REAR NO. 1 SEAT OUTER BELT ASSEMBLY INSTALLATION


  1. INSTALL REAR NO. 1 SEAT OUTER BELT ASSEMBLY


    1. A017EAEE01

      Install the rear No. 1 seat outer belt assembly with the 2 bolts.

      Torque:
      Bolt <A>
      7.5 N*m  { 77 kgf*cm, 66 in.*lbf }
      Bolt <B>
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    2. A017BD8

      Connect the shoulder anchor of the rear No. 1 seat outer belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    3. Check if the ELR locks.

      Note

      The check should be performed with outer belt assembly installed.


      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.

  2. INSTALL QUARTER PILLAR GARNISH


    1. A017EVQ

      Engage the 2 guides and the 2 clips, and install the quarter pillar garnish LH as shown in the illustration.

    2. A017DVD

      Engage the 2 guides and the 2 claws, and install the No. 1 seat outer belt guide.

  3. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)


    1. Engage the 4 clips and the 7 claws.

    2. Install the 2 clips.

    3. Install the deck trim side panel assembly LH with the 2 bolts.

      A017FE0

  4. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)


    1. Engage the 4 clips and the 7 claws.

    2. Install the 2 clips.

    3. Install the deck trim side panel assembly RH with the 3 bolts.

      A017FTC

  5. CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY


    1. A017FLFE01

      Connect the floor anchor end of the rear No. 1 seat outer belt assembly and install the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear No. 1 seat outer belt assembly to overlap the protruding part of the floor panel.

  6. INSTALL FRONT DECK SIDE TRIM COVER


    1. A017EJB

      Engage the 4 claws and install the 2 front deck side trim covers LH.

  7. INSTALL NO. 2 DECK SIDE TRIM HOOK (for LH Side)


    1. A017CPF

      Install the No. 2 deck side trim hook with the screw.

  8. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for RH Side)

    Tech Tips

    Use the same procedure for the No. 1 luggage compartment trim hook and the No. 2 deck side trim hook.

  9. INSTALL ROPE HOOK ASSEMBLY


    1. A017D0J

      for Front Side:


      1. Install the rope hook assembly with the bolt.

        Torque:
        6.5 N*m  { 66 kgf*cm, 58 in.*lbf }

      2. Engage the 2 claws.

    2. A017DHF

      for Rear Side:


      1. Install the rope hook assembly with the bolt.

        Torque:
        6.5 N*m  { 66 kgf*cm, 58 in.*lbf }

      2. Engage the 2 claws.

  10. INSTALL REAR DECK TRIM COVER (for LH Side without Remote Folding Function)


    1. A017EYF

      Engage the 10 claws and install the rear deck trim cover.

  11. INSTALL RECLINING REMOTE CONTROL LEVER BEZEL LH (for LH Side with Remote Folding Function)


    1. A017FIS

      Engage the 5 claws and install the reclining remote control bezel LH.

  12. INSTALL REAR POWER OUTLET SOCKET COVER (for LH Side)


    1. A017B0H

      Engage the 2 claws and install the rear power outlet socket cover.

  13. INSTALL REAR POWER POINT SOCKET ASSEMBLY (for LH Side)


    1. A017BVH

      Engage the claw and install the rear power point socket assembly.

    2. Connect the connector.

  14. INSTALL REAR COMBINATION LIGHT SERVICE COVER LH (for LH Side)


    1. A017BGW

      Engage the 2 guides and 6 claws, and install the rear combination light service cover LH.

  15. INSTALL REAR COMBINATION LIGHT SERVICE COVER RH (for RH Side)


    1. A017DDV

      Engage the 2 guides and 6 claws, and install the rear combination light service cover RH.

  16. INSTALL SIDE TRIM COVER RH (for RH Side without Rear Automatic Air Conditioning System)


    1. A017CSI

      Engage the 4 claws, and install the side trim cover RH.

  17. INSTALL REAR ROOM TEMPERATURE SENSOR (for RH Side with Rear Automatic Air Conditioning System)


    1. Connect the connector.

    2. A017B3P

      Engage the 4 claws and install the rear room temperature sensor.

  18. INSTALL SIDE TRIM COVER LH (for LH Side)


    1. A017EO1

      Engage the 10 claws and install the side trim cover LH.

  19. INSTALL DECK SIDE TRIM


    1. A017BAR

      Engage the 3 guides and 4 claws as shown in the illustration.

    2. A017F36

      Install the deck side trim LH with the bolt.

  20. INSTALL DECK SIDE TRIM COVER


    1. A017BA5

      Engage the 2 claws and install the deck side trim cover LH.

  21. INSTALL REAR SEAT SIDE GARNISH CAP (for RH Side without Rear Air Conditioning System)


    1. A017FDU

      Engage the guide and the 8 claws, and install the rear seat side garnish cap.

  22. INSTALL REAR SEAT SIDE GARNISH CAP (for RH Side with Rear Air Conditioning System)


    1. A017ER4

      Engage the guide and the 6 claws.

    2. Install the rear seat side garnish cap with the screw.

  23. INSTALL REAR FLOOR FINISH PLATE


    1. A017BSY

      Engage the 4 clips and the 4 claws, and install the rear floor finish plate.

  24. INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)


    1. A017E5S

      Install the rear No. 2 seat assembly with the 4 bolts.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

  25. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat)


    1. A017F2F

      Install the rear seat lap type belt assembly LH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      After installing the belt, check that it is not twisted.

  26. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat)

  27. INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat)


    1. A017GAE

      Install the rear No. 2 seat inner belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear No. 2 seat inner belt assembly to overlap the protruding part of the rear No. 2 seat bracket.

      Tech Tips

      Use the same procedure for the RH side and LH side.

  28. INSTALL REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)


    1. A017D8N

      Install the rear deck floor box with the 2 nuts.

  29. INSTALL DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)


    1. A017G15

      Install the rear deck floor board assembly with the 4 nuts and 4 bolts.

  30. INSTALL REAR MAT


    1. A017F51

      Install the rear mat.

  31. INSTALL DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)


    1. A017FMA

      Install the 2 nuts and the deck floor board assembly.

    2. Engage the 3 claws.

  32. INSTALL DECK SIDE TRIM BOX LH


    1. Install the deck side trim box LH as shown in the illustration.

      A017CIY
    2. A017BZVE01

      Install the 2 deck side trim clips and the clip.

  33. INSTALL REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)


    1. A017BBU

      Engage the 2 clips and install the rear seat side cover LH.

  34. INSTALL DECK SIDE TRIM BOX RH


    1. Install the deck side trim box RH as shown in the illustration.

      A017EFK
    2. A017FOPE01

      Install the 2 deck side trim clips and the clip.

  35. INSTALL JACK CARRIER ASSEMBLY (for LHD)


    1. A017FWH

      Engage the 3 claws, and install the jack carrier assembly.

  36. INSTALL JACK CARRIER ASSEMBLY (for RHD)


    1. A017G4W

      Engage the 3 claws, and install the jack carrier assembly.

  37. INSTALL JACK ASSEMBLY (for LHD)


    1. A017EKS

      Install the jack assembly.

  38. INSTALL JACK ASSEMBLY (for RHD)


    1. A017DSX

      Install the jack assembly.

  39. INSTALL JACK CARRIER CUSHION (for LHD)


    1. A017ENI

      Install the jack carrier cushion.

  40. INSTALL JACK CARRIER CUSHION (for RHD)


    1. A017D41

      Install the jack carrier cushion.

  41. INSTALL JACK CARRIER SUPPORT

  42. INSTALL REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)


    1. A017EH1

      Engage the 2 clips and install the rear seat side cover RH.

  43. INSTALL REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)


    1. A017CVI

      Engage the 3 guides and 3 clips and install the rear No. 1 floor board.

  44. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

  45. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY


    1. A017D36

      Engage the 2 guides and install the No. 2 deck board sub-assembly.

  46. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY


    1. A017F31

      Engage the 2 guides and install the No. 3 deck board sub-assembly.

  47. INSTALL DECK BOARD ASSEMBLY


    1. A017CPI

      Install the deck board sub-assembly.

  48. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

  49. INSTALL REAR DOOR SCUFF PLATE


    1. A017D4T

      Engage the guide, 3 clips and 5 claws, and install the rear door scuff plate LH.

  50. INSTALL REAR NO. 1 SEAT ASSEMBLY


    1. A017FCR

      Temporarily install the 2 bolts on the front side of the seat.

    2. A017BHD

      Temporarily install the 3 bolts on the rear side of the seat.

    3. Install the rear No. 1 seat assembly with the 5 bolts.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

  51. CONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY (w/ Remote Folding Function)


    1. Remove the rear seat reclining control cable from the carpet hole.

      A017DSHE01

    2. Connect the rear seat reclining control cable as shown in the illustration.

    3. Connect the rear No. 1 seat lock cable assembly as shown in the illustration.

      A017BYUE01
    4. A017EVX

      Engage the 2 claws and connect the rear No. 1 seat lock cable assembly as shown in the illustration.

    5. Return the seatback to the upright position.

    6. Pull up the adjuster's lock piece to lock it as shown in the illustration.

      A017ENNE01

      Note

      When pressing the lock piece, make sure the adjuster's spring is not compress.

  52. INSPECT REAR SEAT SLIDE ADJUSTER LOCK


    1. Check that the left and right adjusters lock simultaneously when sliding the seat.

    2. If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.

  53. INSTALL REAR SEAT LEG SIDE COVER


    1. A017BXU

      Engage the clip.

    2. Engage the 3 claws and install the rear seat leg side cover.

  54. INSTALL REAR INNER TRACK BRACKET COVER


    1. A017FUU

      Engage the 4 claws and install the rear inner track bracket cover.

  55. INSTALL REAR OUTER TRACK BRACKET COVER


    1. A017BNT

      Engage the 4 claws and install the rear outer track bracket cover.

  56. INSTALL REAR SEAT TRACK BRACKET COVER


    1. A017DZY

      Engage the 8 claws and install the 2 rear seat track bracket covers.

  57. INSTALL REAR SEAT HEADREST ASSEMBLY

  58. INSTALL REAR CENTER SEAT ASSEMBLY (for LH Side)