REAR WIPER MOTOR INSTALLATION

PRECAUTION

INSTALL REAR WIPER MOTOR ASSEMBLY (for Fixed Glass Type)

1. 

   Install the rear wiper motor assembly with the 4 bolts.

   5.5 N*m

   56 kgf*cm

   49 in.*lbf

   Note:

   Be careful not to scratch the back door glass.

2. Connect the connector.

INSTALL REAR WIPER MOTOR ASSEMBLY (for Glass Hatch Type)

1. 

   Temporarily install the rear wiper motor assembly with the 4 bolts and 2 nuts.

   Note:
   

   • Do not hold the rear wiper motor assembly by the rear wiper link pivot.

   • Be careful not to scratch the back door glass.

   • Do not remove the centering jig before installing the rear wiper link pivot.

2. Tighten the 4 bolts and 2 nuts in the order shown in the illustration to install the rear wiper motor assembly.

   Bolt
   5.5 N*m	56 kgf*cm	49 in.*lbf
   Nut
   8.0 N*m	82 kgf*cm	71 in.*lbf

3. Connect the connector.

INSTALL REAR WIPER MOTOR GROMMET (for Fixed Glass Type)

1. 

   Apply MP grease to the entire surface of the wiper motor grommet lip.

   Tip:

   Make sure that the hole does not clog with grease and the grooves on the lip are filled with grease.

2. 

   Install the rear wiper motor grommet.

   Tip:

   As shown in the illustration, install the rear wiper motor grommet with its position mark at the top.

INSTALL REAR WIPER LINK PIVOT (for Glass Hatch Type)

1. 

   Install the rear wiper link pivot with the nut.

   7.0 N*m

   71 kgf*cm

   62 in.*lbf

2. Open the glass hatch.

3. 

   Disengage the 2 guides.

4. Disengage the 3 claws and remove the centering jig.

5. Close the glass hatch.

INSTALL REAR WIPER LINK CAP (for Glass Hatch Type)

1. 

   Apply MP grease to the entire surface of the rear wiper link cap.

   Tip:

   Make sure that the hole does not get clogged with grease and the grooves on the lip are filled with grease.

2. 

   Install the rear wiper link cap.

INSTALL REAR WIPER ARM AND BLADE ASSEMBLY (for Fixed Glass Type)

1. Stop the wiper motor at the automatic stop position.

2. 

   When reinstalling:

   
   

   1. Clean the wiper arm serrations.

   2. Clean the wiper pivot serrations with a wire brush.

3. 

   Place the rear wiper arm and blade assembly so that the rear wiper blade is aligned with the ceramic line.

   Area	Dimension
   A	10 mm (0.39 in.)

4. Install the rear wiper arm and blade assembly with the nut.

   5.5 N*m

   56 kgf*cm

   49 in.*lbf

   Tip:

   Hold down the wiper arm by hand when tightening the nut.

INSTALL REAR WIPER ARM AND BLADE ASSEMBLY (for Glass Hatch Type)

1. Stop the wiper motor at the automatic stop position.

2. 

   When reinstalling:

   
   

   1. Clean the wiper arm serrations.

   2. Clean the wiper pivot serrations with a wire brush.

3. 

   Place the rear wiper arm and blade assembly so that the rear wiper blade is aligned with the ceramic line.

   Area	Dimension
   A	10 mm (0.39 in.)

4. Install the rear wiper arm and blade assembly with the nut.

   5.5 N*m

   56 kgf*cm

   49 in.*lbf

   Tip:

   Hold down the wiper arm by hand when tightening the nut.

INSTALL REAR WIPER ARM HEAD CAP

1. 

   Install the rear wiper arm head cap.

   Tip:

   Push down on the cap until a click sound can be heard.

INSTALL REAR WIPER SHAFT COVER (for Glass Hatch Type)

1. Open the glass hatch.

2. 

   Engage the 3 clips and install the rear wiper shaft cover.

3. Operate the rear wiper while spraying washer fluid on the glass. Make sure that the rear wiper functions properly and there is no interference with the vehicle body.