Click here

DOOR CONTROL RECEIVER REMOVAL

Click here
Click here
  1. Click here

    DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait for 90 seconds after disconnecting the terminal to prevent airbag deployment (Click here).

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  2. Click here

    REMOVE REAR CENTER SEAT ASSEMBLY

  3. Click here

    REMOVE REAR SEAT HEADREST ASSEMBLY (for LH Side)

  4. Click here

    REMOVE SEAT TRACK BRACKET COVER LH


    1. A017DZY

      Disengage the 8 claws and remove the 2 rear seat track bracket covers.

  5. Click here

    REMOVE REAR OUTER TRACK BRACKET COVER LH


    1. A017BNT

      Disengage the 4 claws and remove the rear outer track bracket cover.

  6. Click here

    REMOVE REAR INNER TRACK BRACKET COVER LH


    1. A017FUU

      Disengage the 4 claws and remove the rear inner track bracket cover.

  7. Click here

    REMOVE REAR SEAT LEG SIDE COVER LH


    1. A017BXU

      Disengage the 3 claws.

    2. Disengage the clip and remove the rear seat leg side cover.

  8. Click here

    DISCONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY LH (w/ Remote Folding Function)


    1. A017BM1E01

      Pull down the adjuster's lock piece to release the lock as shown in the illustration.

    2. A017BWQE01

      Using a screwdriver wrapped with protective tape, disengage the 2 claws as shown in the illustration.

    3. A017BFVE01

      Lift up the seat track adjusting handle to the uppermost position and hold the handle in this position as shown in the illustration.

    4. Using a screwdriver wrapped with protective tape, disconnect the rear No. 1 seat lock cable assembly as shown in the illustration.

    5. A017FFKE01

      Using a screwdriver wrapped with protective tape, disconnect the rear seat reclining control cable as shown in the illustration.

    6. Secure the rear seat reclining control cable with the carpet hole as shown in the illustration.

  9. Click here

    REMOVE REAR NO. 1 SEAT ASSEMBLY LH


    1. A017BHD

      Remove the 3 bolts on the rear side of the seat.

    2. A017FCR

      Remove the 2 bolts on the front side of the seat and the rear No. 1 seat assembly.

      Note:

      Be careful not to damage the vehicle body.

  10. Click here

    REMOVE REAR DOOR SCUFF PLATE LH


    1. A017B6P

      Disengage the 8 claws and guide, and remove the front door scuff plate LH.

  11. Click here

    REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. A017G5W

      Remove the front door opening trim weatherstrip LH.

  12. Click here

    REMOVE DECK BOARD ASSEMBLY


    1. A017CPI

      Remove the deck board assembly.

  13. Click here

    REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY


    1. A017F31

      Disengage the 2 guides and remove the No. 3 deck board sub-assembly.

  14. Click here

    REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY


    1. A017D36

      Disengage the 2 guides and remove the No. 2 deck board sub-assembly.

  15. Click here

    REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

  16. Click here

    REMOVE REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)


    1. A017CVI

      Disengage the 3 clips and the 3 guides, and remove the rear No. 1 floor board.

  17. Click here

    REMOVE REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)


    1. A017BBU

      Disengage the 2 clips and remove the rear seat side cover LH.

  18. Click here

    REMOVE DECK SIDE TRIM BOX LH


    1. A017BZVE01

      Remove the 2 deck side trim clips and clip.

    2. A017G2A

      Remove the deck side trim box LH as shown in the illustration.

  19. Click here

    REMOVE REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)


    1. A017EH1

      Disengage the 2 clips and remove the rear seat side cover RH.

  20. Click here

    REMOVE JACK CARRIER SUPPORT

  21. Click here

    REMOVE JACK CARRIER CUSHION (for LHD)


    1. A017ENI

      Remove the jack carrier cushion.

  22. Click here

    REMOVE JACK CARRIER CUSHION (for RHD)


    1. A017D41

      Remove the jack carrier cushion.

  23. Click here

    REMOVE JACK ASSEMBLY (for LHD)


    1. A017EKS

      Remove the jack assembly.

  24. Click here

    REMOVE JACK ASSEMBLY (for RHD)


    1. A017DSX

      Remove the jack assembly.

  25. Click here

    REMOVE JACK CARRIER ASSEMBLY (for LHD)


    1. A017EAS

      Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.

  26. Click here

    REMOVE JACK CARRIER ASSEMBLY (for RHD)


    1. A017D6R

      Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.

  27. Click here

    REMOVE DECK SIDE TRIM BOX RH


    1. A017FOPE01

      Remove the 2 deck side trim clips and clip.

    2. A017E9B

      Remove the deck side trim box RH as shown in the illustration.

  28. Click here

    REMOVE DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)


    1. A017G15

      Remove the 4 bolts and 4 nuts.

    2. Remove the deck floor board assembly.

  29. Click here

    REMOVE REAR MAT


    1. A017F51

      Remove the rear mat.

  30. Click here

    REMOVE DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)


    1. A017FMA

      Disengage the 3 claws.

    2. Remove the 2 nuts and the deck floor board assembly.

  31. Click here

    REMOVE REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)


    1. A017D8N

      Remove the 2 nuts and the deck floor box.

  32. Click here

    REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat)


    1. A017GAE

      Remove the bolt and rear No. 2 seat inner belt assembly.

      Tip:

      Use the same procedure for the RH side and LH side.

  33. Click here

    DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat)


    1. A017F2F

      Remove the bolt and disconnect the rear seat lap type belt assembly LH.

  34. Click here

    DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat)

    Tip:

    Use the same procedure for the RH side and the LH side.

  35. Click here

    REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)


    1. A017E5S

      Remove the 4 bolts and the rear No. 2 seat assembly.

  36. Click here

    REMOVE REAR FLOOR FINISH PLATE


    1. A017BSY

      Disengage the 4 clips and the 4 claws, and remove the rear floor finish plate.

  37. Click here

    REMOVE DECK SIDE TRIM COVER NO.2


    1. A017FRQE01

      Using a screwdriver, disengage the 2 claws and remove the deck side trim cover LH.

      Tip:

      Tape the screwdriver tip before use.

  38. Click here

    REMOVE DECK SIDE TRIM LH


    1. A017F36

      Remove the bolt.

    2. A017B91

      Disengage the 4 claws and the 3 guides, and remove the deck side trim LH as shown in the illustration.

  39. Click here

    REMOVE SIDE TRIM COVER LH


    1. A017EO1

      Disengage the 10 claws and remove the side trim cover LH.

  40. Click here

    REMOVE REAR COMBINATION LIGHT SERVICE COVER LH


    1. A017EUZE01

      Using a screwdriver, disengage the 6 claws and 2 guides, and remove the rear combination light service cover LH.

      Tip:

      Tape the screwdriver tip before use.

  41. Click here

    REMOVE REAR POWER POINT SOCKET ASSEMBLY


    1. Disconnect the connector.

    2. A017G8M

      Disengage the claw and remove the rear power point socket assembly.

  42. Click here

    REMOVE REAR POWER OUTLET SOCKET COVER


    1. A017B0H

      Disengage the 2 claws and remove the rear power outlet socket cover.

  43. Click here

    REMOVE REAR DECK TRIM COVER (w/o Remote Folding Function)


    1. A017EYF

      Disengage the 10 claws and remove the rear deck trim cover.

  44. Click here

    REMOVE RECLINING REMOTE CONTROL BEZEL LH (w/ Remote Folding Function)


    1. A017FIS

      Disengage the 5 claws and remove the reclining remote control bezel LH.

  45. Click here

    REMOVE ROPE HOOK ASSEMBLY (for LH Side)


    1. A017FLCE01

      for Front Side:


      1. Using a screwdriver, disengage the 2 claws.

        Tip:

        Tape the screwdriver tip before use.

      2. Remove the bolt and the rope hook assembly.

    2. A017B9EE01

      for Rear Side:


      1. Using a screwdriver, disengage the 2 claws.

        Tip:

        Tape the screwdriver tip before use.

      2. Remove the bolt and rope hook assembly.

  46. Click here

    REMOVE NO. 2 DECK SIDE TRIM HOOK


    1. A017CPF

      Remove the screw and the No. 2 deck side trim hook.

  47. Click here

    REMOVE FRONT DECK SIDE TRIM COVER LH


    1. A017C3ZE01

      Using a screwdriver, disengage the 4 claws and remove the 2 front deck side trim covers LH.

      Tip:

      Tape the screwdriver tip before use.

  48. Click here

    DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH


    1. A017BD8

      Remove the bolt and disconnect the shoulder anchor of the rear No. 1 seat outer belt assembly.

    2. A017EAE

      Remove the 2 bolts and rear No. 1 seat outer belt assembly.

  49. Click here

    REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Remove the 2 bolts.

    2. Remove the 2 clips.

    3. A017FE0

      Disengage the 7 claws and 4 clips, and remove the deck trim side panel assembly LH.

  50. Click here

    REMOVE QUARTER PILLAR GARNISH LH


    1. A017DVD

      Disengage the 2 claws and 2 guides, and remove the No. 1 seat outer belt guide.

    2. A017B6M

      Disengage the 2 clips and the 2 guides, and remove the quarter pillar garnish LH.

  51. Click here

    REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH (w/o Power Back Door)


    1. w/o Rear No. 2 Seat:


      1. A017ES0

        Remove the bolt.

      2. Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.

    2. w/ Rear No. 2 Seat:


      1. A017DAD

        Disengage the 2 claws and 2 guides, and remove the rear No. 2 seat outer belt guide.

      2. A017FTJ

        Remove the bolt.

      3. Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.

  52. Click here

    REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH (w/ Power Back Door)


    1. w/o Rear No. 2 Seat:


      1. A017E6D

        Remove the bolt.

      2. Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.

    2. w/ Rear No. 2 Seat:


      1. A017DAD

        Disengage the 2 claws and 2 guides, and remove the rear No. 2 seat outer belt guide.

      2. A017EMC

        Remove the bolt.

      3. Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.

  53. Click here

    REMOVE DOOR CONTROL RECEIVER


    1. A017CPP

      Disconnect the connector.

    2. Remove the bolt and the door control receiver.