SLIDING ROOF SYSTEM Sliding Roof Control Switch Circuit

DESCRIPTION

The sliding roof drive gear (sliding roof ECU) receives slide switch and tilt switch signals and drives its built-in motor.

WIRING DIAGRAM

A01GMIFE02

INSPECTION PROCEDURE

PROCEDURE


  1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SLIDING ROOF OPERATION)


    1. Select the Active Test, use the intelligent tester to generate a control command, and then check that the sliding roof slides open / close and tilts up / down.


      1. Intelligent tester

        Sliding Roof
        Tester Display Test Part Control Range
        Slide Roof Operate sliding roof SLIDE CLOSE/TILT UP

        CLOS/UP: Sliding roof SLIDE CLOSE or TILT UP operation occurs

        OFF: Sliding roof is not operating
        Slide Roof Operate sliding roof SLIDE OPEN/TILT DOWN

        OPEN/DWN: Sliding roof SLIDE OPEN or TILT DOWN operation occurs

        OFF: Sliding roof is not operating
        OK
        Sliding roof operates normally.

    NG

    REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY Click here

    OK

  2. READ VALUE USING INTELLIGENT TESTER (HALL IC)


    1. Use the Data List to check if the hall ICs are functioning properly.


      1. Intelligent tester

        Sliding Roof
        Item Measurement Item/Range Normal Condition Diagnostic Note
        Hall IC1 Status Hall IC1 status/NORMAL or LOCK

        NORMAL: Hall IC1 is normal.

        LOCK: Hall IC1 is abnormal.

        		 -
        Hall IC1 Pulse Hall IC1 signal/LO or HI

        LO: Hall IC1 output Lo.

        HI: Hall IC1 output Hi.

        		 -
        Hall IC2 Status Hall IC2 status/NORMAL or LOCK

        NORMAL: Hall IC2 is normal.

        LOCK: Hall IC2 is abnormal.

        		 -
        Hall IC2 Pulse Hall IC2 signal/LO or HI

        LO: Hall IC2 output Lo.

        HI: Hall IC2 output Hi.

        		 -
        OK
        Tester displays other than LOCK.

    NG

    REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY Click here

    OK

  3. READ VALUE USING INTELLIGENT TESTER (SLIDING ROOF SWITCH)


    1. Use the Data List to check if the sliding roof switch is functioning properly.


      1. Intelligent tester

        Sliding Roof
        Item Measurement Item/Range Normal Condition Diagnostic Note
        Open Switch Sliding roof switch open signal/ON or OFF

        ON: OPEN switch is pressed

        OFF: OPEN switch is not pressed

        		 -
        Close Switch Sliding roof switch close signal/ON or OFF

        ON: CLOSE switch is pressed

        OFF: CLOSE switch is not pressed

        		 -
        Up Switch Sliding roof switch tilt up signal/ON or OFF

        ON: UP switch is pressed

        OFF: UP switch is not pressed

        		 -
        Down Switch Sliding roof switch tilt down signal/ON or OFF

        ON: DOWN switch is pressed

        OFF: DOWN switch is not pressed

        		 -
        OK
        When the switch is operating, the intelligent tester should display as shown in the table.

    NG

    INSPECT MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH) Click here

    OK

    REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY Click here

  4. INSPECT MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH)

    A01GHNOE01

    1. Remove the map light for standard body Click here or long body Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Switch Condition Specified Condition
      A-24 (UP) - A-16 (GND9) TILT UP Below 1 Ω
      A-24 (UP) - A-16 (GND9) Off 10 kΩ or higher
      A-23 (DOWN) - A-16 (GND9) TILT DOWN Below 1 Ω
      A-23 (DOWN) - A-16 (GND9) Off 10 kΩ or higher
      B-3 (OPN) - A-16 (GND9) SLIDE OPEN Below 1 Ω
      B-3 (OPN) - A-16 (GND9) Off 10 kΩ or higher
      B-12 (CLS) - A-16 (GND9) SLIDE CLOSE Below 1 Ω
      B-12 (CLS) - A-16 (GND9) Off 10 kΩ or higher
      Result
      Result Proceed to
      OK A
      NG (for Standard Body) B
      NG (for Long Body) C

    B

    REPLACE MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH) Click here

    C

    REPLACE MAP LIGHT ASSEMBLY Click here

    A

  5. CHECK HARNESS AND CONNECTOR (MAP LIGHT - SLIDING ROOF DRIVE GEAR AND BODY GROUND)

    A01GI6TE01

    1. Disconnect the X5 drive gear connector.

    2. Disconnect the X4 and X6 map light connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      X5-10 (UP) - X4-24 (UP) Always Below 1 Ω
      X5-8 (DWN) - X4-23 (DOWN) Always Below 1 Ω
      X5-7 (OPN) - X6-3 (OPN) Always Below 1 Ω
      X5-9 (CLS) - X6-12 (CLS) Always Below 1 Ω
      X4-16 (GND9) - Body ground Always Below 1 Ω
      X5-2 (E) - Body ground Always Below 1 Ω
      X5-10 (UP) or X4-24 (UP) - Body ground Always 10 kΩ or higher
      X5-8 (DWN) or X4-23 (DOWN) - Body ground Always 10 kΩ or higher
      X5-7 (OPN) or X6-3 (OPN) - Body ground Always 10 kΩ or higher
      X5-9 (CLS) or X6-12 (CLS) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY Click here