WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Smart Entry and Start System) OPERATION CHECK

FUNCTIONS AND OPERATING CONDITIONS

1. The wireless door LOCK/UNLOCK function:

   The wireless door lock control function operates only when the following 3 conditions are met:

   
   

   1. There is no key in the ignition key cylinder.

   2. All the doors are closed.

   3. The power door lock system operates normally.

      Tech Tips

      The UNLOCK function operates even when a door is open.

2. The glass hatch open function:

   The wireless door lock control function operates only when the following 3 conditions are met:

   
   

   1. There is no key in the ignition key cylinder.

   2. The glass hatch is in the fully closed position.

   3. The glass hatch system operates normally.

3. The remote panic function (for RHD):

   The wireless door lock control function operates only when the following condition is met:

   
   

   1. The ignition key is turned off.

      Tech Tips

      The key can be inserted, however it must be in the off position.

4. The wireless transmitter operational range differs depending on the situation.

   
   

   1. The operational range differs depending on the user, the way the transmitter is held, and the location.

   2. In certain areas, the operational range will be reduced due to the vehicle body shape and the influence of the surrounding environment.

   3. Since the transmitter uses weak radio waves, the operational range may be reduced or the transmitter may not function if interference or stronger radio waves occur in the area where the transmitter is used.

   4. When the battery is low, the operational range is reduced and/or the transmitter may not function.

      Tech Tips

      If the transmitter has been left in a place that is exposed to direct sunlight, such as on the instrument panel, the battery may be weakened or other problems may occur.

CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS

1. Establish conditions that allow the wireless control function to be operated successfully.

2. Check basic functions.

   
   

   1. Check whether the LED of the transmitter illuminates 3 times when each switch is pressed 3 times.

      Tech Tips

      If the LED does not illuminate when the switch has been pressed 3 times or more, it may have a dead battery.

   2. Check that all the doors lock when the LOCK switch is pressed.

   3. Check that all the doors unlock when the UNLOCK switch is pressed.*

      *: for RHD

   4. Check that the driver side door unlock when the UNLOCK switch is pressed once, and unlocks all doors when pressed twice within 3 seconds.*

      *: for LHD

   5. Check that the glass hatch opens when the GLASS HATCH switch is held down for 0.8 seconds.

3. Check the chattering prevention function.

   
   

   1. Check that the corresponding operation occurs only once and is not repeated continuously while the switch is held. However, when the switch is operated repeatedly at 1 second intervals, check that the corresponding operation is carried out.

4. Check the automatic lock function.

   
   

   1. Check that if all doors are unlocked with the UNLOCK switch and none of the doors is opened or locked within approximately 30 seconds, the doors automatically re-lock.

   2. Check that if all doors are unlocked with the UNLOCK switch and a door is opened or locked within approximately 30 seconds, the automatic lock function does not operate.

5. Check the switch operation fail-safe function.

   
   

   1. Check that the doors cannot be locked or unlocked by operating a switch on the unregistered transmitter, and that the doors are locked and unlocked by operating a switch on the registered transmitter.

6. Check the door ajar warning function.

   
   

   1. Check that the wireless door lock buzzer sounds for approximately 10 seconds when the LOCK switch is pressed with any of the doors ajar or open.

7. Check the repeat function.

   
   

   1. Check that all the doors attempt to automatically lock once again 1 second after the LOCK switch has been pressed while the movement of the driver side door control knob, which is in the unlocked state, is being restricted.

8. Check the answer-back function.

   
   

   1. When the LOCK switch is pressed, check that the lights flash once and the buzzer^*sounds once, simultaneously with the locking operation of all the doors.

      Tech Tips

      
      

      • *: for RHD

   2. When the UNLOCK switch is pressed once, check that the lights flash twice and the buzzer^*sounds twice, simultaneously with the unlocking operation of all the doors.

      Tech Tips

      
      

      • *: for RHD

   3. When the GLASS HATCH OPEN switch is held down for 0.8 seconds or more, check that the buzzer sounds^*once, simultaneously with the opening operation of the glass hatch.

      Tech Tips

      
      

      • *: for RHD

9. Check the remote panic function (for RHD).

   
   

   1. Check that the horn sounds, the headlights and taillights flash and the interior light remains on (when the light switch is turned to the DOOR position) for 30 seconds by the theft alarm function, when the PANIC switch is held down for 0.8 seconds or more. Also, check that the horn stops sounding and the lights stop flashing when either switch of the transmitter is pressed.

10. Check the interior light ON function.

    Tech Tips

    Turn the interior light switch to the DOOR position before the check.

    
    

    1. Check that the interior light comes on simultaneously with the unlocking operation when the UNLOCK switch has been pressed.

    2. Check that the interior light goes off in approximately 15 seconds if none of the doors are opened after the unlocking operation.