CURTAIN SHIELD AIRBAG ASSEMBLY INSTALLATION


  1. INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY


    1. Check that the ignition switch is off.

    2. Check that the battery negative (-) cable is disconnected.

      CAUTION:

      Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.

    3. Temporarily install the curtain shield airbag assembly to the body panel with the 11 hooks.

      Note

      Do not twist the curtain shield airbag assembly when installing it.

    4. Install 11 new bolts.

      Torque:
      9.8 N*m  { 100 kgf*cm, 87 in.*lbf }

      Tech Tips

      Tighten the bolts in the order shown in the illustration.

      A017CURE01

    5. Connect the curtain shield airbag connector.

      Note

      When handling the airbag connector, take care not to damage the airbag wire harness.

      A017C0O

  2. INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)


    1. A017B15

      Pull the roof headlining assembly into the vehicle through the back door.

      Note

      Do not damage the roof headlining assembly or body interior.

    2. Install the 4 clips.

    3. Connect the No. 2 antenna cord sub-assembly connector to the rear pillar RH.

    4. Connect the No. 2 antenna cord sub-assembly connectors and engage the 3 clamps to the front pillar RH.

    5. Install the No. 2 antenna cord sub-assembly to the front pillar RH with the bolt.

    6. Connect the No. 1 roof wire connector and engage the 3 clamps to the front pillar LH.

      A017ER8E01

      Note

      After installation, make sure that the back door weatherstrip does not interfere with the roof headlining assembly.

  3. INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)


    1. A017EKD

      Pull the roof headlining assembly into the vehicle through the back door.

      Note

      Do not damage the roof headlining assembly or body interior.

    2. Install the 3 clips.

    3. Connect the sliding roof drive gear connector.

    4. Connect the No. 2 antenna cord sub-assembly connector to the rear pillar RH.

    5. Connect the No. 2 antenna cord sub-assembly connector and engage the 3 clamps to the front pillar RH.

    6. Install the No. 2 antenna cord sub-assembly to the front pillar RH with the bolt.

    7. w/ Rear Seat Entertainment System:


      1. Connect the No. 1 roof wire connector to the rear pillar LH.

    8. Connect the No. 1 roof wire connectors and engage the 3 clamps to the front pillar LH.

      A017FCLE01

      Note

      After installation, make sure that the back door weatherstrip does not interfere with the roof headlining assembly.

  4. INSTALL VISOR HOLDER


    1. A017E30

      Engage the 2 claws.

    2. Push in the visor holder as shown in the illustration.

      Tech Tips

      Use the same procedure for the RH side and the LH side.

  5. INSTALL SUN ROOF OPENING TRIM MOULDING (w/ Sliding Roof)


    1. A017EO4E01

      Align the joining point of the moulding with the notch of the roof headlining assembly, and install the sun roof opening trim moulding.

      Note

      After installation, check that the corners fit correctly.

  6. INSTALL ROOF HEADLINING TRIM CLIP STOPPER


    1. A017DXQ

      Install the roof headlining trim clip stopper with the bolt.

    2. Engage the 3 claws.

      Tech Tips

      Use the same procedure for the RH side and the LH side.

  7. INSTALL ASSIST GRIP ASSEMBLY (w/ Sliding Roof)


    1. A017G2T

      Assemble the assist grip assembly as shown in the illustration.

    2. A017FSD

      Install the assist grip assembly.

      Tech Tips

      Use the same procedure for the other 4 assist grips.

  8. INSTALL REAR ASSIST GRIP SUB-ASSEMBLY (w/o Sliding Roof)


    1. A017C8H

      Assemble the rear assist grip sub-assembly as shown in the illustration.

    2. A017DWB

      Install the rear assist grip sub-assembly.

      Tech Tips

      Use the same procedure for the other 4 assist grips.

  9. INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY (w/o Sliding Roof)


    1. A017CK0

      Assemble the front assist grip sub-assembly as shown in the illustration.

    2. A017BDN

      Install the front assist grip sub-assembly.

      Tech Tips

      Use the same procedure for the other 3 assist grips.

  10. INSTALL TELEVISION DISPLAY ASSEMBLY (w/ Rear Seat Entertainment System)


    1. A017CFP

      Engage the 2 claws and the 2 clips.

    2. A017E98

      Install the television display with the 4 bolts.

      Tech Tips

      Tighten the bolts in the order shown in the illustration.

    3. Connect the connector.

  11. INSTALL TELEVISION BASE (w/ Rear Seat Entertainment System)


    1. A017BXWE01

      Engage the 2 guides and 4 clips and install the television base.

  12. INSTALL NO. 2 ROOM LIGHT ASSEMBLY


    1. A017DBN

      Engage the 4 claws and install the lens cover.

    2. A017EET

      Engage the 4 claws and install the room light switch base to the No. 2 room light assembly.

    3. A017G8V

      Engage the 4 claws and install the No. 2 room light assembly.

  13. INSTALL NO. 1 ROOM LIGHT ASSEMBLY (for Standard)


    1. A017DBN

      Engage the 4 claws and install the lens cover.

    2. A017EET

      Engage the 4 claws and install the room light switch base to the No. 1 room light assembly.

    3. A017G8V

      Engage the 4 claws and install the No. 1 room light assembly.

  14. INSTALL NO. 1 ROOM LIGHT ASSEMBLY (for Independent Type)


    1. A017ERL

      Engage the 4 claws and install the lens cover.

    2. A017C7P

      Engage the 8 claws and install the room light switch base to the No. 1 room light assembly.

    3. A017F7A

      Engage the 4 claws and install the No. 1 room light assembly.

  15. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


    1. A017E8X

      Engage the 2 claws and install the inner rear view mirror stay holder cover.

    2. A017CUUE01

      Engage the 2 claws and install the inner rear view mirror stay holder cover as shown in the illustration.

  16. INSTALL VISOR ASSEMBLY LH


    1. A017BSF

      Install the visor assembly LH with the 2 screws.

  17. INSTALL VISOR BRACKET COVER (for LH Side)


    1. A017G99

      Engage the 4 claws and install the visor bracket cover.

  18. INSTALL VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  19. INSTALL VISOR BRACKET COVER (for RH Side)

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  20. INSTALL ROOF CONSOLE BOX ASSEMBLY


    1. A017F3L

      Connect the connector.

    2. Engage the 3 guides, 2 clips, fastener, and install the roof console box assembly.

  21. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH (w/o Power Back Door)


    1. w/ Rear No. 2 Seat:


      1. A017FTJ

        Engage the 2 guides and 5 clips.

      2. Install the roof side inner garnish assembly LH with the bolt.

      3. A017DAD

        Engage the 2 guides and the 2 claws, and install the No. 2 seat outer belt guide.

    2. w/o Rear No. 2 Seat:


      1. A017ES0

        Engage the 2 guides and 5 clips.

      2. Install the roof side inner garnish assembly LH with the bolt.

  22. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH (w/ Power Back Door)


    1. w/ Rear No. 2 Seat:


      1. A017EMC

        Engage the 2 guides and 5 clips.

      2. Install the roof side inner garnish assembly LH with the bolt.

      3. A017DAD

        Engage the 2 guides and the 2 claws, and install the No. 2 seat outer belt guide.

    2. w/o Rear No. 2 Seat:


      1. A017E6D

        Engage the 2 guides and 5 clips.

      2. Install the roof side inner garnish assembly LH with the bolt.

  23. INSTALL QUARTER PILLAR GARNISH LH


    1. A017EVQ

      Engage the 2 guides and the 2 clips, and install the quarter pillar garnish LH as shown in the illustration.

    2. A017DVD

      Engage the 2 guides and the 2 claws, and install the No. 1 seat outer belt guide.

  24. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Engage the 4 clips and the 7 claws.

    2. Install the 2 clips.

    3. Install the deck trim side panel assembly LH with the 2 bolts.

      A017FE0

  25. CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH


    1. A017FLFE01

      Connect the floor anchor end of the rear No. 1 seat outer belt assembly and install the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear No. 1 seat outer belt assembly to overlap the protruding part of the floor panel.

  26. INSTALL FRONT DECK SIDE TRIM COVER LH


    1. A017EJB

      Engage the 4 claws and install the 2 front deck side trim covers LH.

  27. INSTALL NO. 2 DECK SIDE TRIM HOOK


    1. A017CPF

      Install the No. 2 deck side trim hook with the screw.

  28. INSTALL ROPE HOOK ASSEMBLY (for LH Side)


    1. A017D0J

      for Front Side:


      1. Install the rope hook assembly with the bolt.

        Torque:
        6.5 N*m  { 66 kgf*cm, 58 in.*lbf }

      2. Engage the 2 claws.

    2. A017DHF

      for Rear Side:


      1. Install the rope hook assembly with the bolt.

        Torque:
        6.5 N*m  { 66 kgf*cm, 58 in.*lbf }

      2. Engage the 2 claws.

  29. INSTALL REAR DECK TRIM COVER (w/o Remote Folding Function)


    1. A017EYF

      Engage the 10 claws and install the rear deck trim cover.

  30. INSTALL RECLINING REMOTE CONTROL LEVER BEZEL LH (w/ Remote Folding Function)


    1. A017FIS

      Engage the 5 claws and install the reclining remote control bezel LH.

  31. INSTALL REAR POWER OUTLET SOCKET COVER


    1. A017B0H

      Engage the 2 claws and install the rear power outlet socket cover.

  32. INSTALL REAR POWER POINT SOCKET ASSEMBLY


    1. A017BVH

      Engage the claw and install the rear power point socket assembly.

    2. Connect the connector.

  33. INSTALL REAR COMBINATION LIGHT SERVICE COVER LH


    1. A017BGW

      Engage the 2 guides and 6 claws, and install the rear combination light service cover LH.

  34. INSTALL SIDE TRIM COVER LH


    1. A017EO1

      Engage the 10 claws and install the side trim cover LH.

  35. INSTALL DECK SIDE TRIM LH


    1. A017BAR

      Engage the 3 guides and 4 claws as shown in the illustration.

    2. A017F36

      Install the deck side trim LH with the bolt.

  36. INSTALL DECK SIDE TRIM COVER NO.2


    1. A017BA5

      Engage the 2 claws and install the deck side trim cover LH.

  37. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH (w/o Rear No. 2 Seat)

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  38. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH (w/ Rear No. 2 Seat)

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  39. INSTALL QUARTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  40. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH


    1. Engage the 4 clips and the 7 claws.

    2. Install the 2 clips.

    3. Install the deck trim side panel assembly RH with the 3 bolts.

      A017FTC

  41. CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  42. INSTALL FRONT DECK SIDE TRIM COVER RH

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  43. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

    Tech Tips

    Use the same procedure for the No. 1 luggage compartment trim hook and the No. 2 deck side trim hook Click here.

  44. INSTALL ROPE HOOK ASSEMBLY (for RH Side)

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  45. INSTALL REAR COMBINATION LIGHT SERVICE COVER RH


    1. A017DDV

      Engage the 2 guides and 6 claws, and install the rear combination light service cover RH.

  46. INSTALL REAR ROOM TEMPERATURE SENSOR (w/ Rear Automatic Air Conditioning System)


    1. Connect the connector.

    2. A017B3P

      Engage the 4 claws and install the rear room temperature sensor.

  47. INSTALL SIDE TRIM COVER RH (w/o Rear Automatic Air Conditioning System)


    1. A017CSI

      Engage the 4 claws, and install the side trim cover RH.

  48. INSTALL DECK SIDE TRIM RH

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  49. INSTALL DECK SIDE TRIM COVER NO.1

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  50. INSTALL REAR SEAT SIDE GARNISH CAP (w/o Rear Air Conditioning System)


    1. A017FDU

      Engage the guide and the 8 claws, and install the rear seat side garnish cap.

  51. INSTALL REAR SEAT SIDE GARNISH CAP (w/ Rear Air Conditioning System)


    1. A017ER4

      Engage the guide and the 6 claws.

    2. Install the rear seat side garnish cap with the screw.

  52. INSTALL REAR FLOOR FINISH PLATE


    1. A017BSY

      Engage the 4 clips and the 4 claws, and install the rear floor finish plate.

  53. INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)


    1. A017E5S

      Install the rear No. 2 seat assembly with the 4 bolts.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

  54. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat)


    1. A017F2F

      Install the rear seat lap type belt assembly LH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      After installing the belt, check that it is not twisted.

  55. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat)


    1. Install the rear seat lap type belt assembly RH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      After installing the belt, check that it is not twisted.

  56. INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat)


    1. A017GAE

      Install the rear No. 2 seat inner belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear No. 2 seat inner belt assembly to overlap the protruding part of the rear No. 2 seat bracket.

      Tech Tips

      Use the same procedure for the RH side and LH side.

  57. INSTALL NO. 1 DECK BOARD (w/o Rear No. 2 Seat)


    1. A017DA0

      Engage the 3 clips and install the rear floor board spacer to the No. 1 deck board.

  58. INSTALL NO. 1 DECK BOARD (w/ Rear No. 2 Seat)


    1. A017DDB

      Engage the 5 clips and install the deck floor box to the No. 1 deck board.

  59. INSTALL REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)


    1. A017D8N

      Install the rear deck floor box with the 2 nuts.

  60. INSTALL DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)


    1. A017FMA

      Install the 2 nuts and the deck floor board assembly.

    2. Engage the 3 claws.

  61. INSTALL REAR MAT


    1. A017F51

      Install the rear mat.

  62. INSTALL DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)


    1. A017G15

      Install the rear deck floor board assembly with the 4 nuts and 4 bolts.

  63. INSTALL DECK SIDE TRIM BOX LH


    1. Install the deck side trim box LH as shown in the illustration.

      A017CIY
    2. A017BZVE01

      Install the 2 deck side trim clips and the clip.

  64. INSTALL REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)


    1. A017BBU

      Engage the 2 clips and install the rear seat side cover LH.

  65. INSTALL DECK SIDE TRIM BOX RH


    1. Install the deck side trim box RH as shown in the illustration.

      A017EFK
    2. A017FOPE01

      Install the 2 deck side trim clips and the clip.

  66. INSTALL JACK CARRIER ASSEMBLY (for LHD)


    1. A017FWH

      Engage the 3 claws, and install the jack carrier assembly.

  67. INSTALL JACK CARRIER ASSEMBLY (for RHD)


    1. A017G4W

      Engage the 3 claws, and install the jack carrier assembly.

  68. INSTALL JACK ASSEMBLY (for LHD)


    1. A017EKS

      Install the jack assembly.

  69. INSTALL JACK ASSEMBLY (for RHD)


    1. A017DSX

      Install the jack assembly.

  70. INSTALL JACK CARRIER CUSHION (for LHD)


    1. A017ENI

      Install the jack carrier cushion.

  71. INSTALL JACK CARRIER CUSHION (for RHD)


    1. A017D41

      Install the jack carrier cushion.

  72. INSTALL JACK CARRIER SUPPORT

  73. INSTALL REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)


    1. A017EH1

      Engage the 2 clips and install the rear seat side cover RH.

  74. INSTALL REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)


    1. A017CVI

      Engage the 3 guides and 3 clips and install the rear No. 1 floor board.

  75. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Install the tonneau cover assembly.

  76. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY


    1. A017D36

      Engage the 2 guides and install the No. 2 deck board sub-assembly.

  77. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY


    1. A017F31

      Engage the 2 guides and install the No. 3 deck board sub-assembly.

  78. INSTALL DECK BOARD ASSEMBLY


    1. A017CPI

      Install the deck board sub-assembly.

  79. INSTALL CENTER PILLAR GARNISH LH


    1. A017B73

      Engage the 2 guides and the clip.

    2. Install the center pillar garnish LH with the clip and screw.

  80. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    1. A017G6U

      Install the floor end of the front seat outer belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

    2. Check if the ELR locks.

      Note

      The check should be performed with the outer belt assembly installed.


      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.

  81. INSTALL LOWER CENTER PILLAR GARNISH LH


    1. A017CGP

      Engage the 2 claws and the 2 clips, and install the lower center pillar garnish LH.

  82. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. A017F49E01

      Align the alignment mark (red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  83. INSTALL REAR DOOR SCUFF PLATE LH


    1. A017D4T

      Engage the guide, 3 clips and 5 claws, and install the rear door scuff plate LH.

  84. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A017G63

      Engage the claw and clip, install the cowl side trim sub-assembly LH.

    2. Install the clip.

  85. INSTALL FRONT PILLAR GARNISH LH


    1. A017BX5E01

      Remove the protective cover.

    2. A017BTZE01

      Install a new clip <A> on the front pillar garnish LH.

    3. Engage the 3 guides and 2 clips, then install the front pillar garnish LH.

  86. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. A017EEJE01

      Align the alignment mark (blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  87. INSTALL FRONT DOOR SCUFF PLATE LH


    1. A017B6P

      Engage the guide and the 8 claws, and install the front door scuff plate LH.

  88. INSTALL CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  89. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  90. INSTALL LOWER CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  91. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    1. A017FFPE01

      Align the alignment mark (green) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.

      Note

      After installation, check that the corners fit correctly.

  92. INSTALL REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  93. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  94. INSTALL FRONT PILLAR GARNISH RH


    1. A017B3UE01

      Remove the protective cover.

    2. A017D4XE01

      Install a new clip <A> on the front pillar garnish RH.

    3. Engage the 3 guides and 2 clips, then install the front pillar garnish RH.

  95. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    1. A017D8ZE01

      Align the alignment mark (pink) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

      Note

      After installation, check that the corners fit correctly.

  96. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  97. INSTALL REAR NO. 1 SEAT ASSEMBLY LH


    1. A017FCR

      Temporarily install the 2 bolts on the front side of the seat.

    2. A017BHD

      Temporarily install the 3 bolts on the rear side of the seat.

    3. Install the rear No. 1 seat assembly with the 5 bolts.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

  98. CONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY LH (w/ Remote Folding Function)


    1. Remove the rear seat reclining control cable from the carpet hole.

      A017DSHE01

    2. Connect the rear seat reclining control cable as shown in the illustration.

    3. Connect the rear No. 1 seat lock cable assembly as shown in the illustration.

      A017BYUE01
    4. A017EVX

      Engage the 2 claws and connect the rear No. 1 seat lock cable assembly as shown in the illustration.

    5. Return the seatback to the upright position.

    6. Pull up the adjuster's lock piece to lock it as shown in the illustration.

      A017ENNE01

      Note

      When pressing the lock piece, make sure the adjuster's spring is not compress.

  99. INSPECT REAR SEAT SLIDE ADJUSTER LOCK (for LH Side)


    1. Check that the left and right adjusters lock simultaneously when sliding the seat.

    2. If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.

  100. INSTALL REAR SEAT LEG SIDE COVER LH


    1. A017BXU

      Engage the clip.

    2. Engage the 3 claws and install the rear seat leg side cover.

  101. INSTALL REAR INNER TRACK BRACKET COVER LH


    1. A017FUU

      Engage the 4 claws and install the rear inner track bracket cover.

  102. INSTALL REAR OUTER TRACK BRACKET COVER LH


    1. A017BNT

      Engage the 4 claws and install the rear outer track bracket cover.

  103. INSTALL REAR SEAT TRACK BRACKET COVER LH


    1. A017DZY

      Engage the 8 claws and install the 2 rear seat track bracket covers.

  104. INSTALL REAR SEAT HEADREST ASSEMBLY (for LH Side)

  105. INSTALL REAR CENTER SEAT ASSEMBLY

  106. INSTALL REAR NO. 1 SEAT ASSEMBLY RH


    1. A017D5O

      Temporarily install the 2 bolts on the front side of the seat.

    2. A017EZ3

      Temporarily Install the 3 bolts on the rear side of the seat.

    3. Install the rear No. 1 seat assembly with the 5 bolts.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

  107. CONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY RH (w/ Remote Folding Function)


    1. Remove the rear seat reclining control cable from the carpet hole.

      A017EI7E01

    2. Connect the rear seat reclining control cable as shown in the illustration.

    3. Connect the rear No. 1 seat lock cable assembly as shown in the illustration.

      A017CUJE01
    4. A017COZ

      Engage the 2 claws and connect the rear No. 1 seat lock cable assembly as shown in the illustration.

    5. Return the seatback to the upright position.

    6. Pull up the adjuster's lock piece to lock it as shown in the illustration.

      A017G4AE01

      Note

      When pressing the lock piece, make sure the adjuster's spring is not compress.

  108. INSPECT REAR SEAT SLIDE ADJUSTER LOCK (for RH Side)


    1. Check that the left and right adjusters lock simultaneously when sliding the seat.

    2. If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.

  109. INSTALL REAR SEAT LEG SIDE COVER RH


    1. A017F28

      Engage the clip.

    2. Engage the 3 claws and install the rear seat leg side cover.

  110. INSTALL REAR INNER TRACK BRACKET COVER RH


    1. A017F59

      Engage the 4 claws and install the rear inner track bracket cover.

  111. INSTALL REAR OUTER TRACK BRACKET COVER RH


    1. A017D2L

      Engage the 4 claws and install the rear outer track bracket cover.

  112. INSTALL REAR SEAT TRACK BRACKET COVER RH


    1. A017ERX

      Engage the 8 claws and install the 2 seat track bracket covers.

  113. INSTALL REAR SEAT HEADREST ASSEMBLY (for RH Side)

  114. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  115. INSPECT SRS WARNING LIGHT


    1. Inspect the SRS warning light Click here.