REAR DOOR LOCK REMOVAL


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait for 90 seconds after disconnecting the terminal to prevent airbag deployment Click here.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. A017F1XE01

      Using a screwdriver with the tip wrapped with protective tape, disengage the 3 claws and remove the rear door inside handle bezel plug.

  3. REMOVE REAR DOOR ARMREST UPPER BASE PANEL


    1. A017EWNE01

      Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws and 2 clips, and remove the rear door armrest upper base panel.

    2. Disconnect the connector.

  4. REMOVE DOOR ASSIST GRIP COVER


    1. A017D3PE01

      Using a screwdriver with the tip wrapped with protective tape, disengage the 4 claws and remove the door assist grip cover.

  5. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. A017F2K

      Remove the 3 screws.

    2. A017GAC

      Using a clip remover, disengage the 9 clips.

    3. Disengage the 5 claws and separate the rear door trim board sub-assembly from the rear door inner glass weatherstrip.

    4. A017EA4

      Disengage the 2 clamps.

    5. Disconnect the front door lock remote control cable and rear door inside locking cable.

  6. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP


    1. A017B79

      Remove the rear door inner glass weatherstrip from the rear door panel.

  7. REMOVE REAR DOOR SERVICE HOLE COVER


    1. A017D47

      Disconnect the connector.

    2. Remove the rear door service hole cover.

      Tech Tips

      Remove the remaining tape on the door.

  8. REMOVE REAR DOOR WEATHERSTRIP


    1. A017B9B

      Using a clip remover, disengage the 19 clips and remove the rear door weatherstrip.

  9. REMOVE REAR DOOR GLASS RUN


    1. A017BMF

      Remove the rear door glass run.

  10. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    1. A017FHT

      Remove the rear door vent seal.

    2. A017ECI

      Remove the 2 bolts, screw, and the rear door window division bar sub-assembly.

  11. REMOVE REAR DOOR QUARTER WINDOW GLASS


    1. A017E81

      Remove the rear door quarter window glass and the rear door quarter window weatherstrip as a unit as shown in the illustration.

    2. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.

  12. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    1. A017F6A

      Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

      Note

      Do not damage the door glass.

  13. REMOVE REAR DOOR LOCK ASSEMBLY


    1. A017FJ9

      Using a "TORX" socket wrench (T30), remove the 3 screws.

    2. Move the rear door lock assembly downward and pull the release plate out of the rear door outside handle frame.

    3. Remove the door lock wiring harness seal from the rear door lock assembly.

  14. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    1. A017FSJ

      Using a screwdriver, disengage the claw.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A017EHD

      Remove the rear door lock remote control cable assembly.

  15. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY


    1. A017EZ1

      Using a screwdriver, disengage the 3 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A017D8W

      Remove the rear door inside locking cable assembly.