REAR DOOR LOCK INSTALLATION


  1. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY


    1. A017D8W

      Install the rear door inside locking cable assembly.

    2. A017EZ1

      Engage the 3 claws.

  2. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    1. A017EHD

      Install the rear door lock remote control cable assembly.

    2. A017FSJ

      Engage the claw.

  3. INSTALL REAR DOOR LOCK ASSEMBLY

    Note


    • When reusing the removed rear door lock assembly, replace the door lock wiring harness seal on the connector with a new one.

    • Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.

    • Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion to the connection. This may result in a malfunction of the rear door lock assembly.


    1. Apply MP grease to the sliding parts of the rear door lock assembly.

    2. Install a new door lock wiring harness seal to the rear door lock assembly.

    3. A017EWV

      Insert the rear door lock assembly to the rear door outside handle release plate, and set it to the rear door panel.

    4. Make sure that the rear door outside handle frame release plate is securely connected to the rear door lock assembly.

    5. Using a "TORX" socket wrench (T30), install the rear door lock assembly with the 3 screws.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

    6. Connect the connector.

  4. INSTALL REAR DOOR GLASS RUN


    1. A017BMF

      Install the rear door glass run.

  5. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    1. A017B5Q

      Slide the rear door glass sub-assembly to install it as shown in the illustration.

  6. INSTALL REAR DOOR QUARTER WINDOW GLASS


    1. Install the rear door quarter window glass to the rear door quarter window weatherstrip.

    2. A017G2W

      Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.

  7. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    1. Insert the rear door window division bar sub-assembly from above.

    2. Install the rear door glass run to the rear door lower window frame sub-assembly.

    3. A017ECI

      Install the rear door window division bar sub-assembly with the 2 bolts and screw.

    4. A017FHT

      Install the rear door vent seal.

  8. INSTALL REAR DOOR WEATHERSTRIP


    1. A017B9B

      Engage the 19 clips and install the rear door weatherstrip.

  9. INSTALL REAR DOOR SERVICE HOLE COVER


    1. Apply butyl tape to the rear door panel.

    2. A017FALE01

      Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.

    3. Attach the rear door service hole cover according to the reference points on the rear door panel.

      Note

      Securely install the rear door service hole cover avoiding wrinkles and air bubbles.

    4. Connect the connector.

  10. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP


    1. A017B79

      Install the rear door inner glass weatherstrip.

  11. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. A017CXI

      Connect the rear door lock remote control cable and rear door inside locking cable to the rear door inside handle sub-assembly.

    2. Engage the 2 clamps.

    3. A017GAC

      Engage the rear door trim board with the 5 claws on the rear door inner glass weatherstrip.

    4. Engage the 9 clips and install the rear door trim board to the rear door panel.

    5. A017F2KE01

      Install the 2 screws <B>.

    6. Install the screw <A>.

      Torque:
      3.5 N*m  { 36 kgf*cm, 31 in.*lbf }

  12. INSTALL DOOR ASSIST GRIP COVER


    1. A017C7J

      Engage the 4 claws and install the door assist grip cover.

  13. INSTALL REAR DOOR ARMREST UPPER BASE PANEL


    1. Connect the connector.

    2. A017DAJ

      Engage the 6 claws and 2 clips and install the rear door armrest upper base panel.

  14. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. A017ERK

      Engage the 3 claws to install the rear door inside handle bezel plug.

  15. CONNECT BATTERY NEGATIVE TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.