws and 4 clips, and install the instrument cluster finish panel assembly.
POSITION FRONT WHEELS STRAIGHT AHEAD
INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
1. Using pliers, engage the claw. Install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly.
2. Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.
INSTALL STEERING COLUMN COVER
1. Engage the claw to install the upper steering column cover.
2. Engage the 2 claws to install the lower steering column cover.
3. Install the 2 screws.
  
  Torque:
  
  2.0 N*m { 20 kgf*cm, 18 in.*lbf }
ADJUST SPIRAL CABLE SUB-ASSEMBLY
1. Check that the ignition switch is off.
2. Check that the battery negative (-) cable is disconnected.
  
  CAUTION:
  
  Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.
3. Rotate the spiral cable counterclockwise slowly by hand until it stops.
  
  Note
  
  Do not turn the spiral cable using the airbag wire harness.
4. Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.
  
  Note
  
  Do not turn the spiral cable using the airbag wire harness.
  
  Tech Tips
  
  The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.
INSTALL STEERING WHEEL ASSEMBLY
1. Align the matchmarks on the steering wheel assembly and steering main shaft.
2. Install the steering wheel assembly set nut.
  
  Torque:
  
  50 N*m { 510 kgf*cm, 37 ft.*lbf }
3. Connect the connectors to the spiral cable sub-assembly.
INSPECT STEERING WHEEL CENTER POINT
INSTALL STEERING PAD
1. Check that the ignition switch is off.
2. Check that the battery negative (-) terminal is disconnected.
  
  CAUTION:
  
  Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.
3. Support the steering pad with one hand as shown in the illustration.
4. Connect the 2 airbag connectors to the steering pad.
  
  Note
  
  When handling the airbag connector, take care not to damage the airbag wire harness.
5. Connect the horn connector to the steering pad.
6. Confirm that the circumference groove of the "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.
7. Using a "TORX" socket wrench (T30), tighten the 2 "TORX" screws.
  
  Torque:
  
  8.8 N*m { 90 kgf*cm, 78 in.*lbf }
INSTALL LOWER NO. 3 STEERING WHEEL COVER
1. Install the lower No. 3 steering wheel cover with the claw.
INSTALL LOWER NO. 2 STEERING WHEEL COVER
1. Install the lower No. 2 steering wheel cover with the claw.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
INSPECT STEERING PAD
1. With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:
  - Cuts, minute cracks or marked discoloration on the steering pad top surface or grooves.
2. Make sure that the horn sounds.
  
  Tech Tips
  
  If the horn does not sound, inspect the horn system Click here.
INSPECT SRS WARNING LIGHT

Click here