FRONT SEATBACK HEATER REMOVAL

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • for Driver Side:

    Operate the power seat switch to move the cushion length adjustment to the foremost position.

  • for Ottoman (Front Passenger Side):

    Operate the power seat switch to move the ottoman to the foremost position.

  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE FRONT SEAT ASSEMBLY LH

    Click here

  4. REMOVE FRONT SEAT CUSHION SHIELD LH


    1. A01GHJK

      Release the rubber bands of the seatback board sub-assembly LH from the front seat adjuster assembly LH.

    2. A01GLS0E01

      Remove the 3 screws.

    3. Detach the 2 claws to remove the front seat cushion shield LH as indicated by the arrows in the order shown in the illustration.

    4. Disconnect the 2 connectors.

  5. REMOVE FRONT SEAT INNER NO. 1 CUSHION SHIELD LH (for Driver Side)

    A01GKLD

    1. Remove the 3 screws and front seat inner No. 1 cushion shield LH.

  6. REMOVE FRONT SEAT INNER NO. 1 CUSHION SHIELD RH (for Front Passenger Side)


    1. A01GJQ8E01
      Text in Illustration
      *A for Ottoman
      *B except Ottoman

      Remove the 3 screws and front seat inner No. 1 cushion shield RH.

  7. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH


    1. Disconnect the 2 connectors.

    2. Detach the 6 wire harness clamps.

    3. Detach the claw and disconnect the connector.

      A01GKFRE01
      Text in Illustration
      *A for Driver Side *B for Front Passenger Side
    4. A01GLJT

      Remove the nut and front seat inner belt assembly LH.

  8. REMOVE FRONT SEAT INNER CUSHION SHIELD LH

    A01GLX6

    1. Remove the 3 screws.

    2. Detach the claw to remove the front seat inner cushion shield LH.

  9. REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY LH


    1. A01GI1EE01
      Text in Illustration
      *1 Hook
      *2 Wire Harness Clamp

      Remove the 2 screws.

    2. Detach the 2 hooks.

    3. Detach the wire harness clamp and disconnect the connector to remove the front seatback board sub-assembly LH.

  10. REMOVE FRONT SEAT CUSHION ASSEMBLY LH


    1. A01GMM5

      Detach the 2 claws to remove the No. 6 air duct.

    2. A01GIX7

      Remove the 3 screws and disconnect the duct of the seat climate control blower LH.

    3. A01GKHN

      Disconnect the connector.

    4. A01GMGV

      Detach the 4 claws to disconnect the duct of the seat climate control blower LH.

    5. Disconnect the connector and detach the wire harness clamp.

    6. A01GKE3

      Disconnect the connector and detach the wire harness clamp.

    7. A01GM57

      Disconnect the connector and detach the 2 wire harness clamps.

    8. A01GN9U

      Remove the 2 clips.

    9. A01GKNH

      Detach the hook.

    10. A01GMK9E01
      Text in Illustration
      *1 Hook

      Detach the hook and remove the 4 bolts to remove the front seat cushion assembly LH.

  11. REMOVE FRONT SEAT HEADREST ASSEMBLY


    1. w/ Active Headrest, w/ Pre-crash Intelligent Headrest:


      1. A01GMEV

        Remove the 2 pins and front seat headrest assembly.

        Note

        w/ Active Headrest:

        When replacing a deployed active headrest inflator, always replace it together with the front seat headrest assembly.

    2. w/ Retractable Headrest:

      Pull up the front seat headrest assembly to remove it.

      Note

      As the front seat headrest assembly is tightly fitted to the seat, be careful not to damage the seat when removing the front seat headrest assembly.

  12. REMOVE FRONT SEAT HEADREST SUPPORT

    A01GNJS

    1. Detach the 4 claws to remove the 2 front seat headrest supports.

  13. REMOVE POWER SEAT SWITCH ASSEMBLY (w/ Shoulder Switch)


    1. A01GMG2

      Detach the 2 claws.

    2. Disconnect the connector to remove the power seat switch assembly.

  14. REMOVE FRONT SEATBACK COVER WITH PAD


    1. A01GHW3

      Remove the bolt to detach the front seatback cover bracket.

    2. A01GKQZ

      Remove the 3 clips.

    3. Detach the 9 hooks to remove the seatback cover with pad from the front seat seatback frame assembly LH.

  15. REMOVE FRONT SEATBACK FRAME ASSEMBLY LH


    1. for Driver Side:


      1. A01GJL4

        w/ Active Headrest:

        Disconnect the 4 connectors and detach the 9 clamps.

      2. A01GI9F

        w/ Pre-crash Intelligent Headrest:

        Disconnect the 4 connectors and detach the 9 clamps.

    2. for Front Passenger Side:


      1. A01GKKC

        w/ Active Headrest:

        Disconnect the 3 connectors and detach the 9 clamps.

      2. A01GNWX

        w/ Pre-crash Intelligent Headrest:

        Disconnect the 3 connectors and detach the 9 clamps.

      3. A01GNKC

        w/ Retractable Headrest:

        Disconnect the 2 connectors and detach the 7 clamps.

    3. A01GJ8L

      Remove the 4 bolts and front seat seatback frame assembly LH.

  16. REMOVE SEPARATE TYPE FRONT SEATBACK COVER


    1. except Sport Package:

      Remove the 20 hog rings and separate type front seatback cover.

    2. for Sport Package:

      Detach the 4 pieces of fastening tape to remove the 20 hog rings and separate type front seatback cover.

      A01GIWAE01
      Text in Illustration
      *A except Sport Package *B for Sport Package
      *1 Fastening Tape - -