REAR COMBINATION LIGHT ASSEMBLY INSTALLATION

INSTALL REAR BUMPER ASSEMBLY

1. w/ Rear Fog Light:

   
   

   1. Connect the rear fog light connector.

2. 

   Engage the 7 claws and install the rear bumper assembly.

   Tip:

   Use the same procedure for the RH side and LH side.

3. 

   Install the 5 clips, 2 screws and 2 bolts.

4. 

   Install the 2 screws.

   Tip:

   Use the same procedure for the RH side and LH side.

INSTALL REAR QUARTER PANEL MUDGUARD LH

1. 

   Install the 2 screws (A).

2. Using a 4 mm hexagon wrench, install the 3 screws (B).

INSTALL REAR QUARTER PANEL MUDGUARD RH

INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH (w/o Power Back Door)

1. w/ Rear No. 2 Seat:

   
   
   1. 

      Engage the 2 guides and 5 clips.

   2. Install the roof side inner garnish assembly LH with the bolt.

   3. 

      Engage the 2 guides and 2 claws, and install the No. 2 seat outer belt guide.

2. w/o Rear No. 2 Seat:

   
   
   1. 

      Engage the 2 guides and 5 clips.

   2. Install the roof side inner garnish assembly LH with the bolt.

INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH (w/ Power Back Door)

1. w/ Rear No. 2 Seat:

   
   
   1. 

      Engage the 2 guides and 5 clips.

   2. Install the roof side inner garnish assembly LH with the bolt.

   3. 

      Engage the 2 guides and 2 claws, and install the No. 2 seat outer belt guide.

2. w/o Rear No. 2 Seat:

   
   
   1. 

      Engage the 2 guides and 5 clips.

   2. Install the roof side inner garnish assembly LH with the bolt.

INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

1. Engage the 4 clips and 7 claws.

2. Install the 2 clips.

3. 

   Install the deck trim side panel assembly LH with the 2 bolts.

CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH

1. 

   Connect the floor anchor end of the rear No. 1 seat outer belt assembly and install the bolt.

   42 N*m

   428 kgf*cm

   31 ft.*lbf

   Note:

   Do not allow the anchor part of the rear No. 1 seat outer belt assembly to overlap the protruding part of the floor panel.

INSTALL FRONT DECK SIDE TRIM COVER LH

1. 

   Engage the 4 claws and install the 2 front deck side trim covers LH.

INSTALL NO. 2 DECK SIDE TRIM HOOK

1. 

   Install the No. 2 deck side trim hook with the screw.

INSTALL ROPE HOOK ASSEMBLY (for LH Side)

1. 

   for Front Side:

   
   

   1. Install the rope hook assembly with the bolt.

      6.5 N*m

      66 kgf*cm

      58 in.*lbf

   2. Engage the 2 claws.

2. 

   for Rear Side:

   
   

   1. Install the rope hook assembly with the bolt.

      6.5 N*m

      66 kgf*cm

      58 in.*lbf

   2. Engage the 2 claws.

INSTALL REAR DECK TRIM COVER (w/o Remote Folding Function)

1. 

   Engage the 10 claws to install the rear deck trim cover.

INSTALL RECLINING REMOTE CONTROL BEZEL LH (w/ Remote Folding Function)

1. 

   Engage the 5 claws to install the reclining remote control lever bezel LH.

INSTALL REAR POWER OUTLET SOCKET COVER

1. 

   Engage the 2 claws and install the rear power outlet socket cover.

INSTALL REAR POWER POINT SOCKET ASSEMBLY

1. 

   Engage the claw and install the rear power point socket assembly.

2. Connect the connector.

INSTALL REAR COMBINATION LIGHT SERVICE COVER LH

1. 

   Engage the 2 guides and 6 claws, and install the rear combination light service cover LH.

INSTALL SIDE TRIM COVER LH

1. 

   Engage the 10 claws and install the side trim cover LH.

INSTALL DECK SIDE TRIM LH

1. 

   Engage the 3 guides and 4 claws as shown in the illustration.

2. 

   Install the deck side trim LH with the bolt.

INSTALL DECK SIDE TRIM COVER NO.2

1. 

   Engage the 2 claws and install the deck side trim cover LH.

INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH (w/o Rear No. 2 Seat)

INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH (w/ Rear No. 2 Seat)

INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

1. Engage the 4 clips and 7 claws.

2. Install the 2 clips.

3. 

   Install the deck trim side panel assembly RH with the 3 bolts.

CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH

INSTALL FRONT DECK SIDE TRIM COVER RH

INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

INSTALL ROPE HOOK ASSEMBLY (for RH Side)

INSTALL REAR COMBINATION LIGHT SERVICE COVER RH

1. 

   Engage the 2 guides and 6 claws, and install the rear combination light service cover RH.

INSTALL REAR ROOM TEMPERATURE SENSOR (w/ Rear Automatic Air Conditioning System)

1. Connect the connector.

2. 

   Engage the 4 claws and install the rear room temperature sensor.

INSTALL SIDE TRIM COVER RH (w/o Rear Automatic Air Conditioning System)

1. 

   Engage the 4 claws, and install the side trim cover RH.

INSTALL DECK SIDE TRIM RH

INSTALL DECK SIDE TRIM COVER NO.1

INSTALL REAR SEAT SIDE GARNISH CAP (w/o Rear Air Conditioning System)

1. 

   Engage the guide and 8 claws, and install the rear seat side garnish cap.

INSTALL REAR SEAT SIDE GARNISH CAP (w/ Rear Air Conditioning System)

1. 

   Engage the guide and 6 claws.

2. Install the rear seat side garnish cap with the screw.

INSTALL REAR FLOOR FINISH PLATE

1. 

   Engage the 4 clips and 4 claws, and install the rear floor finish plate.

INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)

1. 

   Install the 6 bolts on the rear of the seat.

   37 N*m

   377 kgf*cm

   27 ft.*lbf

2. 

   Install the rear No. 2 seat assembly with the bolt.

   37 N*m

   377 kgf*cm

   27 ft.*lbf

INSTALL REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH (w/ Rear No. 2 Seat)

1. 

   Route the rear No. 2 seat outer belt assembly LH through the rubber band as shown in the illustration.

   Table 1. Text in Illustration

   *1	Rubber Band

2. Install the rear No. 2 seat outer belt assembly LH with the bolt.

   42 N*m

   428 kgf*cm

   31 ft.*lbf

   Note:

   After installing the belt, check that it is not twisted.

INSTALL REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH (w/ Rear No. 2 Seat)

INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat)

1. Install the rear No. 2 seat inner belt assembly with the bolt.

   42 N*m

   428 kgf*cm

   31 ft.*lbf

   Tip:

   Use the same procedure for the RH side and LH side.

INSTALL REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)

1. 

   Install the rear deck floor box with the 2 nuts.

INSTALL DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)

1. 

   Install the 2 nuts and deck floor board assembly.

2. Engage the 3 claws.

INSTALL REAR MAT

1. 

   Install the rear mat.

INSTALL DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)

1. 

   Install the rear deck floor board assembly with the 4 nuts and 4 bolts.

INSTALL DECK SIDE TRIM BOX LH

1. 

   Install the deck side trim box LH as shown in the illustration.

2. 

   Install the 2 deck side trim clips and clip.

INSTALL REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)

1. 

   Engage the 2 clips and install the rear seat side cover LH.

INSTALL DECK SIDE TRIM BOX RH

1. 

   Install the deck side trim box RH as shown in the illustration.

2. 

   Install the 2 deck side trim clips and clip.

INSTALL JACK CARRIER ASSEMBLY (for LHD)

1. 

   Engage the 3 claws, and install the jack carrier assembly.

INSTALL JACK CARRIER ASSEMBLY (for RHD)

1. 

   Engage the 3 claws, and install the jack carrier assembly.

INSTALL JACK ASSEMBLY (for LHD)

1. 

   Install the jack assembly.

INSTALL JACK ASSEMBLY (for RHD)

1. 

   Install the jack assembly.

INSTALL JACK CARRIER CUSHION (for LHD)

1. 

   Install the jack carrier cushion.

INSTALL JACK CARRIER CUSHION (for RHD)

1. 

   Install the jack carrier cushion.

INSTALL REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)

1. 

   Engage the 2 clips and install the rear seat side cover RH.

INSTALL REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)

1. 

   Engage the 3 guides and 3 clips and install the rear No. 1 floor board.

INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

1. Install the tonneau cover assembly.

INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY

1. 

   Engage the 2 guides and install the No. 2 deck board sub-assembly.

INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY

1. 

   Engage the 2 guides and install the No. 3 deck board sub-assembly.

INSTALL DECK BOARD ASSEMBLY

1. 

   Install the deck board assembly.

INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

1. 

   Align the alignment mark (red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

   Note:

   After installation, check that the corners fit correctly.

INSTALL REAR DOOR SCUFF PLATE LH

1. 

   Engage the guide, 3 clips and 5 claws, and install the rear door scuff plate LH.

INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

1. 

   Align the alignment mark (green) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.

   Note:

   After installation, check that the corners fit correctly.

INSTALL REAR DOOR SCUFF PLATE RH