PTC HEATER ASSEMBLY REMOVAL


  1. REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY


    1. A017DDAE01

      Apply protective tape to the areas shown in the illustration.

    2. Using a moulding remover, disengage the 2 claws and 5 clips, and then remove the center instrument panel register assembly as shown in the illustration.

  2. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Smart Entry and Start System)


    1. A017BKEE01

      Apply protective tape to the areas shown in the illustration.

    2. Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.

      Note

      Do not pull on the small storage compartment lid. Doing so may cause damage.

    3. Disconnect each connector and remove the center instrument cluster finish panel assembly.

  3. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/ Smart Entry and Start System)


    1. A017EABE01

      Apply protective tape to the areas shown in the illustration.

    2. Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.

      Note

      Do not pull on the small storage compartment lid. Doing so may cause damage.

    3. Disconnect each connector and remove the center instrument cluster finish panel assembly.

  4. REMOVE HEATER CONTROL AND ACCESSORY ASSEMBLY (for Manual Air Conditioning System)


    1. A017G04

      Disengage the 4 clips and remove the heater control and accessory assembly.

    2. Disconnect the connector.

  5. REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)


    1. A017EE0

      Disengage the 4 clips and remove the air conditioning control assembly.

    2. Disconnect the connector.

  6. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/o Navigation System)


    1. A017FXP

      Remove the 4 bolts.

    2. A017EFV

      Pull the radio receiver assembly with bracket toward the rear of the vehicle and disengage the 4 clips.

    3. Disconnect each connector and remove the radio receiver assembly with bracket.

  7. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)


    1. A017EUS

      Remove the 4 bolts.

    2. A017CTX

      Pull the navigation receiver assembly with bracket toward the rear of the vehicle and disengage the 4 clips.

    3. Disconnect each connector and remove the navigation receiver assembly with bracket.

  8. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY WITH BRACKET (w/o Radio Receiver)


    1. A017C93

      Remove the 4 bolts <D>.

    2. Disengage the 4 clips.

    3. Disconnect each connector and remove the integration control and panel assembly with bracket.

  9. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  10. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  11. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. A017B7A

      Disengage the 3 claws.

    2. Disengage the 2 guides and remove the No. 2 instrument panel under cover sub-assembly.

  12. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    1. A017F5K

      Remove the 2 bolts <B> and 3 screws <F>.

    2. Disengage the 4 claws and 3 clips.

    3. Disconnect each connector and clamp, and remove the lower instrument panel sub-assembly.

  13. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. A017FDP

      Disengage the 4 claws and 4 clips.

    2. Disconnect the connector and remove the upper console panel sub-assembly.

  14. REMOVE LOWER REAR CONSOLE BOX


    1. Remove the lower rear console box.

  15. REMOVE CONSOLE BOX ASSEMBLY


    1. A017C3F

      Remove the 4 bolts and 2 screws.

    2. A017E8O

      Disconnect the connector.

    3. Disengage the 6 claws, and remove the console box assembly.

  16. REMOVE FRONT NO. 2 CONSOLE BOX INSERT


    1. A017BSW

      Using a clip remover, remove the clip.

    2. Remove the 3 screws <F>.

    3. Disengage the claw and 2 guides, and then remove the front No. 2 console box insert.

  17. REMOVE NO. 3 AIR DUCT SUB-ASSEMBLY


    1. A017B6H

      Disengage the 3 claws and remove the No. 3 air duct sub-assembly as shown in the illustration.

  18. REMOVE QUICK HEATER ASSEMBLY


    1. A017BZF

      Disconnect the 2 connectors.

    2. Remove the 3 screws and the quick heater assembly as shown in the illustration.