FRONT POWER SEAT MOTOR ASSEMBLY REMOVAL

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • for Driver Side:

    Operate the power seat switch to move the cushion length adjustment to the foremost position.

  • for Ottoman (Front Passenger Side):

    Operate the power seat switch to move the ottoman to the foremost position.

  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. REMOVE COWL TOP VENTILATOR LOUVER RH

    A01GM4S

    1. Remove the 6 clips and cowl top ventilator louver RH.

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE FRONT SEAT ASSEMBLY LH

    Click here

  5. REMOVE FRONT SEAT CUSHION SHIELD LH


    1. A01GHJK

      Release the rubber bands of the seatback board sub-assembly LH from the front seat adjuster assembly LH.

    2. A01GLS0E01

      Remove the 3 screws.

    3. Detach the 2 claws to remove the front seat cushion shield LH as indicated by the arrows in the order shown in the illustration.

    4. Disconnect the 2 connectors.

  6. REMOVE FRONT SEAT INNER NO. 1 CUSHION SHIELD LH (for Driver Side)

    A01GKLD

    1. Remove the 3 screws and front seat inner No. 1 cushion shield LH.

  7. REMOVE FRONT SEAT INNER NO. 1 CUSHION SHIELD RH (for Front Passenger Side)


    1. A01GJQ8E01
      Text in Illustration
      *A for Ottoman
      *B except Ottoman

      Remove the 3 screws and front seat inner No. 1 cushion shield RH.

  8. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH


    1. Disconnect the 2 connectors.

    2. Detach the 6 wire harness clamps.

    3. Detach the claw and disconnect the connector.

      A01GKFRE01
      Text in Illustration
      *A for Driver Side *B for Front Passenger Side
    4. A01GLJT

      Remove the nut and front seat inner belt assembly LH.

  9. REMOVE FRONT SEAT INNER CUSHION SHIELD LH

    A01GLX6

    1. Remove the 3 screws.

    2. Detach the claw to remove the front seat inner cushion shield LH.

  10. REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY LH


    1. A01GI1EE01
      Text in Illustration
      *1 Hook
      *2 Wire Harness Clamp

      Remove the 2 screws.

    2. Detach the 2 hooks.

    3. Detach the wire harness clamp and disconnect the connector to remove the front seatback board sub-assembly LH.

  11. REMOVE FRONT SEAT CUSHION ASSEMBLY LH


    1. A01GMM5

      Detach the 2 claws to remove the No. 6 air duct.

    2. A01GIX7

      Remove the 3 screws and disconnect the duct of the seat climate control blower LH.

    3. A01GKHN

      Disconnect the connector.

    4. A01GMGV

      Detach the 4 claws to disconnect the duct of the seat climate control blower LH.

    5. Disconnect the connector and detach the wire harness clamp.

    6. A01GKE3

      Disconnect the connector and detach the wire harness clamp.

    7. A01GM57

      Disconnect the connector and detach the 2 wire harness clamps.

    8. A01GN9U

      Remove the 2 clips.

    9. A01GKNH

      Detach the hook.

    10. A01GMK9E01
      Text in Illustration
      *1 Hook

      Detach the hook and remove the 4 bolts to remove the front seat cushion assembly LH.

  12. REMOVE FRONT SEAT HEADREST ASSEMBLY


    1. w/ Active Headrest, w/ Pre-crash Intelligent Headrest:


      1. A01GMEV

        Remove the 2 pins and front seat headrest assembly.

        Note

        w/ Active Headrest:

        When replacing a deployed active headrest inflator, always replace it together with the front seat headrest assembly.

    2. w/ Retractable Headrest:

      Pull up the front seat headrest assembly to remove it.

      Note

      As the front seat headrest assembly is tightly fitted to the seat, be careful not to damage the seat when removing the front seat headrest assembly.

  13. REMOVE FRONT SEAT HEADREST SUPPORT

    A01GNJS

    1. Detach the 4 claws to remove the 2 front seat headrest supports.

  14. REMOVE POWER SEAT SWITCH ASSEMBLY (w/ Shoulder Switch)


    1. A01GMG2

      Detach the 2 claws.

    2. Disconnect the connector to remove the power seat switch assembly.

  15. REMOVE FRONT SEATBACK COVER WITH PAD


    1. A01GHW3

      Remove the bolt to detach the front seatback cover bracket.

    2. A01GKQZ

      Remove the 3 clips.

    3. Detach the 9 hooks to remove the seatback cover with pad from the front seat seatback frame assembly LH.

  16. REMOVE ACTIVE HEADREST INFLATOR (w/ Active Headrest)


    1. A01GHJME01
      Text in Illustration
      *1 Guide
      *2 Clamp

      Disconnect the connector.

      Note

      When handling the airbag connector, take care not to damage the airbag wire harness.

    2. Remove the bolt and nut.

    3. Detach the guide and 2 clamps.

    4. Turn the active headrest inflator in the direction indicated by the arrow to remove it.

  17. REMOVE FRONT SEAT HEADREST ADJUSTER SUB-ASSEMBLY


    1. w/ Active Headrest:


      1. A01GIXX

        Detach the 2 wire harness clamps and disconnect the connector.

      2. A01GJNB

        Remove the 2 bolts.

      3. Detach the 2 claws and remove the headrest adjuster.

    2. w/ Pre-crash Intelligent Headrest:


      1. A01GIXX

        Detach the 2 wire harness clamps and disconnect the connector.

      2. A01GLY9

        Detach the 4 wire harness clamps and remove the 2 bolts.

      3. Detach the 2 claws and remove the headrest adjuster.

      4. A01GNWW

        Remove the screw.

      5. Detach the guide and remove the plate.

      6. A01GLQY

        Detach the 2 claws and disconnect the connector from the connector holder.

    3. w/ Retractable Headrest:


      1. A01GMMS

        Remove the 2 screws and headrest motor from the seatback frame.

      2. Remove the 4 bolts.

      3. Detach the 2 claws and remove the headrest adjuster.

      4. A01GMDL

        Detach the 2 claws and remove the motor.

      5. A01GJBP

        Detach the 2 claws and remove the cable.

      6. A01GLZC

        Remove the 2 screws and headrest stay cover.

  18. REMOVE FRONT SEATBACK FRAME ASSEMBLY LH


    1. for Driver Side:


      1. A01GJL4

        w/ Active Headrest:

        Disconnect the 4 connectors and detach the 9 clamps.

      2. A01GI9F

        w/ Pre-crash Intelligent Headrest:

        Disconnect the 4 connectors and detach the 9 clamps.

    2. for Front Passenger Side:


      1. A01GKKC

        w/ Active Headrest:

        Disconnect the 3 connectors and detach the 9 clamps.

      2. A01GNWX

        w/ Pre-crash Intelligent Headrest:

        Disconnect the 3 connectors and detach the 9 clamps.

      3. A01GNKC

        w/ Retractable Headrest:

        Disconnect the 2 connectors and detach the 7 clamps.

    3. A01GJ8L

      Remove the 4 bolts and front seat seatback frame assembly LH.

  19. REMOVE RECLINING ADJUSTER INSIDE COVER LH


    1. A01GMIZ

      Remove the screw and reclining adjuster inside cover LH.

    2. Detach the wire harness clamp.

  20. REMOVE RECLINING ADJUSTER INSIDE COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  21. REMOVE FRONT SEAT LOWER CUSHION SHIELD

    A01GJNE

    1. Remove the 4 nuts and front seat lower cushion shield.

  22. REMOVE FRONT SEAT CUSHION SPRING


    1. A01GKGM

      Remove the front seat cushion spring.

      Tech Tips

      Use the same procedure to remove the front seat cushion spring on the other side.

  23. REMOVE NO. 1 SEAT CUSHION PLATE

    A01GLID

    1. Remove the 2 bolts and No. 1 seat cushion plate.

  24. REMOVE FRONT NO. 2 SEAT TRAVEL LINK

    A01GKX9

    1. Remove the bolt and front No. 2 seat travel link.

  25. REMOVE FRONT NO. 1 SEAT TRAVEL LINK

    Tech Tips

    Use the same procedures described for the No. 2 seat travel link.

  26. REMOVE FRONT SEAT CLIMATE CONTROL ECU LH

    A01GLRI

    1. Disconnect the 2 connectors.

    2. Remove the 2 bolts and front seat climate control ECU LH.

  27. REMOVE SEAT CLIMATE CONTROL BLOWER LH

    A01GN3Q

    1. Detach the 4 claws and disconnect the climate control duct.

    2. Detach the 2 wire harness clamps and disconnect the connector.

    3. Remove the 2 bolts and seat climate control blower LH.

  28. REMOVE SEAT POSITION AIRBAG SENSOR


    1. A01GJD0E02

      Using a T30 "TORX" socket wrench, remove the "TORX" screw and seat position sensor with sensor protector.

    2. Disconnect the connector.

    3. A01GKAHE04

      Remove the seat slide position sensor protector from the seat position sensor.

  29. REMOVE FRONT SEAT WIRE LH


    1. Remove the bolt.

    2. Disconnect the 4 connectors.

    3. Detach the 13 wire harness clamps to remove the front seat wire LH.

      A01GJAC