FRONT DOOR LOCK INSTALLATION


  1. INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY


    1. A017EO8

      Install the front door inside locking cable assembly.

    2. A017DWV

      Engage the 3 claws.

  2. INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    1. A017EEK

      Install the front door lock remote control cable assembly.

  3. INSTALL FRONT DOOR LOCK ASSEMBLY

    Note


    • When reusing the removed front door lock assembly, replace the door lock wiring harness seal on the connector with a new one.

    • Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.

    • Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion to the connection. This may result in a malfunction of the front door lock assembly.


    1. Apply MP grease to the sliding parts of the front door lock assembly.

    2. Install a new door lock wiring harness seal to the front door lock assembly.

    3. A017CDC

      Insert the front door lock open rod to the front door lock assembly.

    4. Make sure that the front door lock open rod is securely connected to the front door lock assembly.

    5. Using a "TORX" socket wrench (T30), install the front door lock assembly with the 3 screws.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  4. INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)


    1. A017C72

      Engage the 2 claws to install the front door outside handle cover to the front door lock cylinder.

    2. A017C62

      Install the front door lock cylinder.

      Tech Tips

      Make sure that the front door lock cylinder rod is inserted into the front door lock assembly.

    3. A017ETC

      Using a "TORX" socket wrench (T30), install the front door lock cylinder with the screw.

      Torque:
      4.0 N*m  { 41 kgf*cm, 35 in.*lbf }

    4. Install the hole plug.

  5. INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)


    1. A017G5T

      Using a "TORX" socket wrench (T30), install the front door lock cylinder with the screw.

      Torque:
      4.0 N*m  { 41 kgf*cm, 35 in.*lbf }

    2. Install the hole plug.

  6. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY


    1. A017D01

      Install the front door rear lower frame sub-assembly with the bolt.

  7. INSTALL FRONT DOOR GLASS RUN


    1. A017BGI

      Install the front door glass run.

  8. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY


    1. A017CPJE01

      Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated in the order of the arrows in the illustration.

    2. A017FOD

      Install the front door glass sub-assembly with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
    3. A017E3V

      Install the hole plug.

  9. INSTALL FRONT DOOR SERVICE HOLE COVER


    1. Apply butyl tape to the front door panel.

    2. Pass the front door lock remote control cable and rear door inside the locking cable through a new front door service hole cover.

    3. A017G5FE01

      Attach the front door service hole cover according to the reference points on the front door panel.

      Note

      Securely install the front door service hole cover avoiding wrinkles and air bubbles.

    4. A017DHL

      Connect each connector.

    5. Engage the 2 clamps.

  10. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP


    1. A017ESJ

      Install the front door inner glass weatherstrip.

  11. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. Connect the connector.

    2. A017F3J

      Connect the front door lock remote control cable and front door inside locking cable to the front door inside handle sub-assembly.

    3. Engage the 2 clamps.

    4. A017FU9

      Engage the front door trim board with the 5 claws on the front door inner glass weatherstrip.

    5. Engage the 9 clips.

    6. A017FDZE01

      Install the 2 screws <B>.

    7. Install the screw <A> and front door trim board to the front door panel.

      Torque:
      3.5 N*m  { 36 kgf*cm, 31 in.*lbf }

  12. INSTALL COURTESY LIGHT ASSEMBLY


    1. Connect the connector.

    2. A017CHJ

      Engage the claw and install the courtesy light assembly.

  13. INSTALL ASSIST GRIP COVER


    1. A017EGS

      Engage the 4 claws and install the assist grip cover.

  14. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. A017ERK

      Engage the 3 claws and install the front door inside handle bezel plug.

  15. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH


    1. A017CI2

      Engage the clip and claw, and install the front door lower frame bracket garnish.

  16. CONNECT NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.