RADIO ANTENNA CORD (for Glass Antenna Type) REMOVAL


  1. PRECAUTION

    Click here

  2. POSITION FRONT WHEELS STRAIGHT AHEAD

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait for 90 seconds after disconnecting the cable to prevent airbag deployment Click here.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE LOWER NO. 3 STEERING WHEEL COVER


    1. A017F4M

      Disengage the claw and remove the lower No. 3 steering wheel cover.

  5. REMOVE LOWER NO. 2 STEERING WHEEL COVER


    1. A017BJG

      Disengage the claw and remove the lower No. 2 steering wheel cover.

  6. REMOVE STEERING PAD


    1. A017BXEE01

      Using a "TORX" socket wrench (T30), loosen the 2 "TORX" screws until the groove along the screw circumference catches on the screw case.

    2. A017C2G

      Pull out the steering pad from the steering wheel assembly and support the steering pad with one hand as shown in the illustration.

      Note

      When removing the steering pad, do not pull the airbag wire harness.

    3. A017ETNE01

      Disconnect the horn connector from the steering pad.

    4. Using a screwdriver with the tip wrapped with protective tape, disconnect the 2 airbag connectors and remove the steering pad.

      Note

      When handling the airbag connector, take care not to damage the airbag wire harness.

  7. REMOVE STEERING WHEEL ASSEMBLY


    1. A017E10E01

      Remove the steering wheel assembly set nut.

    2. Put matchmarks on the steering wheel assembly and the steering main shaft.

    3. Disconnect the connectors from the spiral cable.

    4. A017FPJE01

      Using SST, remove the steering wheel assembly.

      SST
      09950-50013   ( 09951-05010, 09952-05010, 09953-05020, 09954-05021 )

      Note

      Apply a small amount of grease to the threads and tip of SST (09953-05020) before use.

  8. REMOVE STEERING COLUMN COVER


    1. A017BZ5

      Remove the 2 screws.

    2. A017D1F

      Disengage the 2 claws to remove the lower steering column cover.

    3. A017BQ8

      Disengage the claw to remove the upper steering column cover.

  9. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY


    1. Disconnect the connectors from the turn signal switch assembly with spiral cable sub-assembly.

    2. A017EZZ

      Using pliers, grip the claws of the clip and remove the turn signal switch assembly with spiral cable sub-assembly.

  10. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    1. A017EQX

      Disengage the 4 claws and 4 clips, and remove the instrument cluster finish panel assembly.

  11. REMOVE COMBINATION METER ASSEMBLY


    1. A017EG5

      Remove the 4 screws <F>.

    2. Disconnect the connector and remove the combination meter assembly.

  12. REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY


    1. A017DDAE01

      Apply protective tape to the areas shown in the illustration.

    2. Using a moulding remover, disengage the 2 claws and 5 clips, and then remove the center instrument panel register assembly as shown in the illustration.

  13. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Smart Entry and Start System)


    1. A017BKEE01

      Apply protective tape to the areas shown in the illustration.

    2. Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.

      Note

      Do not pull on the small storage compartment lid. Doing so may cause damage.

    3. Disconnect each connector and remove the center instrument cluster finish panel assembly.

  14. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/ Smart Entry and Start System)


    1. A017EABE01

      Apply protective tape to the areas shown in the illustration.

    2. Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.

      Note

      Do not pull on the small storage compartment lid. Doing so may cause damage.

    3. Disconnect each connector and remove the center instrument cluster finish panel assembly.

  15. REMOVE HEATER CONTROL AND ACCESSORY ASSEMBLY (for Manual Air Conditioning System)


    1. A017G04

      Disengage the 4 clips and remove the heater control and accessory assembly.

    2. Disconnect the connector.

  16. REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)


    1. A017EE0

      Disengage the 4 clips and remove the air conditioning control assembly.

    2. Disconnect the connector.

  17. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/o Navigation System)


    1. A017FXP

      Remove the 4 bolts.

    2. A017EFV

      Pull the radio receiver assembly with bracket toward the rear of the vehicle and disengage the 4 clips.

    3. Disconnect each connector and remove the radio receiver assembly with bracket.

  18. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)


    1. A017EUS

      Remove the 4 bolts.

    2. A017CTX

      Pull the navigation receiver assembly with bracket toward the rear of the vehicle and disengage the 4 clips.

    3. Disconnect each connector and remove the navigation receiver assembly with bracket.

  19. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY WITH BRACKET (w/o Radio Receiver)


    1. A017C93

      Remove the 4 bolts <D>.

    2. Disengage the 4 clips.

    3. Disconnect each connector and remove the integration control and panel assembly with bracket.

  20. REMOVE FRONT DOOR SCUFF PLATE LH


    1. A017B6P

      Disengage the 8 claws and guide, and remove the front door scuff plate LH.

  21. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A017G63

      Remove the clip.

    2. Disengage the clip and claw, and remove the cowl side trim sub-assembly LH.

  22. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)


    1. A017BY3

      Remove the 2 bolts <B>.

    2. Disengage the 3 claws and 10 clips.

    3. Disconnect each connector.

    4. Disconnect the hood lock control cable assembly and remove the lower instrument panel finish panel sub-assembly.

  23. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Automatic Air Conditioning System)


    1. A017EU2

      Remove the 2 bolts <B>.

    2. Disengage the 3 claws and 10 clips.

    3. A017CWD

      Disconnect each connector and the aspirator duct.

    4. Disconnect the hood lock control cable assembly and remove the lower instrument panel finish panel sub-assembly.

  24. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  25. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  26. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. A017B7A

      Disengage the 3 claws.

    2. Disengage the 2 guides and remove the No. 2 instrument panel under cover sub-assembly.

  27. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    1. A017F5K

      Remove the 2 bolts <B> and 3 screws <F>.

    2. Disengage the 4 claws and 3 clips.

    3. Disconnect each connector and clamp, and remove the lower instrument panel sub-assembly.

  28. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. A017FDP

      Disengage the 4 claws and 4 clips.

    2. Disconnect the connector and remove the upper console panel sub-assembly.

  29. REMOVE NO. 2 CONSOLE BOX DUCT (w/o Rear Air Conditioning System)


    1. A017DWP

      Remove the No. 2 console box duct as shown in the illustration.

  30. REMOVE LOWER REAR CONSOLE BOX


    1. Remove the lower rear console box.

  31. REMOVE CONSOLE BOX ASSEMBLY (w/o Rear Air Conditioning System)


    1. A017E57

      Remove the 4 bolts and 2 screws.

    2. A017G3R

      Disengage the 6 claws and remove the console box assembly.

  32. REMOVE CONSOLE BOX ASSEMBLY (w/ Rear Air Conditioning System)


    1. A017C3F

      Remove the 4 bolts and 2 screws.

    2. A017E8O

      Disconnect the connector.

    3. Disengage the 6 claws, and remove the console box assembly.

  33. REMOVE FRONT NO. 1 CONSOLE BOX INSERT (for LHD)


    1. A017FLQ

      Using a clip remover, remove the 2 clips.

    2. Remove the 3 screws <F>.

    3. Disengage the claw and 2 guides, and then remove the front No. 1 console box insert.

  34. REMOVE FRONT NO. 1 CONSOLE BOX INSERT (for RHD)


    1. A017BG4

      Using a clip remover, remove the clip.

    2. Remove the 3 screws <F>.

    3. Disengage the claw and 2 guides, and then remove the front No. 1 console box insert.

  35. REMOVE FRONT NO. 2 CONSOLE BOX INSERT (for LHD)


    1. A017BSW

      Using a clip remover, remove the clip.

    2. Remove the 3 screws <F>.

    3. Disengage the claw and 2 guides, and then remove the front No. 2 console box insert.

  36. REMOVE FRONT NO. 2 CONSOLE BOX INSERT (for RHD)


    1. A017BQH

      Using a clip remover, remove the clip.

    2. Remove the 3 screws <F>.

    3. Disengage the claw and 2 guides, and then remove the front No. 2 console box insert.

  37. REMOVE ENGINE SWITCH (w/ Smart Entry and Start System)


    1. A017G2F

      Disconnect the switch connector.

    2. Disengage the 2 claws and remove the switch.

  38. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. A017G5W

      Remove the front door opening trim weatherstrip LH.

  39. REMOVE FRONT PILLAR GARNISH LH


    1. A017FEQE01

      Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

    2. Cut off the clip <A>.

    3. Disengage the 3 guides and remove the front pillar garnish LH.

    4. Remove the clip <A>.

    5. A017G92E01

      Protect the curtain shield airbag assembly.


      1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  40. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  41. REMOVE FRONT PILLAR GARNISH RH


    1. A017G4EE01

      Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

    2. Cut off the clip <A>.

    3. Disengage the 3 guides and remove the front pillar garnish RH.

    4. Remove the clip <A>.

    5. A017D95E01

      Protect the curtain shield airbag assembly.


      1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  42. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. A017EVH

      Disengage the 2 claws and 2 clips.

    2. Disengage the 2 guides and remove the No. 1 instrument panel speaker panel sub-assembly.

  43. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)


    1. A017CR7

      Remove the 2 bolts and front No. 2 speaker assembly.

    2. Disconnect the connector.

  44. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. A017EGG

      Disengage the 2 claws and 2 clips.

    2. Disengage the 2 guides and remove the No. 2 instrument panel speaker panel sub-assembly.

  45. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  46. DISCONNECT INSTRUMENT PANEL WIRE ASSEMBLY


    1. A017CY2

      Disconnect the connector.

  47. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY


    1. Disconnect each connector.

    2. Remove the 2 passenger airbag bolts <A>.

    3. Disengage each clamp.

      A017FGUE01

    4. Remove the 2 clips.

    5. Remove the 2 bolts <D> and nut <H>.

    6. Disengage the 5 claws and remove the instrument panel safety pad assembly.

      A017FQ8E01

  48. REMOVE NO. 1 HEATER TO REGISTER DUCT


    1. A017D2S

      Remove the 3 screws <F> and the No. 1 heater to register duct.

  49. REMOVE NO. 4 HEATER TO REGISTER DUCT


    1. A017DAC

      Remove the 3 screws <F> and the No. 4 heater to register duct.

  50. REMOVE SIDE NO. 1 DEFROSTER NOZZLE DUCT


    1. A017DON

      Remove the screw <F> and the side No. 1 defroster nozzle duct.

  51. REMOVE SIDE NO. 2 DEFROSTER NOZZLE DUCT


    1. A017B1G

      Remove the screw <F> and the side No. 2 defroster nozzle duct.

  52. REMOVE DEFROSTER NOZZLE ASSEMBLY


    1. A017F5D

      Remove the clip.

    2. Remove the 3 screws <F> and the defroster nozzle assembly.

  53. REMOVE CENTER HEATER TO REGISTER SUB DUCT


    1. A017DU7

      Remove the 2 screws <F> and the center heater to register sub duct.

  54. REMOVE NAVIGATION ANTENNA ASSEMBLY (w/ Navigation System)


    1. A017DU2

      Remove the 2 screws and separate the navigation antenna assembly.

    2. A017BOT

      Disengage the 3 clamps and remove the navigation antenna assembly.

  55. REMOVE ANTENNA CORD SUB-ASSEMBLY


    1. Disengage the 9 clamps and remove the antenna cord sub-assembly.

      A017G31E01

  56. REMOVE REAR CENTER SEAT ASSEMBLY

  57. REMOVE REAR SEAT HEADREST ASSEMBLY (for LH Side)

  58. REMOVE REAR SEAT TRACK BRACKET COVER LH


    1. A017DZY

      Disengage the 8 claws and remove the 2 rear seat track bracket covers.

  59. REMOVE REAR OUTER TRACK BRACKET COVER LH


    1. A017BNT

      Disengage the 4 claws and remove the rear outer track bracket cover.

  60. REMOVE REAR INNER TRACK BRACKET COVER LH


    1. A017FUU

      Disengage the 4 claws and remove the rear inner track bracket cover.

  61. REMOVE REAR SEAT LEG SIDE COVER LH


    1. A017BXU

      Disengage the 3 claws.

    2. Disengage the clip and remove the rear seat leg side cover.

  62. DISCONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY LH (w/ Remote Folding Function)


    1. Pull down the adjuster's lock piece to release the lock as shown in the illustration.

      A017BM1E01
    2. A017BWQE01

      Using a screwdriver wrapped with protective tape, disengage the 2 claws as shown in the illustration.

    3. Lift up the seat track adjusting handle to the uppermost position and hold the handle in this position as shown in the illustration.

      A017BFVE01

    4. Using a screwdriver wrapped with protective tape, disconnect the rear No. 1 seat lock cable assembly as shown in the illustration.

    5. Using a screwdriver wrapped with protective tape, disconnect the rear seat reclining control cable as shown in the illustration.

      A017FFKE01

    6. Secure the rear seat reclining control cable with the carpet hole as shown in the illustration.

  63. REMOVE REAR NO. 1 SEAT ASSEMBLY LH


    1. A017BHD

      Remove the 3 bolts on the rear side of the seat.

    2. A017FCR

      Remove the 2 bolts on the front side of the seat and the rear No. 1 seat assembly.

      Note

      Be careful not to damage the vehicle body.

  64. REMOVE REAR SEAT HEADREST ASSEMBLY (for RH Side)

  65. REMOVE REAR SEAT TRACK BRACKET COVER RH


    1. A017ERX

      Disengage the 8 claws and remove the 2 rear seat track bracket covers.

  66. REMOVE REAR OUTER TRACK BRACKET COVER RH


    1. A017D2L

      Disengage the 4 claws and remove the rear outer track bracket cover.

  67. REMOVE REAR INNER TRACK BRACKET COVER RH


    1. A017F59

      Disengage the 4 claws and remove the rear inner track bracket cover.

  68. REMOVE REAR SEAT LEG SIDE COVER RH


    1. A017F28

      Disengage the 3 claws.

    2. Disengage the clip and remove the rear seat leg side cover.

  69. DISCONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY RH (w/ Remote Folding Function)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  70. REMOVE REAR NO. 1 SEAT ASSEMBLY RH


    1. A017EZ3

      Remove the 3 bolts on the rear side of the seat.

    2. A017D5O

      Remove the 2 bolts on the front side of the seat and the rear No. 1 seat assembly.

      Note

      Be careful not to damage the vehicle body.

  71. REMOVE REAR DOOR SCUFF PLATE LH


    1. A017D4T

      Disengage the 5 claws, 3 clips and guide, and remove the rear door scuff plate LH.

  72. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. A017C1V

      Remove the rear door opening trim weatherstrip LH.

  73. REMOVE LOWER CENTER PILLAR GARNISH LH


    1. A017F82

      Disengage the 2 claws and 2 clips, and remove the lower center pillar garnish LH.

  74. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    1. A017G6U

      Remove the bolt and disconnect the floor end of the front seat outer belt assembly.

  75. REMOVE CENTER PILLAR GARNISH LH


    1. A017B73

      Remove the screw and clip.

    2. Disengage the 2 guides and clip, and remove the center pillar garnish LH.

  76. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  77. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  78. REMOVE LOWER CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  79. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  80. REMOVE CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  81. REMOVE DECK BOARD ASSEMBLY


    1. A017CPI

      Remove the deck board assembly.

  82. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY


    1. A017F31

      Disengage the 2 guides and remove the No. 3 deck board sub-assembly.

  83. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY


    1. A017D36

      Disengage the 2 guides and remove the No. 2 deck board sub-assembly.

  84. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Remove the tonneau cover assembly.

  85. REMOVE REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)


    1. A017CVI

      Disengage the 3 clips and the 3 guides, and remove the rear No. 1 floor board.

  86. REMOVE REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)


    1. A017BBU

      Disengage the 2 clips and remove the rear seat side cover LH.

  87. REMOVE DECK SIDE TRIM BOX LH


    1. A017BZVE01

      Remove the 2 deck side trim clips and clip.

    2. Remove the deck side trim box LH as shown in the illustration.

      A017G2A

  88. REMOVE REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)


    1. A017EH1

      Disengage the 2 clips and remove the rear seat side cover RH.

  89. REMOVE JACK CARRIER SUPPORT

  90. REMOVE JACK CARRIER CUSHION (for LHD)


    1. A017ENI

      Remove the jack carrier cushion.

  91. REMOVE JACK CARRIER CUSHION (for RHD)


    1. A017D41

      Remove the jack carrier cushion.

  92. REMOVE JACK ASSEMBLY (for LHD)


    1. A017EKS

      Remove the jack assembly.

  93. REMOVE JACK ASSEMBLY (for RHD)


    1. A017DSX

      Remove the jack assembly.

  94. REMOVE JACK CARRIER ASSEMBLY (for LHD)


    1. A017EAS

      Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.

  95. REMOVE JACK CARRIER ASSEMBLY (for RHD)


    1. A017D6R

      Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.

  96. REMOVE DECK SIDE TRIM BOX RH


    1. A017FOPE01

      Remove the 2 deck side trim clips and clip.

    2. Remove the deck side trim box RH as shown in the illustration.

      A017E9B

  97. REMOVE DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)


    1. A017G15

      Remove the 4 bolts and 4 nuts.

    2. Remove the deck floor board assembly.

  98. REMOVE REAR MAT


    1. A017F51

      Remove the rear mat.

  99. REMOVE DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)


    1. A017FMA

      Disengage the 3 claws.

    2. Remove the 2 nuts and the deck floor board assembly.

  100. REMOVE REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)


    1. A017D8N

      Remove the 2 nuts and the deck floor box.

  101. REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat)


    1. A017GAE

      Remove the bolt and rear No. 2 seat inner belt assembly.

      Tech Tips

      Use the same procedure for the RH side and LH side.

  102. DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat)


    1. A017F2F

      Remove the bolt and disconnect the rear seat lap type belt assembly LH.

  103. DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  104. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)


    1. A017E5S

      Remove the 4 bolts and the rear No. 2 seat assembly.

  105. REMOVE REAR FLOOR FINISH PLATE


    1. A017BSY

      Disengage the 4 clips and the 4 claws, and remove the rear floor finish plate.

  106. REMOVE DECK SIDE TRIM COVER NO.2


    1. A017FRQE01

      Using a screwdriver, disengage the 2 claws and remove the deck side trim cover LH.

      Tech Tips

      Tape the screwdriver tip before use.

  107. REMOVE DECK SIDE TRIM LH


    1. A017F36

      Remove the bolt.

    2. A017B91

      Disengage the 4 claws and the 3 guides, and remove the deck side trim LH as shown in the illustration.

  108. REMOVE SIDE TRIM COVER LH


    1. A017EO1

      Disengage the 10 claws and remove the side trim cover LH.

  109. REMOVE REAR COMBINATION LIGHT SERVICE COVER LH


    1. A017EUZE01

      Using a screwdriver, disengage the 6 claws and 2 guides, and remove the rear combination light service cover LH.

      Tech Tips

      Tape the screwdriver tip before use.

  110. REMOVE REAR POWER POINT SOCKET ASSEMBLY


    1. Disconnect the connector.

    2. A017G8M

      Disengage the claw and remove the rear power point socket assembly.

  111. REMOVE REAR POWER OUTLET SOCKET COVER


    1. A017B0H

      Disengage the 2 claws and remove the rear power outlet socket cover.

  112. REMOVE REAR DECK TRIM COVER (w/o Remote Folding Function)


    1. A017EYF

      Disengage the 10 claws and remove the rear deck trim cover.

  113. REMOVE RECLINING REMOTE CONTROL LEVER BEZEL LH (w/ Remote Folding Function)


    1. A017FIS

      Disengage the 5 claws and remove the reclining remote control bezel LH.

  114. REMOVE ROPE HOOK ASSEMBLY (for LH Side)


    1. A017FLCE01

      for Front Side:


      1. Using a screwdriver, disengage the 2 claws.

        Tech Tips

        Tape the screwdriver tip before use.

      2. Remove the bolt and the rope hook assembly.

    2. A017B9EE01

      for Rear Side:


      1. Using a screwdriver, disengage the 2 claws.

        Tech Tips

        Tape the screwdriver tip before use.

      2. Remove the bolt and rope hook assembly.

  115. REMOVE NO. 2 DECK SIDE TRIM HOOK


    1. A017CPF

      Remove the screw and the No. 2 deck side trim hook.

  116. REMOVE FRONT DECK SIDE TRIM COVER LH


    1. A017C3ZE01

      Using a screwdriver, disengage the 4 claws and remove the 2 front deck side trim covers LH.

      Tech Tips

      Tape the screwdriver tip before use.

  117. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH


    1. A017ETD

      Remove the bolt and disconnect the floor end of the rear No. 1 seat outer belt assembly.

  118. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Remove the 2 bolts.

    2. Remove the 2 clips.

    3. Disengage the 7 claws and 4 clips, and remove the deck trim side panel assembly LH.

      A017FE0

  119. REMOVE QUARTER PILLAR GARNISH LH


    1. A017DVD

      Disengage the 2 claws and 2 guides, and remove the No. 1 seat outer belt guide.

    2. A017B6M

      Disengage the 2 clips and the 2 guides, and remove the quarter pillar garnish LH.

  120. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH (w/o Power Back Door)


    1. w/o Rear No. 2 Seat:


      1. A017ES0

        Remove the bolt.

      2. Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.

    2. w/ Rear No. 2 Seat:


      1. A017DAD

        Disengage the 2 claws and 2 guides, and remove the rear No. 2 seat outer belt guide.

      2. A017FTJ

        Remove the bolt.

      3. Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.

  121. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH (w/ Power Back Door)


    1. w/o Rear No. 2 Seat:


      1. A017E6D

        Remove the bolt.

      2. Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.

    2. w/ Rear No. 2 Seat:


      1. A017DAD

        Disengage the 2 claws and 2 guides, and remove the rear No. 2 seat outer belt guide.

      2. A017EMC

        Remove the bolt.

      3. Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.

  122. REMOVE REAR SEAT SIDE GARNISH CAP (w/o Rear Air Conditioning System)


    1. A017DMI

      Disengage the 8 claws and guide, and remove the rear seat side garnish cap.

  123. REMOVE REAR SEAT SIDE GARNISH CAP (w/ Rear Air Conditioning System)


    1. A017FP0

      Remove the screw.

    2. Disengage the 6 claws and the guide, and remove the rear seat side garnish cap.

  124. REMOVE DECK SIDE TRIM COVER NO.1

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  125. REMOVE DECK SIDE TRIM RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  126. REMOVE SIDE TRIM COVER RH (w/o Rear Automatic Air Conditioning System)


    1. A017CSI

      Disengage the 4 claws and remove the side trim cover RH.

  127. REMOVE REAR ROOM TEMPERATURE SENSOR (w/ Rear Automatic Air Conditioning System)


    1. A017B3P

      Disengage the 4 claws and remove the rear room temperature sensor.

    2. Disconnect the connector.

  128. REMOVE REAR COMBINATION LIGHT SERVICE COVER RH


    1. A017BZ2E01

      Using a screwdriver, disengage the 6 claws and the 2 guides, and remove the rear combination light service cover RH.

      Tech Tips

      Tape the screwdriver tip before use.

  129. REMOVE ROPE HOOK ASSEMBLY (for RH Side)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  130. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

    Tech Tips

    Use the same procedure for the No. 1 luggage compartment trim hook and the No. 2 deck side trim hook.

  131. REMOVE FRONT DECK SIDE TRIM COVER RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  132. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  133. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH


    1. Remove the 3 bolts.

    2. Remove the 2 clips.

    3. Disengage the 7 claws and 4 clips, and remove the deck trim side panel assembly RH.

      A017FTC

  134. REMOVE QUARTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  135. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH (w/o Rear No. 2 Seat)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  136. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH (w/ Rear No. 2 Seat)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  137. REMOVE ROOF CONSOLE BOX ASSEMBLY


    1. A017G1E

      Using a moulding remover, disengage the 2 clips, 3 guides and fastener.

    2. Disconnect the connector and remove the roof console box assembly.

  138. REMOVE VISOR BRACKET COVER (for LH Side)


    1. A017FET

      Using a moulding remover, disengage the 4 claws and remove the visor bracket cover.

  139. REMOVE VISOR ASSEMBLY LH


    1. A017BSF

      Remove the 2 screws and remove the visor assembly LH.

  140. REMOVE VISOR BRACKET COVER (for RH Side)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  141. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  142. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


    1. A017DH8E01

      Disengage the 2 claws and slide the inner rear view mirror stay holder cover as shown in the illustration.

    2. A017E8X

      Disengage the 2 claws and remove the inner rear view mirror stay holder cover.

  143. REMOVE NO. 1 ROOM LIGHT ASSEMBLY (for Standard)


    1. A017BUTE02

      Using a screwdriver, disengage the 4 claws and remove the lens cover.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A017DOVE01

      Using a screwdriver, disengage the 2 claws <A> as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

    3. Disengage the 2 claws <B>.

    4. A017D1Z

      Using a screwdriver, disengage the 4 claws and remove the No. 1 room light assembly.

  144. REMOVE NO. 1 ROOM LIGHT ASSEMBLY (for Independent Type)


    1. A017EM6E01

      Using a screwdriver, disengage the 4 claws and remove the lens cover.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A017EBAE01

      Using a screwdriver, disengage the 2 claws <A> as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

    3. Disengage the 2 claws <B>.

    4. A017C7P

      Using a screwdriver, disengage the 8 claws and remove the No. 1 room light assembly.

  145. REMOVE NO. 2 ROOM LIGHT ASSEMBLY


    1. A017BUTE02

      Using a screwdriver, disengage the 4 claws and remove the lens cover.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A017DOVE01

      Using a screwdriver, disengage the 2 claws <A> as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

    3. Disengage the 2 claws <B>.

    4. A017D1Z

      Using a screwdriver, disengage the 4 claws and remove the No. 2 room light assembly.

  146. REMOVE TELEVISION BASE (w/ Rear Seat Entertainment System)


    1. A017BXW

      Disengage the 4 clips and remove the television base.

  147. REMOVE TELEVISION DISPLAY ASSEMBLY (w/ Rear Seat Entertainment System)


    1. Disconnect the connector.

    2. A017E98

      Remove the 4 bolts.

    3. A017ETX

      Disengage the 2 clips and 2 claws, and then remove the television display.

  148. REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY (w/o Sliding Roof)


    1. A017EIPE01

      Using a clip remover, disengage the 4 claws.

      Note

      Do not forcibly pry the assist grip covers to prevent them from being deformed.

      Tech Tips


      • Gently pry on the assist grip covers as shown in the illustration to remove them.

      • Tape the clip remover tip before use.

    2. A017DIC

      Pull off the 2 assist grip covers by hand.

    3. Disengage the 2 clips and remove the front assist grip sub-assembly.

    4. Remove the 2 clips from the vehicle body.

      Tech Tips

      Use the same procedure for the RH side and the LH side.

  149. REMOVE REAR ASSIST GRIP SUB-ASSEMBLY (w/o Sliding Roof)


    1. A017DR3E01

      Using a clip remover, disengage the 4 claws.

      Note

      Do not forcibly pry the assist grip covers to prevent them from being deformed.

      Tech Tips


      • Gently pry on the assist grip covers as shown in the illustration to remove them.

      • Tape the clip remover tip before use.

    2. Pull off the 2 assist grip covers by hand.

    3. A017CJX

      Disengage the 2 clips and remove the rear assist grip sub-assembly.

    4. Remove the 2 clips from the vehicle body.

      Tech Tips

      Use the same procedure for the RH side and the LH side.

  150. REMOVE ASSIST GRIP ASSEMBLY (w/ Sliding Roof)


    1. A017BF4E01

      Using a screwdriver, disengage the 6 claws and remove the 2 assist grip covers.

      Note

      Do not forcibly pry the assist grip covers to prevent them from being deformed.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A017DWA

      Disengage the 4 clips and remove the assist grip assembly.

    3. Remove the 4 clips from the vehicle body.

      Tech Tips

      Use the same procedure for the other 4 assist grips.

  151. REMOVE ROOF HEADLINING TRIM CLIP STOPPER


    1. A017EX6E01

      Using a screwdriver, disengage the 3 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Remove the bolt and the roof headlining trim clip stopper.

      Tech Tips

      Use the same procedure for the RH side and the LH side.

  152. REMOVE SUN ROOF OPENING TRIM MOULDING (w/ Sliding Roof)

  153. REMOVE VISOR HOLDER


    1. A017FUKE01

      Turn the visor holder approximately 45° and pull it out as shown in the illustration.

    2. Disengage the 2 claws and remove the visor holder.

      Tech Tips

      Use the same procedure for the RH side and the LH side.

  154. REMOVE ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)


    1. Disconnect the No. 1 roof wire connector and disengage the 3 clamps from the front pillar LH.

    2. Disconnect the No. 2 antenna cord sub-assembly connector, disengage the 3 clamps, and remove the bolt from the front pillar RH.

    3. Disconnect the No. 2 antenna cord sub-assembly connector from the rear pillar RH.

    4. Remove the 4 clips.

      A017ER8E01
    5. A017EOO

      Remove the roof headlining assembly from the vehicle through the back door.

      Note

      Do not damage the roof headlining assembly or body interior.

  155. REMOVE ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)


    1. Disconnect the No. 1 roof wire connectors and disengage the 3 clamps from the front pillar LH.

    2. w/ Rear Seat Entertainment System:


      1. Disconnect the No. 1 roof wire connector from the rear pillar LH.

    3. Disconnect the No. 2 antenna cord sub-assembly connector, disengage the 3 clamps and remove the bolt from the front pillar RH.

    4. Disconnect the No. 2 antenna cord sub-assembly connector from the rear pillar RH.

    5. Disconnect the sliding roof drive gear connector.

    6. Remove the 3 clips.

      A017FCLE01
    7. A017BD9

      Remove the roof headlining assembly from the vehicle through the back door.

      Note

      Do not damage the roof headlining assembly or body interior.

  156. REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY


    1. Peel the strips of the tape used to secure the antenna cord only to the extent that allows removal of the antenna cord.

      A017CEVE01

      Tech Tips

      Tape is not available as a supply part. Try to leave as much tape as possible on the roof headlining so that the tape can be reused.

    2. Remove the No. 2 antenna cord sub-assembly from the roof headlining.