REAR AIRBAG SENSOR INSTALLATION


  1. INSTALL REAR AIRBAG SENSOR


    1. Check that the ignition switch is off.

    2. Check that the battery negative (-) cable is disconnected.

      CAUTION:

      Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.

    3. A017D1V

      Install the rear airbag sensor with the bolt and pin.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

      Note


      • If the rear airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.

      • When installing the rear airbag sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

      • Make sure that the pin is securely inserted into the body hole.

      • Tighten the bolt while holding the rear airbag sensor because the rear airbag sensor pin (stopper) is easily damaged.

    4. Check that there are no loose parts after installing the rear airbag sensor.

    5. Connect the connector to the rear airbag sensor.

      Note

      When handling the airbag connector, take care not to damage the airbag wire harness.

  2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Engage the 4 clips and 7 claws.

    2. Install the 2 clips.

    3. Install the deck trim side panel assembly LH with the 2 bolts.

      A017FE0

  3. INSTALL REAR NO. 1 SEAT OUTER BELT ASSEMBLY


    1. A017FLFE01

      Connect the floor anchor end of the rear No. 1 seat outer belt assembly and install the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear No. 1 seat outer belt assembly to overlap the protruding part of the floor panel.

  4. INSTALL FRONT DECK SIDE TRIM COVER


    1. A017EJB

      Engage the 4 claws and install the 2 front deck side trim covers LH.

  5. INSTALL NO. 2 DECK SIDE TRIM HOOK


    1. A017CPF

      Install the No. 2 deck side trim hook with the screw.

  6. INSTALL ROPE HOOK ASSEMBLY


    1. A017D0J

      for Front Side:


      1. Install the rope hook assembly with the bolt.

        Torque:
        6.5 N*m  { 66 kgf*cm, 58 in.*lbf }

      2. Engage the 2 claws.

    2. A017DHF

      for Rear Side:


      1. Install the rope hook assembly with the bolt.

        Torque:
        6.5 N*m  { 66 kgf*cm, 58 in.*lbf }

      2. Engage the 2 claws.

  7. INSTALL RECLINING REMOTE CONTROL LEVER BEZEL LH (w/ Remote Folding Function)


    1. A017FIS

      Engage the 5 claws to install the reclining remote control lever bezel LH.

  8. INSTALL REAR DECK TRIM COVER (w/o Remote Folding Function)


    1. A017EYF

      Engage the 10 claws to install the rear deck trim cover.

  9. INSTALL REAR POWER OUTLET SOCKET COVER


    1. A017B0H

      Engage the 2 claws and install the rear power outlet socket cover.

  10. INSTALL REAR POWER POINT SOCKET ASSEMBLY


    1. A017BVH

      Engage the claw and install the rear power point socket assembly.

    2. Connect the connector.

  11. INSTALL REAR COMBINATION LIGHT SERVICE COVER LH


    1. A017BGW

      Engage the 2 guides and 6 claws, and install the rear combination light service cover LH.

  12. INSTALL SIDE TRIM COVER LH


    1. A017EO1

      Engage the 10 claws and install the side trim cover LH.

  13. INSTALL DECK SIDE TRIM


    1. A017BAR

      Engage the 3 guides and 4 claws as shown in the illustration.

    2. A017F36

      Install the deck side trim LH with the bolt.

  14. INSTALL DECK SIDE TRIM COVER


    1. A017BA5

      Engage the 2 claws and install the deck side trim cover LH.

  15. INSTALL REAR FLOOR FINISH PLATE


    1. A017BSY

      Engage the 4 clips and 4 claws, and install the rear floor finish plate.

  16. INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)


    1. Install the 6 bolts on the rear of the seat.

      A017CU1
      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

    2. Install the rear No. 2 seat assembly with the bolt.

      A017E17
      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

  17. INSTALL CENTER SEAT CUSHION COVER SUB-ASSEMBLY (w/ Rear No. 2 Seat)

  18. INSTALL REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH (w/ Rear No. 2 Seat)


    1. A017DK9E01
      Text in Illustration
      *1 Rubber Band

      Route the rear No. 2 seat outer belt assembly LH through the rubber band as shown in the illustration.

    2. Install the rear No. 2 seat outer belt assembly LH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      After installing the belt, check that it is not twisted.

  19. INSTALL REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH (w/ Rear No. 2 Seat)

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  20. INSTALL REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)


    1. A017D8N

      Install the rear deck floor box with the 2 nuts.

  21. INSTALL DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)


    1. A017G15

      Install the 2 nuts and deck floor board assembly.

    2. Engage the 3 claws.

  22. INSTALL REAR MAT


    1. A017F51

      Install the rear mat.

  23. INSTALL DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)


    1. A017FYN

      Install the rear deck floor board assembly with the 4 nuts and 4 bolts.

  24. INSTALL DECK SIDE TRIM BOX LH


    1. Install the deck side trim box LH as shown in the illustration.

      A017CIY
    2. A017BZVE01

      Install the 2 deck side trim clips and clip.

  25. INSTALL REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)


    1. A017BBU

      Engage the 2 clips and install the rear seat side cover LH.

  26. INSTALL DECK SIDE TRIM BOX RH


    1. Install the deck side trim box RH as shown in the illustration.

      A017EFK
    2. A017FOPE01

      Install the 2 deck side trim clips and clip.

  27. INSTALL JACK CARRIER ASSEMBLY (for LHD)


    1. A017FWH

      Engage the 3 claws, and install the jack carrier assembly.

  28. INSTALL JACK CARRIER ASSEMBLY (for RHD)


    1. A017G4W

      Engage the 3 claws, and install the jack carrier assembly.

  29. INSTALL JACK ASSEMBLY (for LHD)


    1. A017EKS

      Install the jack assembly.

  30. INSTALL JACK ASSEMBLY (for RHD)


    1. A017DSX

      Install the jack assembly.

  31. INSTALL JACK CARRIER CUSHION (for LHD)


    1. A017ENI

      Install the jack carrier cushion.

  32. INSTALL JACK CARRIER CUSHION (for RHD)


    1. A017D41

      Install the jack carrier cushion.

  33. INSTALL JACK CARRIER SUPPORT

  34. INSTALL REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)


    1. A017EH1

      Engage the 2 clips and install the rear seat side cover RH.

  35. INSTALL REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)


    1. A017CVI

      Engage the 3 guides and 3 clips and install the rear No. 1 floor board.

  36. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Install the tonneau cover assembly.

  37. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY


    1. A017D36

      Engage the 2 guides and install the No. 2 deck board sub-assembly.

  38. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY


    1. A017F31

      Engage the 2 guides and install the No. 3 deck board sub-assembly.

  39. INSTALL DECK BOARD ASSEMBLY


    1. A017CPI

      Install the deck board assembly.

  40. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP


    1. A017F49E01

      Align the alignment mark (red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  41. INSTALL REAR DOOR SCUFF PLATE


    1. A017D4T

      Engage the guide, 3 clips and 5 claws, and install the rear door scuff plate LH.

  42. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  43. INSPECT SRS WARNING LIGHT


    1. Inspect the SRS warning light Click here.