Click here

OCCUPANT DETECTION SENSOR (for Manual Seat) INSTALLATION

Click here
Click here
  1. Click here

    INSTALL SEPARATE TYPE FRONT SEAT CUSHION PAD


    1. A017D42E01

      Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 15 new hog rings.

      Note:

      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

    2. A017EXQE01

      Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 2 new hog rings.

      Note:

      • Be careful not to damage the cover.

      • When installing the hog rings, take care to minimize wrinkles as much as possible.

  2. Click here

    INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD


    1. A017F4K

      Engage each hook.

    2. A017DEI

      Engage the 2 clips and install the front seat cushion cover with pad.

    3. A017BNF

      Engage the 4 hooks.

    4. A017E00

      Connect the occupant detection sensor connector as shown in the illustration.

    5. A017E56

      w/ Front Seat Side Airbag:


      1. Engage the 4 clamps.

  3. Click here

    INSTALL FRONT SEAT INNER BELT ASSEMBLY


    1. A017C2DE01

      Install the front seat inner belt assembly with the nut.

      42 N*m 428 kgf*cm 31 ft.*lbf
      Note:

      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

    2. Connect each connector and clamp.

  4. Click here

    INSTALL FRONT SEAT CUSHION INNER SHIELD

    Tip:

    Use the same procedure for the RH side and the LH side (Click here).

  5. Click here

    INSTALL FRONT SEAT CUSHION SHIELD


    1. A017BGV

      Engage the claw and 2 guides.

    2. A017D08

      Install the front seat cushion shield with the 2 screws.

    3. A017DBS

      Install the 2 hooks on the backside of the front seatback board sub-assembly.

  6. Click here

    INSTALL RECLINING ADJUSTER RELEASE HANDLE

    Tip:

    Use the same procedure for the RH side and the LH side (Click here).

  7. Click here

    INSTALL FRONT SEAT ASSEMBLY

    Tip:

    Use the same procedure for the RH side and the LH side (Click here).

  8. Click here

    INSPECT FRONT SEAT SLIDE ADJUSTER LOCK


    1. During sliding operation of the front seat, check that the left and right adjusters move together smoothly and lock simultaneously.

      If the seat adjusters do not lock simultaneously, loosen the bolts securing the seat to adjust the adjuster position.

  9. Click here

    INSTALL REAR INNER SEAT TRACK COVER

    Tip:

    Use the same procedure for the RH side and the LH side (Click here).

  10. Click here

    INSTALL REAR OUTER SEAT TRACK COVER

    Tip:

    Use the same procedure for the RH side and the LH side (Click here).

  11. Click here

    INSTALL FRONT INNER SEAT TRACK COVER

    Tip:

    Use the same procedure for the RH side and the LH side (Click here).

  12. Click here

    INSTALL FRONT OUTER SEAT TRACK COVER

    Tip:

    Use the same procedure for the RH side and the LH side (Click here).

  13. Click here

    INSTALL FRONT SEAT HEADREST ASSEMBLY

  14. Click here

    CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Front Seat Side Airbag)

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See PageClick here).

  15. Click here

    INSPECT SRS WARNING LIGHT (w/ Front Seat Side Airbag)

    (Click here)