Click here

LIGHTING SYSTEM Front Fog Light Circuit

Click here
Click here
DTC Code DTC Name
  Front Fog Light Circuit
Click here

DESCRIPTION

The main body ECU controls the front fog light relay when a signal is received from the headlight dimmer switch assembly.

Click here

WIRING DIAGRAM

Click here

INSPECTION PROCEDURE

Click here

PROCEDURE


  1. Click here

    PERFORM ACTIVE TEST USING INTELLIGENT TESTER


    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on (IG).

    3. Turn the intelligent tester on.

    4. Select the following menu items: Body Electrical / Main Body / Active Test.

    5. Check that the relay operates.

      Table 1. Main Body:
      Tester Display Test Part Control Range Diagnostic Note
      Front Fog Light Relay Front fog light relay ON/OFF -
      OK
      Front fog light relay operates. (Front fog lights come on.)

  2. Click here

    INSPECT FUSE (FR FOG)


    1. Remove the FR FOG fuse from the instrument panel junction block.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      FR FOG fuse Always Below 1 Ω

  3. Click here

    INSPECT FOG LIGHT RELAY (FOG)


    1. A017BZ1E87

      Remove the front fog light relay from the instrument panel junction block.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      3 - 5 Voltage is not applied between terminals 1 and 2 10 kΩ or higher
      3 - 5 Apply the battery voltage between terminals 1 and 2 Below 1 Ω

  4. Click here

    CHECK HARNESS AND CONNECTOR (BATTERY - FRONT FOG LIGHT RELAY)


    1. A017FC8E01

      Measure the voltage according to the value(s) in the table below.

      Standard voltage
      Tester Connection Condition Specified Condition
      Front fog light relay terminal 5 - Body ground Always 11 to 14 V
      Front fog light relay terminal 1 - Body ground Light control switch OFF → TAIL Below 1 V → 11 to 14 V

  5. Click here

    CHECK HARNESS AND CONNECTOR (FRONT FOG LIGHT RELAY - MAIN BODY ECU)


    1. A017FU6E03

      Disconnect the D7 main body ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      Front fog light relay terminal 2 - D7-4 (FFGO) Always Below 1 Ω
      D7-4 (FFGO) - Body ground Always 10 kΩ or higher

  6. Click here

    INSPECT MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)


    1. A017DZQE05

      Reconnect the D7 main body ECU connector.

    2. Install the front fog light relay to the instrument panel junction block.

    3. Measure the voltage according to the value(s) in the table below.

      Standard voltage
      Tester Connection Switch Condition Specified Condition
      D7-4 (FFGO) - Body ground Light control switch in HEAD, front fog light switch OFF → ON 11 to 14 V → Below 1 V

  7. Click here

    PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLEClick here

  8. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  9. Click here

    REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)

  10. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR (FRONT FOG LIGHT RELAY - BODY GROUND)

  11. Click here

    REPLACE FUSE

  12. Click here

    REPLACE FOG LIGHT RELAY