FRONT SEATBACK HEATER INSTALLATION

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.


  1. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    1. Set the separate type front seat back cover in place.

    2. for Sport Package:

      Attach the 4 pieces of fastening tape.

    3. Using hog ring pliers, install the separate type front seat back cover to the front seatback pad with 20 new hog rings as shown in the illustration.

      Note


      • Be careful not to damage the separate type front seat back cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat back cover.

      Tech Tips

      Install the hog rings at the cutouts.

      A01GNCWE01
      Text in Illustration
      *A except Sport Package *B for Sport Package
      *1 Fastening Tape *2 Hog Ring Pliers

  2. INSTALL FRONT SEATBACK FRAME ASSEMBLY LH


    1. A01GJ8L

      Temporarily install the front seatback frame assembly LH with the 4 bolts.

    2. Push the front seatback frame assembly LH towards the rear, and tighten the 4 bolts.

      Torque:
      43 N*m  { 439 kgf*cm, 32 ft.*lbf }

    3. for Driver Side:


      1. A01GJL4

        w/ Active Headrest:

        Attach the 9 clamps and connect the 4 connectors.

      2. A01GI9F

        w/ Pre-crash Intelligent Headrest:

        Attach the 9 clamps and connect the 4 connectors.

    4. for Front Passenger Side:


      1. A01GKKC

        w/ Active Headrest:

        Attach the 9 clamps and connect the 3 connectors.

      2. A01GNWX

        w/ Pre-crash Intelligent Headrest:

        Attach the 9 clamps and connect the 3 connectors.

      3. A01GNKC

        w/ Retractable Headrest:

        Attach the 7 clamps and connect the 2 connectors.

  3. INSTALL FRONT SEATBACK COVER WITH PAD


    1. Set the front seatback cover with pad in place.

    2. A01GKQZ

      Attach the 9 hooks to install the front seatback cover with pad.

    3. Attach the 3 clips.

    4. A01GHW3

      Attach the front seatback cover bracket with the bolt.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

  4. INSTALL POWER SEAT SWITCH ASSEMBLY (w/ Shoulder Switch)


    1. Connect the connector.

    2. A01GMG2

      Attach the 2 claws to install the power seat switch assembly.

  5. INSTALL FRONT SEAT HEADREST SUPPORT

    A01GNJS

    1. Attach the 4 claws to install the 2 front seat headrest supports.

  6. INSTALL FRONT SEAT HEADREST ASSEMBLY


    1. w/ Active Headrest, w/ Pre-crash Intelligent Headrest:


      1. A01GJZS

        Install the front seat headrest assembly with the 2 pins.

        Note

        w/ Active Headrest:

        When replacing a deployed active headrest inflator, always replace it together with the front seat headrest assembly.

    2. w/ Retractable Headrest:

      Install the front seat headrest assembly.

  7. INSTALL FRONT SEAT CUSHION ASSEMBLY LH


    1. A01GMK9E01

      Install the front seat cushion assembly with the 4 bolts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

    2. Attach the hook.

      Text in Illustration
      *1 Hook
    3. A01GKNH

      Attach the hook.

    4. A01GN9U

      Install the 2 clips.

    5. A01GM57

      Connect the connector and attach the 2 wire harness clamps.

    6. A01GKE3

      Connect the connector and attach the wire harness clamp.

    7. A01GMGV

      Connect the connector and attach the wire harness clamp.

    8. Attach the 4 claws to connect duct of the seat climate control blower LH.

    9. A01GKHN

      Connect the connector.

    10. A01GIX7

      Connect the duct of the seat climate control blower LH with the 3 screws.

    11. A01GMM5

      Attach the 2 claws to install the No. 6 air duct.

  8. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH


    1. A01GKI2E01
      Text in Illustration
      *1 Hook
      *2 Wire Harness Clamp

      Connect the connector and attach the wire harness clamp.

    2. Attach the 2 hooks to install the front seatback board sub-assembly LH.

    3. Install the 2 screws.

  9. INSTALL FRONT SEAT INNER CUSHION SHIELD LH

    A01GLX6

    1. Attach the claw to install the front seat inner cushion shield LH.

    2. Install the 3 screws.

  10. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

    A01GLD3E02
    Text in Illustration
    *1 Protruding Part

    1. Install the front seat inner belt assembly LH with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding parts of the front seat adjuster.

    2. Attach the claw to connect the connector.

    3. Attach the 6 wire harness clamps.

    4. Connect the 2 connectors.

      A01GKFRE01
      Text in Illustration
      *A for Driver Side *B for Front Passenger Side

  11. INSTALL FRONT SEAT INNER NO. 1 CUSHION SHIELD LH (for Driver Side)


    1. A01GKLD

      Install the front seat inner No. 1 cushion shield LH with the 3 screws.

  12. INSTALL FRONT SEAT INNER NO. 1 CUSHION SHIELD RH (for Front Passenger Side)


    1. A01GJQ8E01
      Text in Illustration
      *A for Ottoman
      *B except Ottoman

      Install the front seat inner No. 1 cushion shield RH with the 3 screws.

  13. INSTALL FRONT SEAT CUSHION SHIELD LH

    A01GKX7E01

    1. Connect the 2 connectors.

    2. Attach the 2 claws to install the front seat cushion shield LH as indicated by the arrows in the order shown in the illustration.

    3. Install the 3 screws.

    4. A01GHJK

      Attach the rubber band of the front seatback board sub-assembly LH to the front seat adjuster assembly LH.

  14. INSTALL FRONT SEAT ASSEMBLY LH

    Click here

  15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  16. CHECK SRS WARNING LIGHT

    Click here

  17. CHECK FRONT SEAT ASSEMBLY


    1. Check the power seat operation:

      Click here

    2. Check the climate control seat system:

      Click here