PTC HEATER ASSEMBLY REMOVAL

REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY

1. 

   Apply protective tape to the areas shown in the illustration.

2. Using a moulding remover, disengage the 2 claws and 5 clips, and then remove the center instrument panel register assembly as shown in the illustration.

REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Smart Entry and Start System)

1. 

   Apply protective tape to the areas shown in the illustration.

2. Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.

   Note:

   Do not pull on the small storage compartment lid. Doing so may cause damage.

3. Disconnect each connector and remove the center instrument cluster finish panel assembly.

REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/ Smart Entry and Start System)

1. 

   Apply protective tape to the areas shown in the illustration.

2. Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.

   Note:

   Do not pull on the small storage compartment lid. Doing so may cause damage.

3. Disconnect each connector and remove the center instrument cluster finish panel assembly.

REMOVE HEATER CONTROL AND ACCESSORY ASSEMBLY (for Manual Air Conditioning System)

1. 

   Disengage the 4 clips and remove the heater control and accessory assembly.

2. Disconnect the connector.

REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)

1. 

   Disengage the 4 clips and remove the air conditioning control assembly.

2. Disconnect the connector.

REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/o Navigation System)

1. 

   Remove the 4 bolts.

2. 

   Pull the radio receiver assembly with bracket toward the rear of the vehicle and disengage the 4 clips.

3. Disconnect each connector and remove the radio receiver assembly with bracket.

REMOVE NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (w/ Navigation System)

1. 

   Remove the 4 bolts.

2. 

   Pull the navigation receiver assembly with bracket toward the rear of the vehicle and disengage the 4 clips.

3. Disconnect each connector and remove the navigation receiver assembly with bracket.

REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY WITH BRACKET (w/o Radio Receiver)

1. 

   Remove the 4 bolts <D>.

2. Disengage the 4 clips.

3. Disconnect each connector and remove the integration control and panel assembly with bracket.

REMOVE FRONT DOOR SCUFF PLATE RH

REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

1. 

   Disengage the 3 claws.

2. Disengage the 2 guides and remove the No. 2 instrument panel under cover sub-assembly.

REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

1. 

   Remove the 2 bolts <B> and 3 screws <F>.

2. Disengage the 4 claws and 3 clips.

3. Disconnect each connector and clamp, and remove the lower instrument panel sub-assembly.

REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY

1. 

   Disengage the 4 claws and 4 clips.

2. Disconnect the connector and remove the upper console panel sub-assembly.

REMOVE LOWER REAR CONSOLE BOX

1. Remove the lower rear console box.

REMOVE CONSOLE BOX ASSEMBLY

1. 

   Remove the 4 bolts and 2 screws.

2. 

   Disconnect the connector.

3. Disengage the 6 claws, and remove the console box assembly.

REMOVE FRONT NO. 2 CONSOLE BOX INSERT

1. 

   Using a clip remover, remove the clip.

2. Remove the 3 screws <F>.

3. Disengage the claw and 2 guides, and then remove the front No. 2 console box insert.