FRONT PASSENGER SEAT BELT WARNING LIGHT REMOVAL


  1. REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY


    1. A017DDAE01

      Apply protective tape to the areas shown in the illustration.

    2. Using a moulding remover, disengage the 2 claws and 5 clips, and then remove the center instrument panel register assembly as shown in the illustration.

  2. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Smart Entry and Start System)


    1. A017BKEE01

      Apply protective tape to the areas shown in the illustration.

    2. Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.

      Note

      Do not pull on the small storage compartment lid. Doing so may cause damage.

    3. Disconnect each connector and remove the center instrument cluster finish panel assembly.

  3. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/ Smart Entry and Start System)


    1. A017EABE01

      Apply protective tape to the areas shown in the illustration.

    2. Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.

      Note

      Do not pull on the small storage compartment lid. Doing so may cause damage.

    3. Disconnect each connector and remove the center instrument cluster finish panel assembly.

  4. REMOVE HEATER CONTROL AND ACCESSORY ASSEMBLY (for Manual Air Conditioning System)


    1. A017G04

      Disengage the 4 clips and remove the heater control and accessory assembly.

    2. Disconnect the connector.

  5. REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)


    1. A017EE0

      Disengage the 4 clips and remove the air conditioning control assembly.

    2. Disconnect the connector.

  6. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Radio Receiver)


    1. A017FXP

      Remove the 4 bolts.

    2. A017EFV

      Pull the radio receiver assembly with bracket toward the rear of the vehicle and disengage the 4 clips.

    3. Disconnect each connector and remove the radio receiver assembly with bracket.

  7. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)


    1. A017EUS

      Remove the 4 bolts.

    2. A017CTX

      Pull the navigation receiver assembly with bracket toward the rear of the vehicle and disengage the 4 clips.

    3. Disconnect each connector and remove the navigation receiver assembly with bracket.

  8. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY WITH BRACKET (w/o Radio Receiver)


    1. A017C93

      Remove the 4 bolts <D>.

    2. Disengage the 4 clips.

    3. Disconnect each connector and remove the integration control and panel assembly with bracket.

  9. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY (w/ Radio Receiver)


    1. A017E42

      Disengage the claw and disconnect the connector.

    2. A017C5M

      Disengage the 2 clips and remove the integration control and panel assembly.

  10. REMOVE NO. 1 RADIO BRACKET (w/ Navigation System)


    1. A017GBL

      Disengage the claw and disconnect the connector.

    2. A017DOO

      Remove the 6 screws and No. 1 radio bracket.

  11. REMOVE NO. 2 RADIO BRACKET (w/ Navigation System)


    1. A017F9I

      Remove the 6 screws and No. 2 radio bracket.

  12. REMOVE NAVIGATION RECEIVER ASSEMBLY (w/ Navigation System)

  13. REMOVE RADIO TUNER OPENING COVER WITH BRACKET (w/o Radio Receiver)


    1. Remove the 2 screws and the radio tuner opening cover with bracket from the integration control and panel assembly.

  14. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY (w/o Radio Receiver)