Click here

SMART ENTRY AND START SYSTEM Room Oscillator does not Recognize Key

Click here
Click here
DTC Code DTC Name
  Room Oscillator does not Recognize Key
Click here

DESCRIPTION

If the room oscillator does not recognize a key, either of the following may be the cause: 1) communication between the indoor electrical key oscillator (front) and electrical key transmitter cannot be performed; or 2) communication between the indoor electrical key oscillator (center) and electrical key transmitter cannot be performed; or 3) communication between the indoor electrical key oscillator (rear) and electrical key transmitter cannot be performed.

Click here

WIRING DIAGRAM

Click here

INSPECTION PROCEDURE

Note:

  • Before performing the inspection, check that there are no problems related to "CAN COMMUNICATION SYSTEM" and "LIN COMMUNICATION SYSTEM".

  • When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the vehicle, and turn a courtesy light switch on and off at 1.5-second intervals until communication between the tester and vehicle begins.

Click here

PROCEDURE


  1. Click here

    CHECK SMART ENTRY AND START SYSTEM (ENTRY FUNCTION)


    1. Check that entry lock and unlock functions can be operated at each door.

      OK
      Entry lock and unlock functions operate normally.

  2. Click here

    CHECK SMART ENTRY AND START SYSTEM (START FUNCTION)


    1. A017ENHE01

      Remove the battery of the electrical key transmitter (Click here).

    2. With the brake pedal depressed, face the logo side of the key to the engine switch.

    3. When operating the engine switch, check whether the power source mode changes.

      OK
      Power source mode changes.
      Tip:

      • When the electrical key transmitter cannot be verified even though it is in the start operating range, the engine start check can be performed by removing the transmitter battery from the electrical key transmitter and holding the transmitter against the engine switch.

      • When performing the check, if the power source mode changes, there is a problem with key certification inside the cabin.


  3. Click here

    CHECK WAVE ENVIRONMENT


    1. Install the battery to the electrical key transmitter.

    2. A017DK5E01

      Bring the electrical key transmitter near the indoor electrical key oscillator (front), and perform an engine start check.

      Note:

      If the key is brought within 0.2 m (0.656 ft.) of the indoor electrical key oscillator (front), communication is not possible.

    3. A017E72E01

      Bring the electrical key transmitter near the indoor electrical key oscillator (center), and perform an engine start check.

      Note:

      If the key is brought within 0.2 m (0.656 ft.) of the indoor electrical key oscillator (rear), communication is not possible.

    4. A017D1CE01

      Bring the electrical key transmitter near the indoor electrical key oscillator (rear), and perform an engine start check.

      Note:

      If the key is brought within 0.2 m (0.656 ft.) of the indoor electrical key oscillator (luggage compartment), communication is not possible.

      Tip:

      • When the electrical key transmitter is brought near the indoor electrical key oscillator, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

      • If the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

      OK
      The engine starts.

  4. Click here

    PERFORM KEY DIAGNOSTIC MODE INSPECTION


    1. A017DK5E01

      Diagnostic mode inspection (indoor electrical key oscillator (front))


      1. Connect the intelligent tester to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the tester on.

      4. Enter the following menus:

        Body / Entry & Start / Key Communication Check / Overhead + Front Room.

      5. When the electrical key transmitter is placed on the driver seat or front passenger seat cushion, check that the wireless door lock buzzer sounds.

    2. A017E72E01

      Diagnostic mode inspection (indoor electrical key oscillator (center))


      1. Connect the intelligent tester to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the tester on.

      4. Enter the following menus:

        Body / Entry & Start / Key Communication Check / Overhead + Rear Room.

      5. When the electrical key transmitter is placed on the rear seat cushion, check that the wireless door lock buzzer sounds.

    3. A017D1CE01

      Diagnostic mode inspection (indoor electrical key oscillator (rear))


      1. Connect the intelligent tester to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the tester on.

      4. Enter the following menus:

        Body / Entry & Start / Key Communication Check / Overhead + Back Door (inside).

      5. When the electrical key transmitter is held at the same height as the rear bumper upper surface and aligned with the center of the rear of the vehicle, check that the wireless door lock buzzer sounds.

        Tip:

        If the buzzer sounds, it can be determined that the indoor electrical key oscillators are operating normally.

        Result
        Result Proceed to
        Front, center and rear operation checks are normal or fail A
        Center operation check is normal B
        Rear operation check is normal C
        Front operation check is normal D

  5. Click here

    CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - INDOOR ELECTRICAL KEY OSCILLATOR)


    1. A017G2SE04

      Disconnect the certification ECU (smart key ECU assembly) and indoor electrical key oscillator front connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      D36-11 (CLG5) - N14-1 (CLG3) Always Below 1 Ω
      D36-12 (CG5B) - N14-3 (CLGB) Always Below 1 Ω
      D36-11 (CLG5) - Body ground Always 10 kΩ or higher
      D36-12 (CG5B) - Body ground Always 10 kΩ or higher

  6. Click here

    INSPECT INDOOR ELECTRICAL KEY OSCILLATOR (FRONT)


    1. A017DG6E05

      Measure the voltage according to the value(s) in the table below.

      Standard voltage
      Tester Connection Tool Setting Condition Specified Condition
      D36-11 (CLG5) - D36-12 (CG5B) 2 V/DIV, 2 μs/DIV. (Reference) Engine switch on (IG) Pulse generation

  7. Click here

    CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - INDOOR ELECTRICAL KEY OSCILLATOR)


    1. A017G2SE05

      Disconnect the certification ECU (smart key ECU assembly) and indoor electrical key oscillator center connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      D36-13 (CLG6) - O16-1 (CLG4) Always Below 1 Ω
      D36-14 (CG6B) - O16-3 (CLGB) Always Below 1 Ω
      D36-13 (CLG6) - Body ground Always 10 kΩ or higher
      D36-14 (CG6B) - Body ground Always 10 kΩ or higher

  8. Click here

    INSPECT INDOOR ELECTRICAL KEY OSCILLATOR (CENTER)


    1. A017DG6E06

      Measure the voltage according to the value(s) in the table below.

      Standard voltage
      Tester Connection Tool Setting Condition Specified Condition
      D36-13 (CLG6) - D36-14 (CG6B) 2 V/DIV, 2 μs/DIV. (Reference) Engine switch on (IG) Pulse generation

  9. Click here

    CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - INDOOR ELECTRICAL KEY OSCILLATOR)


    1. A017G2SE06

      Disconnect the certification ECU (smart key ECU assembly) and indoor electrical key oscillator rear connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      D36-15 (CLG7) - N13-1 (CLG6) Always Below 1 Ω
      D36-16 (CG7B) - N13-3 (CLGB) Always Below 1 Ω
      D36-15 (CLG7) - Body ground Always 10 kΩ or higher
      D36-16 (CG7B) - Body ground Always 10 kΩ or higher

  10. Click here

    INSPECT INDOOR ELECTRICAL KEY OSCILLATOR (REAR)


    1. A017DG6E07

      Measure the voltage according to the value(s) in the table below.

      Standard voltage
      Tester Connection Tool Setting Condition Specified Condition
      D36-15 (CLG7) - D36-16 (CG7B) 2 V/DIV, 2 μs/DIV. (Reference) Engine switch on (IG) Pulse generation

  11. Click here

    GO TO SMART ENTRY AND START SYSTEM (Power Source Mode does not Change)Click here

  12. Click here

    AFFECTED BY WAVE INTERFERENCE

  13. Click here

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

  14. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  15. Click here

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

  16. Click here

    GO TO OTHER PROBLEM (PROCEED TO PROBLEM SYMPTOMS TABLE FOR EACH DOOR)Click here

  17. Click here

    REPLACE INDOOR ELECTRICAL KEY OSCILLATOR (FRONT)Click here

  18. Click here

    REPLACE INDOOR ELECTRICAL KEY OSCILLATOR (CENTER)Click here

  19. Click here

    REPLACE INDOOR ELECTRICAL KEY OSCILLATOR (REAR)Click here