RADIO ANTENNA CORD (for Pole Antenna Type) REMOVAL


  1. PRECAUTION

    Click here

  2. POSITION FRONT WHEELS STRAIGHT AHEAD

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait for 90 seconds after disconnecting the cable to prevent airbag deployment Click here.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE LOWER NO. 3 STEERING WHEEL COVER


    1. A017F4M

      Disengage the claw and remove the lower No. 3 steering wheel cover.

  5. REMOVE LOWER NO. 2 STEERING WHEEL COVER


    1. A017BJG

      Disengage the claw and remove the lower No. 2 steering wheel cover.

  6. REMOVE STEERING PAD


    1. A017BXEE01

      Using a "TORX" socket wrench (T30), loosen the 2 "TORX" screws until the groove along the screw circumference catches on the screw case.

    2. A017C2G

      Pull out the steering pad from the steering wheel assembly and support the steering pad with one hand as shown in the illustration.

      Note

      When removing the steering pad, do not pull the airbag wire harness.

    3. A017ETNE01

      Disconnect the horn connector from the steering pad.

    4. Using a screwdriver with the tip wrapped with protective tape, disconnect the 2 airbag connectors and remove the steering pad.

      Note

      When handling the airbag connector, take care not to damage the airbag wire harness.

  7. REMOVE STEERING WHEEL ASSEMBLY


    1. A017E10E01

      Remove the steering wheel assembly set nut.

    2. Put matchmarks on the steering wheel assembly and the steering main shaft.

    3. Disconnect the connectors from the spiral cable.

    4. A017FPJE01

      Using SST, remove the steering wheel assembly.

      SST
      09950-50013   ( 09951-05010, 09952-05010, 09953-05020, 09954-05021 )

      Note

      Apply a small amount of grease to the threads and tip of SST (09953-05020) before use.

  8. REMOVE STEERING COLUMN COVER


    1. A017BZ5

      Remove the 2 screws.

    2. A017D1F

      Disengage the 2 claws to remove the lower steering column cover.

    3. A017BQ8

      Disengage the claw to remove the upper steering column cover.

  9. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY


    1. Disconnect the connectors from the turn signal switch assembly with spiral cable sub-assembly.

    2. A017EZZ

      Using pliers, grip the claws of the clip and remove the turn signal switch assembly with spiral cable sub-assembly.

  10. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    1. A017EQX

      Disengage the 4 claws and 4 clips, and remove the instrument cluster finish panel assembly.

  11. REMOVE COMBINATION METER ASSEMBLY


    1. A017EG5

      Remove the 4 screws <F>.

    2. Disconnect the connector and remove the combination meter assembly.

  12. REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY


    1. A017DDAE01

      Apply protective tape to the areas shown in the illustration.

    2. Using a moulding remover, disengage the 2 claws and 5 clips, and then remove the center instrument panel register assembly as shown in the illustration.

  13. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    1. A017BKEE01

      Apply protective tape to the areas shown in the illustration.

    2. Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.

      Note

      Do not pull on the small storage compartment lid. Doing so may cause damage.

    3. Disconnect each connector and remove the center instrument cluster finish panel assembly.

  14. REMOVE HEATER CONTROL AND ACCESSORY ASSEMBLY


    1. A017G04

      Disengage the 4 clips and remove the heater control and accessory assembly.

    2. Disconnect the connector.

  15. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET


    1. A017FXP

      Remove the 4 bolts.

    2. A017EFV

      Pull the radio receiver assembly with bracket toward the rear of the vehicle and disengage the 4 clips.

    3. Disconnect each connector and remove the radio receiver assembly with bracket.

  16. REMOVE FRONT DOOR SCUFF PLATE LH


    1. A017B6P

      Disengage the 8 claws and guide, and remove the front door scuff plate LH.

  17. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A017G63

      Remove the clip.

    2. Disengage the clip and claw, and remove the cowl side trim sub-assembly LH.

  18. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. A017BY3

      Remove the 2 bolts <B>.

    2. Disengage the 3 claws and 10 clips.

    3. Disconnect each connector.

    4. Disconnect the hood lock control cable assembly and remove the lower instrument panel finish panel sub-assembly.

  19. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  20. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  21. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. A017B7A

      Disengage the 3 claws.

    2. Disengage the 2 guides and remove the No. 2 instrument panel under cover sub-assembly.

  22. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    1. A017F5K

      Remove the 2 bolts <B> and 3 screws <F>.

    2. Disengage the 4 claws and 3 clips.

    3. Disconnect each connector and clamp, and remove the lower instrument panel sub-assembly.

  23. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. A017FDP

      Disengage the 4 claws and 4 clips.

    2. Disconnect the connector and remove the upper console panel sub-assembly.

  24. REMOVE NO. 2 CONSOLE BOX DUCT (w/o Rear Air Conditioning System)


    1. A017DWP

      Remove the No. 2 console box duct as shown in the illustration.

  25. REMOVE LOWER REAR CONSOLE BOX


    1. Remove the lower rear console box.

  26. REMOVE CONSOLE BOX ASSEMBLY (w/o Rear Air Conditioning System)


    1. A017E57

      Remove the 4 bolts and 2 screws.

    2. A017G3R

      Disengage the 6 claws and remove the console box assembly.

  27. REMOVE CONSOLE BOX ASSEMBLY (w/ Rear Air Conditioning System)


    1. A017C3F

      Remove the 4 bolts and 2 screws.

    2. A017E8O

      Disconnect the connector.

    3. Disengage the 6 claws, and remove the console box assembly.

  28. REMOVE FRONT NO. 1 CONSOLE BOX INSERT


    1. A017FLQ

      Using a clip remover, remove the 2 clips.

    2. Remove the 3 screws <F>.

    3. Disengage the claw and 2 guides, and then remove the front No. 1 console box insert.

  29. REMOVE FRONT NO. 2 CONSOLE BOX INSERT


    1. A017BSW

      Using a clip remover, remove the clip.

    2. Remove the 3 screws <F>.

    3. Disengage the claw and 2 guides, and then remove the front No. 2 console box insert.

  30. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

  31. REMOVE FRONT PILLAR GARNISH LH


    1. A017FEQE01

      Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

    2. Cut off the clip <A>.

    3. Disengage the 3 guides and remove the front pillar garnish LH.

    4. Remove the clip <A>.

    5. A017G92E01

      Protect the curtain shield airbag assembly.


      1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  32. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

  33. REMOVE FRONT PILLAR GARNISH RH


    1. A017G4EE01

      Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

    2. Cut off the clip <A>.

    3. Disengage the 3 guides and remove the front pillar garnish RH.

    4. Remove the clip <A>.

    5. A017D95E01

      Protect the curtain shield airbag assembly.


      1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  34. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. A017EVH

      Disengage the 2 claws and 2 clips.

    2. Disengage the 2 guides and remove the No. 1 instrument panel speaker panel sub-assembly.

  35. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)


    1. A017CR7

      Remove the 2 bolts and front No. 2 speaker assembly.

    2. Disconnect the connector.

  36. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. A017EGG

      Disengage the 2 claws and 2 clips.

    2. Disengage the 2 guides and remove the No. 2 instrument panel speaker panel sub-assembly.

  37. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  38. DISCONNECT INSTRUMENT PANEL WIRE ASSEMBLY


    1. A017CY2

      Disconnect the connector.

  39. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY


    1. Disconnect each connector.

    2. Remove the bolt <E>.

    3. Remove the 2 passenger airbag bolts <A>.

    4. Disengage each clamp.

      A017D72E01
    5. Remove the 2 clips.

    6. Remove the 2 bolts <D> and nut <H>.

    7. Disengage the 5 claws and remove the instrument panel safety pad assembly.

      A017FQ8E01
  40. REMOVE NO. 1 HEATER TO REGISTER DUCT


    1. A017D2S

      Remove the 3 screws <F> and the No. 1 heater to register duct.

  41. REMOVE NO. 4 HEATER TO REGISTER DUCT


    1. A017DAC

      Remove the 3 screws <F> and the No. 4 heater to register duct.

  42. REMOVE SIDE NO. 1 DEFROSTER NOZZLE DUCT


    1. A017DON

      Remove the screw <F> and the side No. 1 defroster nozzle duct.

  43. REMOVE SIDE NO. 2 DEFROSTER NOZZLE DUCT


    1. A017B1G

      Remove the screw <F> and the side No. 2 defroster nozzle duct.

  44. REMOVE DEFROSTER NOZZLE ASSEMBLY


    1. A017F5D

      Remove the clip.

    2. Remove the 3 screws <F> and the defroster nozzle assembly.

  45. REMOVE CENTER HEATER TO REGISTER SUB DUCT


    1. A017DU7

      Remove the 2 screws <F> and the center heater to register sub duct.

  46. REMOVE ANTENNA CORD SUB-ASSEMBLY


    1. Disengage the 9 clamps and remove the antenna cord sub-assembly.

      A017CS9
  47. REMOVE ENGINE UNDER COVER ASSEMBLY


    1. A017FPR

      Remove the 2 bolts and engine under cover assembly RR.

    2. A017FXN

      Remove the 2 bolts, 2 screws, 5 clips and engine under cover assembly.

  48. REMOVE NO. 1 ENGINE UNDER COVER


    1. A017B8T

      Remove the 6 bolts, 2 clips and No. 1 engine under cover.

  49. REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  50. REMOVE FRONT FENDER LINER


    1. A017FSUE01

      Remove the screw.

    2. Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

    3. A017EB7

      Using a 4 mm hexagon wrench, remove the 2 screws.

    4. Remove the 2 grommets.

      Tech Tips

      The grommets need to be replaced with new ones because they will break when they are removed.

    5. A017B8K

      Remove the 5 clips, 7 screws and front fender liner RH.

  51. REMOVE PULL TOP ANTENNA POLE SUB-ASSEMBLY


    1. A017B9W

      Remove the pull top antenna pole sub-assembly by turning it in the direction of the arrow shown in the illustration.

  52. REMOVE ANTENNA NUT


    1. A017ELM

      Remove the antenna nut.

  53. REMOVE FENDER ANTENNA ASSEMBLY


    1. Roll up part of the insulator.

    2. A017CJH

      Disengage the 3 clamps.

    3. A017CJT

      Remove the nut and fender antenna assembly.

  54. REMOVE ANTENNA ORNAMENT


    1. A017DVM

      Remove the antenna ornament.