Click here

REAR AIRBAG SENSOR INSTALLATION

Click here
Click here
  1. Click here

    INSTALL REAR AIRBAG SENSOR


    1. Check that the ignition switch is off.

    2. Check that the battery negative (-) cable is disconnected.

      CAUTION:

      Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.

    3. A017D1V

      Install the rear airbag sensor with the bolt and pin.

      9.0 N*m 92 kgf*cm 80 in.*lbf
      Note:

      • If the rear airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.

      • When installing the rear airbag sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

      • Make sure that the pin is securely inserted into the body hole.

      • Tighten the bolt while holding the rear airbag sensor because the rear airbag sensor pin (stopper) is easily damaged.

    4. Check that there are no loose parts after installing the rear airbag sensor.

    5. Connect the connector to the rear airbag sensor.

      Note:

      When handling the airbag connector, take care not to damage the airbag wire harness.

  2. Click here

    INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)


    1. Engage the 4 clips and the 7 claws.

    2. Install the 2 clips.

    3. A017FE0

      Install the deck trim side panel assembly LH with the 2 bolts.

  3. Click here

    INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)


    1. Engage the 4 clips and the 7 claws.

    2. Install the 2 clips.

    3. A017FTC

      Install the deck trim side panel assembly RH with the 3 bolts.

  4. Click here

    INSTALL REAR NO. 1 SEAT OUTER BELT ASSEMBLY


    1. A017FLFE01

      Connect the floor anchor end of the rear No. 1 seat outer belt assembly and install the bolt.

      42 N*m 428 kgf*cm 31 ft.*lbf
      Note:

      Do not allow the anchor part of the rear No. 1 seat outer belt assembly to overlap the protruding part of the floor panel.

  5. Click here

    INSTALL FRONT DECK SIDE TRIM COVER


    1. A017EJB

      Engage the 4 claws and install the 2 front deck side trim covers LH.

  6. Click here

    INSTALL NO. 2 DECK SIDE TRIM HOOK (for LH Side)


    1. A017CPF

      Install the No. 2 deck side trim hook with the screw.

  7. Click here

    INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for RH Side)

    Tip:

    Use the same procedure for the No. 1 luggage compartment trim hook and the No. 2 deck side trim hook (Click here).

  8. Click here

    INSTALL ROPE HOOK ASSEMBLY


    1. A017D0J

      for Front Side:


      1. Install the rope hook assembly with the bolt.

        6.5 N*m 66 kgf*cm 58 in.*lbf

      2. Engage the 2 claws.

    2. A017DHF

      for Rear Side:


      1. Install the rope hook assembly with the bolt.

        6.5 N*m 66 kgf*cm 58 in.*lbf

      2. Engage the 2 claws.

  9. Click here

    INSTALL RECLINING REMOTE CONTROL LEVER BEZEL LH (for LH Side with Remote Folding Function)


    1. A017FIS

      Engage the 5 claws and install the reclining remote control bezel LH.

  10. Click here

    INSTALL REAR DECK TRIM COVER (for LH Side without Remote Folding Function)


    1. A017EYF

      Engage the 10 claws and install the rear deck trim cover.

  11. Click here

    INSTALL REAR POWER OUTLET SOCKET COVER (for LH Side)


    1. A017B0H

      Engage the 2 claws and install the rear power outlet socket cover.

  12. Click here

    INSTALL REAR POWER POINT SOCKET ASSEMBLY (for LH Side)


    1. A017BVH

      Engage the claw and install the rear power point socket assembly.

    2. Connect the connector.

  13. Click here

    INSTALL REAR COMBINATION LIGHT SERVICE COVER LH (for LH Side)


    1. A017BGW

      Engage the 2 guides and 6 claws, and install the rear combination light service cover LH.

  14. Click here

    INSTALL REAR COMBINATION LIGHT SERVICE COVER RH (for RH Side)


    1. A017DDV

      Engage the 2 guides and 6 claws, and install the rear combination light service cover RH.

  15. Click here

    INSTALL SIDE TRIM COVER RH (for RH Side without Rear Automatic Air Conditioning System)


    1. A017CSI

      Engage the 4 claws, and install the side trim cover RH.

  16. Click here

    INSTALL REAR ROOM TEMPERATURE SENSOR (for RH Side with Rear Automatic Air Conditioning System)


    1. Connect the connector.

    2. A017B3P

      Engage the 4 claws and install the rear room temperature sensor.

  17. Click here

    INSTALL SIDE TRIM COVER LH (for LH Side)


    1. A017EO1

      Engage the 10 claws and install the side trim cover LH.

  18. Click here

    INSTALL DECK SIDE TRIM


    1. A017BAR

      Engage the 3 guides and 4 claws as shown in the illustration.

    2. A017F36

      Install the deck side trim LH with the bolt.

  19. Click here

    INSTALL DECK SIDE TRIM COVER


    1. A017BA5

      Engage the 2 claws and install the deck side trim cover LH.

  20. Click here

    INSTALL REAR SEAT SIDE GARNISH CAP (for RH Side without Rear Air Conditioning System)


    1. A017FDU

      Engage the guide and the 8 claws, and install the rear seat side garnish cap.

  21. Click here

    INSTALL REAR SEAT SIDE GARNISH CAP (for RH Side with Rear Air Conditioning System)


    1. A017ER4

      Engage the guide and the 6 claws.

    2. Install the rear seat side garnish cap with the screw.

  22. Click here

    INSTALL REAR FLOOR FINISH PLATE


    1. A017BSY

      Engage the 4 clips and the 4 claws, and install the rear floor finish plate.

  23. Click here

    INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)


    1. A017E5S

      Install the rear No. 2 seat assembly with the 4 bolts.

      37 N*m 377 kgf*cm 27 ft.*lbf
  24. Click here

    INSTALL REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat)


    1. A017F2F

      Install the rear seat lap type belt assembly LH with the bolt.

      42 N*m 428 kgf*cm 31 ft.*lbf
      Note:

      After installing the belt, check that it is not twisted.

  25. Click here

    INSTALL REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat)

    Tip:

    Use the same procedure for the RH side and the LH side (Click here).

  26. Click here

    INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat)


    1. A017GAE

      Install the rear No. 2 seat inner belt assembly with the bolt.

      42 N*m 428 kgf*cm 31 ft.*lbf
      Note:

      Do not allow the anchor part of the rear No. 2 seat inner belt assembly to overlap the protruding part of the rear No. 2 seat bracket.

      Tip:

      Use the same procedure for the RH side and LH side.

  27. Click here

    INSTALL NO. 1 DECK BOARD (w/o Rear No. 2 Seat)


    1. A017DA0

      Engage the 3 clips and install the rear floor board spacer to the No. 1 deck board.

  28. Click here

    INSTALL NO. 1 DECK BOARD (w/ Rear No. 2 Seat)


    1. A017DDB

      Engage the 5 clips and install the deck floor box to the No. 1 deck board.

  29. Click here

    INSTALL REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)


    1. A017D8N

      Install the rear deck floor box with the 2 nuts.

  30. Click here

    INSTALL DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)


    1. A017FMA

      Install the 2 nuts and the deck floor board assembly.

    2. Engage the 3 claws.

  31. Click here

    INSTALL REAR MAT


    1. A017F51

      Install the rear mat.

  32. Click here

    INSTALL DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)


    1. A017G15

      Install the rear deck floor board assembly with the 4 nuts and 4 bolts.

  33. Click here

    INSTALL DECK SIDE TRIM BOX LH


    1. A017CIY

      Install the deck side trim box LH as shown in the illustration.

    2. A017BZVE01

      Install the 2 deck side trim clips and the clip.

  34. Click here

    INSTALL REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)


    1. A017BBU

      Engage the 2 clips and install the rear seat side cover LH.

  35. Click here

    INSTALL DECK SIDE TRIM BOX RH


    1. A017EFK

      Install the deck side trim box RH as shown in the illustration.

    2. A017FOPE01

      Install the 2 deck side trim clips and the clip.

  36. Click here

    INSTALL JACK CARRIER ASSEMBLY (for LHD)


    1. A017FWH

      Engage the 3 claws, and install the jack carrier assembly.

  37. Click here

    INSTALL JACK CARRIER ASSEMBLY (for RHD)


    1. A017G4W

      Engage the 3 claws, and install the jack carrier assembly.

  38. Click here

    INSTALL JACK ASSEMBLY (for LHD)


    1. A017EKS

      Install the jack assembly.

  39. Click here

    INSTALL JACK ASSEMBLY (for RHD)


    1. A017DSX

      Install the jack assembly.

  40. Click here

    INSTALL JACK CARRIER CUSHION (for LHD)


    1. A017ENI

      Install the jack carrier cushion.

  41. Click here

    INSTALL JACK CARRIER CUSHION (for RHD)


    1. A017D41

      Install the jack carrier cushion.

  42. Click here

    INSTALL JACK CARRIER SUPPORT

  43. Click here

    INSTALL REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)


    1. A017EH1

      Engage the 2 clips and install the rear seat side cover RH.

  44. Click here

    INSTALL REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)


    1. A017CVI

      Engage the 3 guides and 3 clips and install the rear No. 1 floor board.

  45. Click here

    INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Install the tonneau cover assembly.

  46. Click here

    INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY


    1. A017D36

      Engage the 2 guides and install the No. 2 deck board sub-assembly.

  47. Click here

    INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY


    1. A017F31

      Engage the 2 guides and install the No. 3 deck board sub-assembly.

  48. Click here

    INSTALL DECK BOARD ASSEMBLY


    1. A017CPI

      Install the deck board sub-assembly.

  49. Click here

    INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP


    1. A017F49E01

      Align the alignment mark (red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

      Note:

      After installation, check that the corners fit correctly.

  50. Click here

    INSTALL REAR DOOR SCUFF PLATE


    1. A017D4T

      Engage the guide, 3 clips and 5 claws, and install the rear door scuff plate LH.

  51. Click here

    CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See PageClick here).

  52. Click here

    INSPECT SRS WARNING LIGHT


    1. Inspect the SRS warning light (Click here).