Click here

HIGH MOUNTED STOP LIGHT ASSEMBLY (for Rear Spoiler without Press Line) REMOVAL

Click here
Click here
  1. Click here

    PRECAUTION

    Note:

    • Be sure to use the centering jig when removing and installing the rear wiper motor assembly (for Glass Hatch Type). Failure to do so will result in a change of the location of the axis of the rear wiper motor assembly (for Glass Hatch Type), causing the wiping angle to change.

    • After installing the rear wiper motor assembly (for Glass Hatch Type), do not open the glass hatch before installing the rear wiper link pivot.

    • If the rear wiper motor assembly is removed without using the centering jig, the rear wiper motor assembly must be replaced with a new one.

  2. Click here

    REMOVE BACK WINDOW UPPER TRIM PANEL ASSEMBLY


    1. A017EYI

      Disengage the 4 clips and 4 claws, and remove the back window upper trim panel assembly.

  3. Click here

    REMOVE BACK DOOR TRIM COVER LH (w/o Power Back Door)


    1. A017BOQ

      Disengage the 2 clips and 2 claws, and remove the back door trim cover LH.

  4. Click here

    REMOVE BACK DOOR SERVICE HOLE COVER LH (w/ Power Back Door)


    1. A017ECX

      Disengage the 6 claws, and remove the back door service hole cover LH.

  5. Click here

    DISCONNECT POWER BACK DOOR ROD (w/ Power Back Door)


    1. A017F50

      Disconnect the power back door rod and remove the back door stay plate.

  6. Click here

    REMOVE BACK DOOR TRIM COVER LH (w/ Power Back Door)


    1. A017ERC

      Disengage the 2 clips and 2 claws, and remove the back door trim cover LH.

  7. Click here

    REMOVE BACK DOOR TRIM COVER RH


    1. A017D6U

      Disengage the 2 clips and 2 claws, and remove the back door trim cover RH.

  8. Click here

    REMOVE BACK DOOR LOCK COVER (for Glass Hatch Type)


    1. A017G02

      Disengage the 2 claws and 4 guides, and remove the back door lock cover.

  9. Click here

    REMOVE ASSIST STRAP HOLE COVER


    1. A017CPS

      Disengage the 2 claws and 2 guides, and remove the assist strap hole cover.

  10. Click here

    REMOVE ASSIST STRAP ASSEMBLY


    1. A017FJZ

      Remove the bolt and assist strap assembly.

  11. Click here

    REMOVE BACK DOOR TRIM PANEL ASSEMBLY


    1. A017CKT

      Disengage the 16 clips and remove the back door trim panel assembly.

  12. Click here

    REMOVE REAR WIPER SHAFT COVER (for Glass Hatch Type)


    1. A017G4Z

      Disengage the 3 clips and remove the rear wiper shaft cover.

  13. Click here

    REMOVE REAR WIPER ARM HEAD CAP


    1. A017DOH

      Remove the rear wiper arm head cap.

  14. Click here

    REMOVE REAR WIPER ARM AND BLADE ASSEMBLY


    1. A017BYQ

      Remove the nut and the rear wiper arm and blade assembly.

  15. Click here

    REMOVE REAR WIPER MOTOR GROMMET (for Fixed Glass Type)


    1. A017DID

      Remove the rear wiper motor grommet.

  16. Click here

    REMOVE REAR WIPER LINK CAP (for Glass Hatch Type)


    1. A017ESU

      Remove the rear wiper link cap.

  17. Click here

    REMOVE REAR WIPER LINK PIVOT (for Glass Hatch Type)


    1. A017CYL

      Remove the nut and the rear wiper link pivot.

  18. Click here

    REMOVE REAR WIPER MOTOR ASSEMBLY (for Fixed Glass Type)


    1. A017COW

      Disconnect the connector.

    2. Remove the 4 bolts and the rear wiper motor assembly.

      Note:

      Be careful not to scratch the back door glass.

  19. Click here

    REMOVE REAR WIPER MOTOR ASSEMBLY (for Glass Hatch Type)


    1. When reinstalling the rear wiper motor assembly:


      1. Open the glass hatch.

      2. A017B51

        Engage the 3 claws and 2 guides, and then install the centering jig.

        Note:

        • The centering jig cannot be reused.

        • Do not remove the centering jig before installing the rear wiper link pivot.

      3. A017EGY

        Close the glass hatch, and engage the 2 claws and guide.

        Note:

        Be sure to engage the 2 claws and guide securely.

      4. A017CCB

        Disconnect the connector.

      5. Remove the 2 nuts.

      6. Remove the 4 bolts and the rear wiper motor assembly.

        Note:

        • Do not hold the rear wiper motor assembly by the rear wiper link pivot.

        • Be careful not to scratch the back door glass.

    2. When using a new rear wiper motor assembly:


      1. A017ET9

        Disconnect the connector.

      2. Remove the 4 bolts.

      3. A017FDH

        Remove the 2 nuts and the rear wiper motor assembly.

        Note:

        Be careful not to scratch the back door glass.

  20. Click here

    REMOVE BACK DOOR GLASS GUIDE BRACKET SUB-ASSEMBLY (for Fixed Glass Type)


    1. A017D4LE01

      Loosen the bolt <A>.

      Note:

      Bolt <A> cannot be removed from the back door glass guide bracket sub-assembly.

    2. Remove the 3 bolts <B>.

    3. A017CE4

      Disengage the clip and remove the back door glass guide bracket sub-assembly.

  21. Click here

    REMOVE REAR SPOILER SUB-ASSEMBLY


    1. A017B1AE01

      Put protective tape around the rear spoiler sub-assembly.

    2. Disconnect the wire harness.

      Note:

      Do not allow the disconnected wire harness to get caught between the back door and the vehicle body to prevent it from being damaged.


      1. A017C3J

        Turn back the wire harness grommet.

      2. Disengage the 4 claws and pull out the wire harness from the vehicle.

        Note:

        Do not forcefully pull out the wire harness.

      3. A017EDG

        Disconnect the 2 connectors.

      4. Disconnect the rear washer hose.

      5. A017E9T

        Disengage the grommet.

      6. Disconnect the connector.

    3. Using a "TORX" socket wrench (T30), remove the 2 screws (A).

    4. A017E0HE01

      Using a "TORX" socket wrench (T30), remove the 6 screws (B).

    5. A017EPG

      Disengage the 2 claws.

    6. A017D23

      Raise and lower the glass hatch and the back door respectively. Pull out the wire harness from the vehicle and remove the rear spoiler sub-assembly.

  22. Click here

    REMOVE CENTER STOP LIGHT ASSEMBLY


    1. A017EI8

      Remove the 2 screws.

    2. Disconnect the center stop light assembly from the rear spoiler sub-assembly.

    3. Disconnect the connector and remove the center stop light assembly.