SLIDING ROOF SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the intelligent tester to read the Data List allows the values or states of switches, sensor, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the tester on.

    4. Enter the following menus:


      1. Intelligent tester - Select: Body / Sliding Roof / Data List /

    5. According to the display on tester, read the "Data List".


      1. Intelligent tester

        Sliding Roof
        Tester Display Measurement Item/Range Normal Condition Diagnostic Note
        Open Switch Sliding roof switch open signal/ON or OFF

        ON: OPEN switch is pressed.

        OFF: OPEN switch is not pressed.

        		 -
        Close Switch Sliding roof switch close signal/ON or OFF

        ON: CLOSE switch is pressed.

        OFF: CLOSE switch is not pressed.

        		 -
        Up Switch Sliding roof switch tilt up signal/ON or OFF

        ON: UP switch is pressed.

        OFF: UP switch is not pressed.

        		 -
        Down Switch Sliding roof switch tilt down signal/ON or OFF

        ON: DOWN switch is pressed.

        OFF: DOWN switch is not pressed.

        		 -
        Hall IC1 Status Hall IC1 status/NORMAL or LOCK

        NORMAL: Hall IC1 is normal.

        LOCK: Hall IC1 is abnormal.

        		 -
        Hall IC1 Pulse Hall IC1 signal/LO or HI

        LO: Hall IC1 output Lo.

        HI: Hall IC1 output Hi.

        		 -
        Hall IC2 Status Hall IC2 status/NORMAL or LOCK

        NORMAL: Hall IC2 is normal.

        LOCK: Hall IC2 is abnormal.

        		 -
        Hall IC2 Pulse Hall IC2 signal/LO or HI

        LO: Hall IC2 output Lo.

        HI: Hall IC2 output Hi.

        		 -
        Door Courtesy Driver door courtesy light switch signal/ON or OFF

        ON: Driver door is open.

        OFF: Driver door is closed.

        		 -
        Ignition (MPX) Engine signal (MPX signal)/ON or OFF

        ON: Engine switch on (IG)

        OFF: Engine switch off

        		 -
        Ignition (Direct Signal) Engine switch signal/ON or OFF

        ON: Engine switch on (IG)

        OFF: Engine switch off

        		 -
        Key Off Permission Key-off operation permit signal/ON or OFF

        ON: Driver door is not closed within 45 sec. after engine switch is turned off.

        OFF: Any status except "ON" status

        		 -
        Down Switch Failure(Current) Down switch failure signal (Current)/Fail or Not Fail

        Fail: Sliding roof tilt down signal failure (Current)

        Not Fail: Sliding roof tilt down signal not fail (Current)

        		 -
        Up Switch Failure(Current) Up switch failure signal (Current)/Fail or Not Fail

        Fail: Sliding roof tilt up signal failure (Current)

        Not Fail: Sliding roof tilt up signal not fail (Current)

        		 -
        Close Switch Failure(Current) Close switch failure signal (Current)/Fail or Not Fail

        Fail: Sliding roof close signal failure (Current)

        Not Fail: Sliding roof close signal not fail (Current)

        		 -
        Open Switch Failure(Current) Open switch failure signal (Current)/Fail or Not Fail

        Fail: Sliding roof open signal failure (Current)

        Not Fail: Sliding roof open signal not fail (Current)

        		 -
        Down Switch Failure(Past) Down switch failure signal (Past)/Fail or Not Fail

        Fail: Sliding roof tilt down signal failure (Past)

        Not Fail: Sliding roof tilt down signal not fail (Past)

        		 -
        Up Switch Failure(Past) Up switch failure signal (Past)/Fail or Not Fail

        Fail: Sliding roof tilt up signal failure (Past)

        Not Fail: Sliding roof tilt up signal not fail (Past)

        		 -
        Close Switch Failure(Past) Close switch failure signal (Past)/Fail or Not Fail

        Fail: Sliding roof close signal failure (Past)

        Not Fail: Sliding roof close signal not fail (Past)

        		 -
        Open Switch Failure(Past) Open switch failure signal (Past)/Fail or Not Fail

        Fail: Sliding roof open signal failure (Past)

        Not Fail: Sliding roof open signal not fail (Past)

        		 -
        #Code Number of trouble code Number of trouble code -

  2. ACTIVE TEST

    Tech Tips

    Using the intelligent tester to perform the Active Tests allows relays, VSVs and actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the tester on.

    4. Enter the following menus:


      1. Intelligent tester - Select: Body / Sliding Roof /Active Test /

    5. According to the display on tester, perform the "Active Test".


      1. Intelligent tester

        Sliding Roof
        Tester Display Test Part Control Range Diagnostic Note

        Slide Roof

        (Slide Roof)

        		 Operate sliding roof SLIDE CLOSE/TILT UP

        CLOS/UP: Sliding roof SLIDE CLOSE or TILT UP operation occurs.

        OFF: Sliding roof is not operating

        		 -

        Slide Roof

        (Slide Roof)

        		 Operate sliding roof SLIDE OPEN/TILT DOWN

        OPN/DWN: Sliding roof SLIDE OPEN or TILT DOWN operation occurs

        OFF: Sliding roof is not operating

        		 -