LUMBAR SUPPORT ADJUSTER ASSEMBLY (for Ottoman) INSTALLATION

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips

Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.

INSTALL REAR SEATBACK SPRING ASSEMBLY LH

Attach the 8 hooks.
Connect the connector.
Using hog ring pliers, install the rear seatback spring assembly LH (lumbar support adjuster LH) to the rear seatback cover with pad with 19 new hog rings.
Note
- Be careful not to damage the rear seatback cover with pad.
- Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the rear seatback cover with pad.

Attach the seatback cover bracket with the nut.

Torque:: 5.6 N*m { 57 kgf*cm, 50 in.*lbf }

Text in Illustration
*1	Seatback Cover Bracket	*2	Hook
*3	Hog Ring Pliers	-	-

INSTALL REAR SEAT LOCK BASE LH
1. Install the rear seat lock base LH with the 3 screws.
INSTALL REAR SEAT COVER CAP LH
1. Attach the 5 claws to install the rear seat cover cap LH.
INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY
1. Attach the guide to install the seat heater control sub-assembly.
2. Connect the connector.
  
  Tech Tips
  
  Use the same procedure to install the seat heater control sub-assembly on the other side.
INSTALL REAR SEAT CLIMATE CONTROL ECU LH
1. Install the rear seat climate control ECU LH with the 2 nuts.
2. Connect the 2 connectors.
INSTALL POSITION CONTROL ECU ASSEMBLY
1. Install the position control ECU assembly with the 2 nuts.
2. Connect the 2 connectors.
  
  Tech Tips
  
  Use the same procedure to install the position control ECU assembly on the other side.
INSTALL REAR NO. 1 SEAT HEADREST ADJUSTER SUB-ASSEMBLY
1. Attach the 2 claws to install the rear No. 1 seat headrest adjuster sub-assembly LH with the 2 bolts.
2. Connect the 2 connectors and attach the wire harness clamp.
  
  Tech Tips
  
  Use the same procedure to install the rear No. 1 seat headrest adjuster sub-assembly on the other side.
INSTALL REAR SEAT HEADREST SUPPORT
1. Attach the 4 claws to install the 2 rear seat headrest supports.
  
  Tech Tips
  
  Use the same procedure to install the rear seat headrest support on the other side.
INSTALL REAR SEAT HEADREST ASSEMBLY
1. Install the rear seat headrest assembly LH with the 2 pins.
  
  Tech Tips
  
  Use the same procedure to install the rear seat headrest assembly on the other side.
INSTALL REAR SEAT SHOULDER BELT GUIDE LH
1. Install the rear seat shoulder belt guide LH with the 3 screws.

INSTALL REAR SEATBACK SPRING ASSEMBLY RH

Attach the 7 hooks and connect the connector.
Set the rear seatback cover with pad RH in place.
Using hog ring pliers, install the rear seatback spring assembly RH (lumbar support adjuster RH) to the rear seatback cover with pad RH with 20 new hog rings.
Note
- Be careful not to damage the rear seatback cover with pad RH.
- Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the rear seatback cover with pad RH.

Attach the seatback cover bracket with the nut.

Torque:: 5.6 N*m { 57 kgf*cm, 50 in.*lbf }

Text in Illustration
*1	Seatback Cover Bracket	*2	Hook
*3	Hog Ring Pliers	-	-

INSTALL REAR SEATBACK CLIMATE CONTROL BLOWER RH

Tech Tips

Use the same procedures described for the LH side.
INSTALL REAR SEAT LOCK BASE RH

Tech Tips

Use the same procedures described for the LH side.
INSTALL REAR SEAT COVER CAP RH

Tech Tips

Use the same procedures described for the LH side.
INSTALL REAR SEAT CLIMATE CONTROL ECU RH

Tech Tips

Use the same procedures described for the LH side.
INSTALL REAR SEAT SHOULDER BELT GUIDE RH

Tech Tips

Use the same procedures described for the LH side.
INSTALL REAR SEATBACK ASSEMBLY LH
1. Connect the rear seatback assembly LH to the rear No. 2 seatback adjuster assembly, and press down on the rear seatback assembly LH to install it to the rear No. 2 seatback adjuster assembly. Then connect the air duct to the vehicle body.
  
  Note
  
  Be careful not to damage the vehicle body.
2. Install the rear seatback assembly LH to the rear No. 2 seatback adjuster assembly with the 2 nuts.
  
  Torque:
  
  20 N*m { 204 kgf*cm, 15 ft.*lbf }
3. Install the clip and attach the 3 pieces of fastening tape.
  
  Text in Illustration
  
  *1 Fastening Tape
4. Connect the 3 connectors and attach the 7 wire harness clamps.
5. Connect the 2 connectors.
6. Install the junction block with the bolt.
  
  Torque:
  
  30 N*m { 306 kgf*cm, 22 ft.*lbf }
7. Connect the rear seat 3 point type belt assembly LH to the rear seat shoulder belt guide LH.
8. Attach the 2 claws to close the 2 caps.
9. Text in Illustration
  
  *1 Protruding Part
  
  Connect the anchor part of the rear seat 3 point type belt assembly LH with the bolt.
  
  Torque:
  
  42 N*m { 428 kgf*cm, 31 ft.*lbf }
  
  Note
  
  Do not allow the anchor part of the rear seat 3 point type belt assembly to overlap protruding parts of the floor panel.

Text in Illustration
*1	Fastening Tape

Text in Illustration
*1	Protruding Part

INSTALL REAR SEATBACK ASSEMBLY RH

Connect the rear seatback assembly RH to the rear No. 2 seat adjuster assembly, and press down on the rear seatback assembly RH to install it to the rear No. 2 seat adjuster assembly. Then connect the air duct to the vehicle body.

Note

Be careful not to damage the vehicle body.
Install the rear seatback assembly RH to the rear No. 2 seat adjuster assembly with the 2 nuts.

Torque:

20 N*m { 204 kgf*cm, 15 ft.*lbf }
Attach the clip and 3 pieces of fastening tape.

Attach the 2 claws to connect the air hose.

Text in Illustration
*1	Air Hose
*2	Fastening Tape
*3	Air Duct

Install the nut.
Connect the 3 connectors and attach the 6 wire harness clamps.
Connect the 3 connectors.
Install the junction block with the bolt.

Torque:

30 N*m { 306 kgf*cm, 22 ft.*lbf }
Install the rear seat 3 point type belt assembly RH to the rear seat shoulder belt guide RH.
Attach the 2 claws to close the 2 caps.
Text in Illustration

*1 Protruding Part

Connect the anchor part of the rear seat 3 point type belt assembly RH with the bolt.

Torque:

42 N*m { 428 kgf*cm, 31 ft.*lbf }

Note

Do not allow the anchor part of the rear seat 3 point type belt assembly RH to overlap protruding parts of the floor panel.

INSTALL REAR CONSOLE BOX (w/ Rear Console Box)

Click here
INSTALL REAR SEAT CENTER ARMREST ASSEMBLY (w/ Center Seat)
1. Connect the 2 connectors.
2. Install the rear seat center armrest assembly with the 2 bolts and nut.
  
  Torque:
  
  20 N*m { 204 kgf*cm, 15 ft.*lbf }
  
  Note
  
  Be careful not to damage the vehicle body.
3. Attach the hook to the center seatback frame wire.
4. Attach the 2 clips to install the rear seat armrest hole board.
5. While pressing the button, lower the rear center seat headrest assembly.
6. Raise the rear seat center armrest assembly.
INSTALL REAR CENTER SEAT CUSHION ASSEMBLY (w/ Center Seat)
1. Attach the rear hook of the center seat cushion assembly to the center seatback frame sub-assembly.
  
  Note
  
  Be careful not to damage the vehicle body.
2. Attach the front hook of the rear center seat cushion assembly to the vehicle body.
INSTALL REAR SEAT CUSHION ASSEMBLY LH
1. Connect the connector.
2. Attach the rear hook of the rear seat cushion assembly LH to the rear seatback frame assembly LH.
  
  Note
  
  Be careful not to damage the vehicle body.
3. Attach the 2 front hooks of the rear seat cushion assembly LH to the rear No. 2 seat adjuster assembly.

Text in Illustration
*1	Protruding Part

INSTALL REAR SEAT CUSHION ASSEMBLY RH

Connect the cable to the negative (-) battery terminal.
Operate the ottoman switch to move the ottoman to the return position.
Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

Text in Illustration
*1	Seat Cover Hook
*2	Nut
*3	Rear Seat Cushion Lock Hook
*4	Rear Hook

Connect the connector.

Attach the rear hook of the rear seat cushion assembly RH to the rear seatback spring assembly RH.

Note

Be careful not to damage the vehicle body.
Attach the 2 front hooks of the rear seat cushion assembly RH to the the rear No. 1 seat adjuster assembly.
Connect the 2 rear seat cushion lock hooks.
Connect the seat cushion ottoman part with the 2 nuts.
Install the 2 seat cushion cover hooks.

CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
INSTALL COWL TOP VENTILATOR LOUVER RH
1. for LHD:
  
  Install the 6 clips and cowl top ventilator louver RH.
  
  Note
  
  If the cowl top ventilator louver RH is not properly installed, water may leak into the engine room and cause malfunctions. Therefore, make sure the cowl top ventilator louver RH is installed properly.
2. for RHD:
  
  Install the 6 clips and cowl top ventilator louver LH.
  
  Note
  
  If the cowl top ventilator louver LH is not properly installed, water may leak into the engine room and cause malfunctions. Therefore, make sure the cowl top ventilator louver LH is installed properly.
CHECK SRS WARNING LIGHT

Click here
CHECK REAR SEAT ASSEMBLY
1. Check the power seat operation:
  
  Click here
2. Check the climate control seat system:
  
  Click here
3. Check the seat vibration system:
  
  Click here