CENTER AIRBAG SENSOR ASSEMBLY INSTALLATION


  1. INSTALL CENTER AIRBAG SENSOR ASSEMBLY


    1. Check that the ignition switch is off.

    2. Check that the battery negative (-) cable is disconnected.

      CAUTION:

      Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.

    3. A017CSRE01

      Install the center airbag sensor assembly with the 3 bolts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

      Note


      • If the center airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.

      • When installing the center airbag sensor assembly, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

      • When the ignition switch is first turned on (IG) after the center airbag sensor assembly has been replaced, make sure that no one is in the vehicle.

    4. Check that there are no loose parts after installing the center airbag sensor assembly.

    5. Connect the holder (with connectors).

      Note

      When handling the airbag connector, take care not to damage the airbag wire harness.

    6. Check that the waterproof sheet is properly set.

  2. INSTALL FRONT NO. 2 CONSOLE BOX INSERT (for LHD)


    1. A017BSW

      Engage the claw and 2 guides.

    2. Install the front No. 2 console box insert with the 3 screws <F> and clip.

  3. INSTALL FRONT NO. 2 CONSOLE BOX INSERT (for RHD)


    1. A017BQH

      Engage the claw and 2 guides.

    2. Install the front No. 2 console box insert with the 3 screws <F> and clip.

  4. INSTALL FRONT NO. 1 CONSOLE BOX INSERT (for LHD)


    1. A017FLQ

      Engage the claw and 2 guides.

    2. Install the front No. 1 console box insert with the 3 screws <F> and 2 clips.

  5. INSTALL FRONT NO. 1 CONSOLE BOX INSERT (for RHD)


    1. A017BG4

      Engage the claw and 2 guides.

    2. Install the front No. 1 console box insert with the 3 screws <F> and clip.

  6. INSTALL CONSOLE BOX ASSEMBLY (w/o Rear Air Conditioning System)


    1. A017G3R

      Engage the 6 claws.

    2. A017E57

      Install the console box assembly with the 4 bolts and 2 screws.

  7. INSTALL CONSOLE BOX ASSEMBLY (w/ Rear Air Conditioning System)


    1. A017E8O

      Engage the 6 claws.

    2. Connect the connector.

    3. A017C3F

      Install the console box assembly with the 4 bolts and 2 screws.

  8. INSTALL LOWER REAR CONSOLE BOX


    1. Install the lower rear console box.

  9. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. A017FDP

      Connect the connector.

    2. Engage the 4 claws and 4 clips, and install the upper console panel sub-assembly.

  10. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Smart Entry and Start System)


    1. A017EYQE01

      Apply protective tape to the areas shown in the illustration.

    2. Connect each connector.

    3. Engage the 10 claws and 8 clips, and install the center instrument cluster finish panel assembly.

      Note

      Do not the damage the instrument panel safety pad assembly and lower instrument panel finish panel sub-assembly.

  11. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/ Smart Entry and Start System)


    1. A017D5UE01

      Apply protective tape to the areas shown in the illustration.

    2. Connect each connector.

    3. Engage the 10 claws and 8 clips, and install the center instrument cluster finish panel assembly.

      Note

      Do not the damage the instrument panel safety pad assembly and lower instrument panel finish panel sub-assembly.

  12. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    1. Connect each connector and clamp.

    2. A017F5K

      Engage the 4 claws and 3 clips.

    3. Install the lower instrument panel sub-assembly with the 2 bolts <B> and 3 screws <F>.

  13. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. A017F65

      Engage the 2 guides.

    2. Engage the 3 claws and install the No. 2 instrument panel under cover sub-assembly.

  14. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)


    1. A017BY3

      Connect the hood lock control cable assembly.

    2. Connect each connector.

    3. Engage the 3 claws and 10 clips.

    4. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.

  15. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Automatic Air Conditioning System)


    1. A017CWD

      Connect the hood lock control cable assembly.

    2. Connect each connector and the aspirator duct.

    3. A017EU2

      Engage the 3 claws and 10 clips.

    4. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.

  16. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A017G63

      Engage the claw and clip, install the cowl side trim sub-assembly LH.

    2. Install the clip.

  17. INSTALL FRONT DOOR SCUFF PLATE LH


    1. A017B6P

      Engage the guide and the 8 claws, and install the front door scuff plate LH.

  18. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  19. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  21. INSPECT SRS WARNING LIGHT


    1. Inspect the SRS warning light Click here.