REAR NO. 1 SEAT OUTER BELT ASSEMBLY INSTALLATION

INSTALL QUARTER PILLAR GARNISH

1. 

   Engage the 2 guides and the 2 clips, and install the quarter pillar garnish LH as shown in the illustration.

2. 

   Engage the 2 guides and the 2 claws, and install the No. 1 seat outer belt guide.

INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)

1. Engage the 4 clips and 7 claws.

2. Install the 2 clips.

3. 

   Install the deck trim side panel assembly LH with the 2 bolts.

INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)

1. Engage the 4 clips and 7 claws.

2. Install the 2 clips.

3. 

   Install the deck trim side panel assembly RH with the 3 bolts.

INSTALL FRONT DECK SIDE TRIM COVER

1. 

   Engage the 4 claws and install the 2 front deck side trim covers LH.

INSTALL NO. 2 DECK SIDE TRIM HOOK (for LH Side)

1. 

   Install the No. 2 deck side trim hook with the screw.

INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for RH Side)

INSTALL ROPE HOOK ASSEMBLY

1. 

   for Front Side:

   
   

   1. Install the rope hook assembly with the bolt.

      6.5 N*m

      66 kgf*cm

      58 in.*lbf

   2. Engage the 2 claws.

2. 

   for Rear Side:

   
   

   1. Install the rope hook assembly with the bolt.

      6.5 N*m

      66 kgf*cm

      58 in.*lbf

   2. Engage the 2 claws.

INSTALL REAR DECK TRIM COVER (for LH Side without Remote Folding Function)

1. 

   Engage the 10 claws to install the rear deck trim cover.

INSTALL RECLINING REMOTE CONTROL LEVER BEZEL LH (for LH Side with Remote Folding Function)

1. 

   Engage the 5 claws to install the reclining remote control lever bezel LH.

INSTALL REAR POWER OUTLET SOCKET COVER (for LH Side)

1. 

   Engage the 2 claws and install the rear power outlet socket cover.

INSTALL REAR POWER POINT SOCKET ASSEMBLY (for LH Side)

1. 

   Engage the claw and install the rear power point socket assembly.

2. Connect the connector.

INSTALL REAR COMBINATION LIGHT SERVICE COVER LH (for LH Side)

1. 

   Engage the 2 guides and 6 claws, and install the rear combination light service cover LH.

INSTALL REAR COMBINATION LIGHT SERVICE COVER RH (for RH Side)

1. 

   Engage the 2 guides and 6 claws, and install the rear combination light service cover RH.

INSTALL SIDE TRIM COVER RH (for RH Side without Rear Automatic Air Conditioning System)

1. 

   Engage the 4 claws, and install the side trim cover RH.

INSTALL REAR ROOM TEMPERATURE SENSOR (for RH Side with Rear Automatic Air Conditioning System)

1. Connect the connector.

2. 

   Engage the 4 claws and install the rear room temperature sensor.

INSTALL SIDE TRIM COVER LH (for LH Side)

1. 

   Engage the 10 claws and install the side trim cover LH.

INSTALL DECK SIDE TRIM

1. 

   Engage the 3 guides and 4 claws as shown in the illustration.

2. 

   Install the deck side trim LH with the bolt.

INSTALL DECK SIDE TRIM COVER

1. 

   Engage the 2 claws and install the deck side trim cover LH.

INSTALL REAR SEAT SIDE GARNISH CAP (for RH Side without Rear Air Conditioning System)

1. 

   Engage the guide and 8 claws, and install the rear seat side garnish cap.

INSTALL REAR SEAT SIDE GARNISH CAP (for RH Side with Rear Air Conditioning System)

1. 

   Engage the guide and 6 claws.

2. Install the rear seat side garnish cap with the screw.

INSTALL REAR FLOOR FINISH PLATE

1. 

   Engage the 4 clips and 4 claws, and install the rear floor finish plate.

INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)

1. 

   Install the 6 bolts on the rear of the seat.

   37 N*m

   377 kgf*cm

   27 ft.*lbf

2. 

   Install the rear No. 2 seat assembly with the bolt.

   37 N*m

   377 kgf*cm

   27 ft.*lbf

INSTALL CENTER SEAT CUSHION COVER SUB-ASSEMBLY (w/ Rear No. 2 Seat)

1. 

   Engage the 2 claws <B>.

2. Engage the 2 claws <A> to install the center seat cushion cover sub-assembly.

CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH (w/ Rear No. 2 Seat)

1. 

   Route the rear No. 2 seat outer belt assembly LH through the rubber band as shown in the illustration.

   Table 1. Text in Illustration

   *1	Rubber Band

2. Install the rear No. 2 seat outer belt assembly LH with the bolt.

   42 N*m

   428 kgf*cm

   31 ft.*lbf

   Note:

   After installing the belt, check that it is not twisted.

CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH (w/ Rear No. 2 Seat)

INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat)

1. Install the rear No. 2 seat inner belt assembly with the bolt.

   42 N*m

   428 kgf*cm

   31 ft.*lbf

   Tip:

   Use the same procedure for the RH side and LH side.

INSTALL REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)

1. 

   Install the rear deck floor box with the 2 nuts.

INSTALL DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)

1. 

   Install the rear deck floor board assembly with the 4 nuts and 4 bolts.

INSTALL REAR MAT

1. 

   Install the rear mat.

INSTALL DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)

1. 

   Install the 2 nuts and deck floor board assembly.

2. Engage the 3 claws.

INSTALL DECK SIDE TRIM BOX LH

1. 

   Install the deck side trim box LH as shown in the illustration.

2. 

   Install the 2 deck side trim clips and clip.

INSTALL REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)

1. 

   Engage the 2 clips and install the rear seat side cover LH.

INSTALL DECK SIDE TRIM BOX RH

1. 

   Install the deck side trim box RH as shown in the illustration.

2. 

   Install the 2 deck side trim clips and clip.

INSTALL JACK CARRIER ASSEMBLY (for LHD)

1. 

   Engage the 3 claws, and install the jack carrier assembly.

INSTALL JACK CARRIER ASSEMBLY (for RHD)

1. 

   Engage the 3 claws, and install the jack carrier assembly.

INSTALL JACK ASSEMBLY (for LHD)

1. 

   Install the jack assembly.

INSTALL JACK ASSEMBLY (for RHD)

1. 

   Install the jack assembly.

INSTALL JACK CARRIER CUSHION (for LHD)

1. 

   Install the jack carrier cushion.

INSTALL JACK CARRIER CUSHION (for RHD)

1. 

   Install the jack carrier cushion.

INSTALL REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)

1. 

   Engage the 2 clips and install the rear seat side cover RH.

INSTALL REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)

1. 

   Engage the 3 guides and 3 clips and install the rear No. 1 floor board.

INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY

1. 

   Engage the 2 guides and install the No. 2 deck board sub-assembly.

INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY

1. 

   Engage the 2 guides and install the No. 3 deck board sub-assembly.

INSTALL DECK BOARD ASSEMBLY

1. 

   Install the deck board assembly.

INSTALL REAR DOOR SCUFF PLATE

1. 

   Engage the guide, 3 clips and 5 claws, and install the rear door scuff plate LH.

INSTALL REAR NO. 1 SEAT ASSEMBLY

1. 

   Temporarily install the 2 bolts on the front side of the seat.

2. 

   Temporarily install the 3 bolts on the rear side of the seat.

3. Install the rear No. 1 seat assembly with the 5 bolts.

   37 N*m

   377 kgf*cm

   27 ft.*lbf

CONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY (w/ Remote Folding Function)

1. 

   Remove the rear seat reclining control cable from the carpet hole.

2. Connect the rear seat reclining control cable as shown in the illustration.

3. 

   Connect the rear No. 1 seat lock cable assembly as shown in the illustration.

4. 

   Engage the 2 claws and connect the rear No. 1 seat lock cable assembly as shown in the illustration.

5. Return the seatback to the upright position.

6. 

   Pull up the adjuster's lock piece to lock it as shown in the illustration.

   Note:

   When pressing the lock piece, make sure the adjuster's spring is not compress.

INSPECT REAR SEAT SLIDE ADJUSTER LOCK

1. Check that the left and right adjusters lock simultaneously when sliding the seat.

2. If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.

INSTALL REAR SEAT LEG SIDE COVER

1. 

   Engage the clip.

2. Engage the 3 claws and install the rear seat leg side cover.

INSTALL REAR INNER TRACK BRACKET COVER

1. 

   Engage the 4 claws and install the rear inner track bracket cover.

INSTALL REAR OUTER TRACK BRACKET COVER

1. 

   Engage the 4 claws and install the rear outer track bracket cover.

INSTALL REAR SEAT TRACK BRACKET COVER

1. 

   Engage the 8 claws and install the 2 rear seat track bracket covers.