LUMBAR SUPPORT ADJUSTER ASSEMBLY (for Ottoman) INSTALLATION

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. INSTALL REAR SEATBACK SPRING ASSEMBLY LH


    1. Attach the 8 hooks.

    2. Connect the connector.

    3. Using hog ring pliers, install the rear seatback spring assembly LH (lumbar support adjuster LH) to the rear seatback cover with pad with 19 new hog rings.

      Note


      • Be careful not to damage the rear seatback cover with pad.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the rear seatback cover with pad.

    4. Attach the seatback cover bracket with the nut.

      Torque:
      5.6 N*m  { 57 kgf*cm, 50 in.*lbf }
      A01GLPEE01
      Text in Illustration
      *1 Seatback Cover Bracket *2 Hook
      *3 Hog Ring Pliers - -

  2. INSTALL REAR SEAT LOCK BASE LH


    1. A01GICD

      Install the rear seat lock base LH with the 3 screws.

  3. INSTALL REAR SEAT COVER CAP LH


    1. A01GIOB

      Attach the 5 claws to install the rear seat cover cap LH.

  4. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY


    1. Attach the guide to install the seat heater control sub-assembly.

    2. Connect the connector.

      Tech Tips

      Use the same procedure to install the seat heater control sub-assembly on the other side.

  5. INSTALL REAR SEAT CLIMATE CONTROL ECU LH

    A01GIJ7

    1. Install the rear seat climate control ECU LH with the 2 nuts.

    2. Connect the 2 connectors.

  6. INSTALL POSITION CONTROL ECU ASSEMBLY

    A01GKJI

    1. Install the position control ECU assembly with the 2 nuts.

    2. Connect the 2 connectors.

      Tech Tips

      Use the same procedure to install the position control ECU assembly on the other side.

  7. INSTALL REAR NO. 1 SEAT HEADREST ADJUSTER SUB-ASSEMBLY

    A01GN9M

    1. Attach the 2 claws to install the rear No. 1 seat headrest adjuster sub-assembly LH with the 2 bolts.

    2. Connect the 2 connectors and attach the wire harness clamp.

      Tech Tips

      Use the same procedure to install the rear No. 1 seat headrest adjuster sub-assembly on the other side.

  8. INSTALL REAR SEAT HEADREST SUPPORT

    A01GKYP

    1. Attach the 4 claws to install the 2 rear seat headrest supports.

      Tech Tips

      Use the same procedure to install the rear seat headrest support on the other side.

  9. INSTALL REAR SEAT HEADREST ASSEMBLY

    A01GMTN

    1. Install the rear seat headrest assembly LH with the 2 pins.

      Tech Tips

      Use the same procedure to install the rear seat headrest assembly on the other side.

  10. INSTALL REAR SEAT SHOULDER BELT GUIDE LH

    A01GNCA

    1. Install the rear seat shoulder belt guide LH with the 3 screws.

  11. INSTALL REAR SEATBACK SPRING ASSEMBLY RH


    1. Attach the 7 hooks and connect the connector.

    2. Set the rear seatback cover with pad RH in place.

    3. Using hog ring pliers, install the rear seatback spring assembly RH (lumbar support adjuster RH) to the rear seatback cover with pad RH with 20 new hog rings.

      Note


      • Be careful not to damage the rear seatback cover with pad RH.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the rear seatback cover with pad RH.

    4. Attach the seatback cover bracket with the nut.

      Torque:
      5.6 N*m  { 57 kgf*cm, 50 in.*lbf }
      A01GJADE02
      Text in Illustration
      *1 Seatback Cover Bracket *2 Hook
      *3 Hog Ring Pliers - -

  12. INSTALL REAR SEATBACK CLIMATE CONTROL BLOWER RH

    Tech Tips

    Use the same procedures described for the LH side.

  13. INSTALL REAR SEAT LOCK BASE RH

    Tech Tips

    Use the same procedures described for the LH side.

  14. INSTALL REAR SEAT COVER CAP RH

    Tech Tips

    Use the same procedures described for the LH side.

  15. INSTALL REAR SEAT CLIMATE CONTROL ECU RH

    Tech Tips

    Use the same procedures described for the LH side.

  16. INSTALL REAR SEAT SHOULDER BELT GUIDE RH

    Tech Tips

    Use the same procedures described for the LH side.

  17. INSTALL REAR SEATBACK ASSEMBLY LH

    A01GKZ2E01

    1. Connect the rear seatback assembly LH to the rear No. 2 seatback adjuster assembly, and press down on the rear seatback assembly LH to install it to the rear No. 2 seatback adjuster assembly. Then connect the air duct to the vehicle body.

      Note

      Be careful not to damage the vehicle body.

    2. Install the rear seatback assembly LH to the rear No. 2 seatback adjuster assembly with the 2 nuts.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

    3. Install the clip and attach the 3 pieces of fastening tape.

      Text in Illustration
      *1 Fastening Tape
    4. A01GL9B

      Connect the 3 connectors and attach the 7 wire harness clamps.

    5. A01GN8I

      Connect the 2 connectors.

    6. Install the junction block with the bolt.

      Torque:
      30 N*m  { 306 kgf*cm, 22 ft.*lbf }
    7. A01GMP8

      Connect the rear seat 3 point type belt assembly LH to the rear seat shoulder belt guide LH.

    8. Attach the 2 claws to close the 2 caps.

    9. A01GKCQE03
      Text in Illustration
      *1 Protruding Part

      Connect the anchor part of the rear seat 3 point type belt assembly LH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear seat 3 point type belt assembly to overlap protruding parts of the floor panel.

  18. INSTALL REAR SEATBACK ASSEMBLY RH

    A01GM7AE01

    1. Connect the rear seatback assembly RH to the rear No. 2 seat adjuster assembly, and press down on the rear seatback assembly RH to install it to the rear No. 2 seat adjuster assembly. Then connect the air duct to the vehicle body.

      Note

      Be careful not to damage the vehicle body.

    2. Install the rear seatback assembly RH to the rear No. 2 seat adjuster assembly with the 2 nuts.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

    3. Attach the clip and 3 pieces of fastening tape.

    4. Attach the 2 claws to connect the air hose.

      Text in Illustration
      *1 Air Hose
      *2 Fastening Tape
      *3 Air Duct

    5. Install the nut.

    6. A01GLLP

      Connect the 3 connectors and attach the 6 wire harness clamps.

    7. A01GI1Y

      Connect the 3 connectors.

    8. Install the junction block with the bolt.

      Torque:
      30 N*m  { 306 kgf*cm, 22 ft.*lbf }
    9. A01GI77

      Install the rear seat 3 point type belt assembly RH to the rear seat shoulder belt guide RH.

    10. Attach the 2 claws to close the 2 caps.

    11. A01GJ62E02
      Text in Illustration
      *1 Protruding Part

      Connect the anchor part of the rear seat 3 point type belt assembly RH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear seat 3 point type belt assembly RH to overlap protruding parts of the floor panel.

  19. INSTALL REAR CONSOLE BOX (w/ Rear Console Box)

    Click here

  20. INSTALL REAR SEAT CENTER ARMREST ASSEMBLY (w/ Center Seat)


    1. A01GJRU

      Connect the 2 connectors.

    2. Install the rear seat center armrest assembly with the 2 bolts and nut.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

      Note

      Be careful not to damage the vehicle body.

    3. A01GLDME03

      Attach the hook to the center seatback frame wire.

    4. Attach the 2 clips to install the rear seat armrest hole board.

    5. A01GIIY

      While pressing the button, lower the rear center seat headrest assembly.

    6. Raise the rear seat center armrest assembly.

  21. INSTALL REAR CENTER SEAT CUSHION ASSEMBLY (w/ Center Seat)


    1. A01GJWX

      Attach the rear hook of the center seat cushion assembly to the center seatback frame sub-assembly.

      Note

      Be careful not to damage the vehicle body.

    2. Attach the front hook of the rear center seat cushion assembly to the vehicle body.

  22. INSTALL REAR SEAT CUSHION ASSEMBLY LH


    1. A01GIBQ

      Connect the connector.

    2. Attach the rear hook of the rear seat cushion assembly LH to the rear seatback frame assembly LH.

      Note

      Be careful not to damage the vehicle body.

    3. Attach the 2 front hooks of the rear seat cushion assembly LH to the rear No. 2 seat adjuster assembly.

  23. INSTALL REAR SEAT CUSHION ASSEMBLY RH


    1. Connect the cable to the negative (-) battery terminal.

    2. Operate the ottoman switch to move the ottoman to the return position.

    3. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    4. A01GMJ8E02
      Text in Illustration
      *1 Seat Cover Hook
      *2 Nut
      *3 Rear Seat Cushion Lock Hook
      *4 Rear Hook

      Connect the connector.

    5. Attach the rear hook of the rear seat cushion assembly RH to the rear seatback spring assembly RH.

      Note

      Be careful not to damage the vehicle body.

    6. Attach the 2 front hooks of the rear seat cushion assembly RH to the the rear No. 1 seat adjuster assembly.

    7. Connect the 2 rear seat cushion lock hooks.

    8. Connect the seat cushion ottoman part with the 2 nuts.

    9. Install the 2 seat cushion cover hooks.

  24. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  25. INSTALL COWL TOP VENTILATOR LOUVER RH


    1. A01GM4S

      Install the 6 clips and cowl top ventilator louver RH.

      Note

      If the cowl top ventilator louver RH is not properly installed, water may leak into the engine room and cause malfunctions. Therefore, make sure the cowl top ventilator louver RH is installed properly.

  26. CHECK SRS WARNING LIGHT

    Click here

  27. CHECK REAR SEAT ASSEMBLY


    1. Check the power seat operation:

      Click here

    2. Check the climate control seat system:

      Click here

    3. Check the seat vibration system:

      Click here