Click here

SEAT POSITION SENSOR REMOVAL

Click here
Click here
Note:

  • Use the same procedure for the driver side of RHD and LHD vehicles.

  • The procedures listed below are for the driver side of an LHD vehicle.

Click here
  1. Click here

    PRECAUTION

    CAUTION:

    Be sure to read "PRECAUTION" thoroughly before servicing (Click here).

  2. Click here

    DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for Manual Seat)

    CAUTION:

    Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See PageClick here).

  3. Click here

    REMOVE FRONT SEAT HEADREST ASSEMBLY (for Manual Seat)

  4. Click here

    REMOVE FRONT OUTER SEAT TRACK COVER (for Manual Seat)


    1. Lift up the seat track adjusting handle and move the seat to the rearmost position.

    2. A017FOO

      Disengage the 2 claws and remove the front outer seat track cover.

  5. Click here

    REMOVE FRONT INNER SEAT TRACK COVER (for Manual Seat)


    1. A017DLZ

      Disengage the 2 claws and remove the front inner seat track cover.

  6. Click here

    REMOVE REAR SEAT TRACK COVER (for Manual Seat)


    1. Lift up the seat track adjusting handle and move the seat to the foremost position.

    2. A017CWY

      Disengage the 4 claws and remove the 2 rear seat track covers.

  7. Click here

    REMOVE FRONT SEAT ASSEMBLY (for Manual Seat)


    1. A017G32

      Remove the 2 bolts on the rear side of the seat.

    2. Lift up the seat track adjusting handle and move the seat to the rearmost position.

    3. A017D8F

      Remove the 2 bolts on the front side of the seat.

    4. Lift up the seat track adjusting handle and move the seat to the center position. Also, operate the reclining adjuster release handle and move the seatback to the upright position.

    5. Disconnect the connectors under the front seat assembly.

    6. Remove the front seat assembly.

      Note:

      Be careful not to damage the vehicle body.

  8. Click here

    REMOVE FRONT SEAT HEADREST ASSEMBLY (for Power Seat)

  9. Click here

    REMOVE FRONT OUTER SEAT TRACK COVER (for Power Seat)


    1. Operate the power seat switch knob and move the seat to the rearmost position.

    2. A017ET7

      Disengage the 2 claws and remove the front outer seat track cover.

  10. Click here

    REMOVE FRONT INNER SEAT TRACK COVER (for Power Seat)


    1. A017F34

      Disengage the 2 claws and remove the front inner seat track cover.

  11. Click here

    REMOVE REAR OUTER SEAT TRACK COVER (for Power Seat)


    1. Operate the power seat switch knob and move the seat to the foremost position.

    2. A017DLU

      Disengage the 2 claws and remove the rear outer seat track cover.

  12. Click here

    REMOVE REAR INNER SEAT TRACK COVER (for Power Seat)


    1. A017DBE

      Disengage the 2 claws and remove the rear inner seat track cover.

  13. Click here

    REMOVE FRONT SEAT ASSEMBLY (for Power Seat)


    1. A017B0K

      Remove the 2 bolts on the rear side of the seat.

    2. Operate the power seat switch knob and move the seat to the rearmost position.

    3. A017FKL

      Remove the 2 bolts on the front side of the seat.

    4. Operate the power seat switch knob and move the seat to the center position. Also, Operate the power seat switch knob and move the seatback to the upright position.

    5. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent the airbag and seat belt pretensioner from deploying (Click here).

      • If the side airbag was deployed, replace the front seat assembly with a new one.

      Note:

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

    6. Disconnect each connector under the front seat assembly.

    7. Remove the front seat assembly.

      Note:

      Be careful not to damage the vehicle body.

  14. Click here

    REMOVE SEAT POSITION SENSOR


    1. A017BHS

      Disconnect the connector.

    2. Using a "TORX" socket wrench (T30), remove the "TORX" screw and seat position sensor with the seat slide position sensor protector.

    3. A017BB3

      Remove the seat position sensor from the seat slide position sensor protector as shown in the illustration.