REAR SEATBACK HEATER (for Power Seat) INSTALLATION

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.


  1. INSTALL SEPARATE TYPE REAR SEATBACK COVER LH


    1. Set the separate type rear seatback cover LH in place.

    2. A01GJIKE01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, install the separate type rear seatback cover LH to the rear seatback pad LH with 10 new hog rings.

      Note


      • Be careful not to damage the separate type rear seatback cover LH.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover LH.

  2. INSTALL REAR SEATBACK COVER WITH PAD LH


    1. Set the rear seatback cover with pad LH in place.

    2. Using hog ring pliers, install the rear seatback cover with pad LH to the rear seatback spring assembly LH with 19 new hog rings.

      Note


      • Be careful not to damage the rear seatback cover with pad LH.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the rear seatback cover with pad LH.

    3. Attach the 8 hooks.

    4. Connect the connector.

    5. Attach the seatback cover bracket with the nut.

      Torque:
      5.6 N*m  { 57 kgf*cm, 50 in.*lbf }
      A01GLPEE01
      Text in Illustration
      *1 Seatback Cover Bracket *2 Hook
      *3 Hog Ring Pliers - -

  3. INSTALL REAR SEAT LOCK BASE LH


    1. A01GICD

      Install the rear seat lock base LH with the 3 screws.

  4. INSTALL REAR SEAT COVER CAP LH


    1. A01GIOB

      Attach the 5 claws to install the rear seat cover cap LH.

  5. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY


    1. Attach the guide to install the seat heater control sub-assembly.

    2. Connect the connector.

      Tech Tips

      Use the same procedure to install the seat heater control sub-assembly on the other side.

  6. INSTALL REAR SEAT CLIMATE CONTROL ECU LH

    A01GIJ7

    1. Install the rear seat climate control ECU LH with the 2 nuts.

    2. Connect the 2 connectors.

  7. INSTALL POSITION CONTROL ECU ASSEMBLY

    A01GKJI

    1. Install the position control ECU assembly with the 2 nuts.

    2. Connect the 2 connectors.

      Tech Tips

      Use the same procedure to install the position control ECU assembly on the other side.

  8. INSTALL REAR NO. 1 SEAT HEADREST ADJUSTER SUB-ASSEMBLY

    A01GN9M

    1. Attach the 2 claws to install the rear No. 1 seat headrest adjuster sub-assembly with the 2 bolts.

    2. Connect the 2 connectors and attach the wire harness clamp.

      Tech Tips

      Use the same procedure to install the rear No. 1 seat headrest adjuster sub-assembly on the other side.

  9. INSTALL REAR SEAT HEADREST SUPPORT

    A01GKYP

    1. Attach the 4 claws to install the 2 rear seat headrest supports.

      Tech Tips

      Use the same procedure to install the rear seat headrest support on the other side.

  10. INSTALL REAR SEAT HEADREST ASSEMBLY

    A01GMTN

    1. Install the rear seat headrest assembly with the 2 pins.

      Tech Tips

      Use the same procedure to install the rear seat headrest assembly on the other side.

  11. INSTALL REAR SEAT SHOULDER BELT GUIDE LH

    A01GNCA

    1. Install the rear seat shoulder belt guide LH with the 3 screws.

  12. INSTALL SEPARATE TYPE REAR SEATBACK COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  13. INSTALL REAR SEATBACK COVER WITH PAD RH

    Tech Tips

    Use the same procedures described for the LH side.

  14. INSTALL REAR SEAT LOCK BASE RH

    Tech Tips

    Use the same procedures described for the LH side.

  15. INSTALL REAR SEAT COVER CAP RH

    Tech Tips

    Use the same procedures described for the LH side.

  16. INSTALL REAR SEAT CLIMATE CONTROL ECU RH

    Tech Tips

    Use the same procedures described for the LH side.

  17. INSTALL REAR SEAT SHOULDER BELT GUIDE RH

    Tech Tips

    Use the same procedures described for the LH side.

  18. INSTALL REAR SEATBACK ASSEMBLY LH

    A01GKPGE03

    1. Connect the rear seatback assembly LH to the rear No. 2 seatback adjuster assembly, and press down on the rear seatback assembly LH to install it to the rear No. 2 seatback adjuster assembly. Then connect the air duct to the vehicle body.

      Note

      Be careful not to damage the vehicle body.

    2. Install the 2 nuts.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

    3. Install the clip and attach the 3 pieces of fastening tape.

      Text in Illustration
      *1 Fastening Tape
    4. A01GL9B

      Connect the 3 connectors and attach the 7 wire harness clamps.

    5. A01GN8I

      Connect the 2 connectors.

    6. Install the junction block with the bolt.

      Torque:
      30 N*m  { 306 kgf*cm, 22 ft.*lbf }
    7. A01GMP8

      Connect the seat belt to the shoulder belt guide.

    8. Attach the 2 claws to close the 2 caps.

    9. A01GKCQE03
      Text in Illustration
      *1 Protruding Part

      Connect the anchor part of the rear seat 3 point type belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear seat 3 point type belt assembly to overlap protruding parts of the floor panel.

  19. INSTALL REAR SEATBACK ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  20. INSTALL REAR SEAT CUSHION ASSEMBLY LH


    1. A01GIBQ

      Connect the connector.

    2. Attach the rear hook of the rear seat cushion assembly LH to the rear No. 2 seat adjuster assembly.

      Note

      Be careful not to damage the vehicle body.

    3. Attach the 2 front hooks of the rear seat cushion assembly LH to the rear No. 2 seat adjuster assembly.

  21. INSTALL REAR SEAT CUSHION ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  22. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  23. INSTALL COWL TOP VENTILATOR LOUVER RH


    1. A01GM4S

      for LHD:

      Install the 6 clips and cowl top ventilator louver RH.

      Note

      If the cowl top ventilator louver RH is not properly installed, water may leak into the engine room and cause malfunctions. Therefore, make sure the cowl top ventilator louver RH is installed properly.

    2. A01GI9P

      for RHD:

      Install the 6 clips and cowl top ventilator louver LH.

      Note

      If the cowl top ventilator louver LH is not properly installed, water may leak into the engine room and cause malfunctions. Therefore, make sure the cowl top ventilator louver LH is installed properly.

  24. CHECK SRS WARNING LIGHT

    Click here

  25. CHECK REAR SEAT ASSEMBLY


    1. Check the power seat operation:

      Click here

    2. Check the climate control seat system:

      Click here

    3. Check the seat vibration system:

      Click here