REAR SEAT ASSEMBLY (for Ottoman) INSTALLATION

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.


  1. INSTALL REAR SEAT RECLINING ADJUSTER ASSEMBLY LH

    A01GJNO

    1. Install the rear seat reclining adjuster assembly LH with the 4 nuts.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

      Note

      Be careful not to damage the vehicle body.

  2. INSTALL REAR SEAT RECLINING ADJUSTER ASSEMBLY RH

    A01GM6B

    1. Install the rear seat reclining adjuster assembly RH with the 4 nuts.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

      Note

      Be careful not to damage the vehicle body.

    2. Connect the connector.

  3. INSTALL REAR NO. 2 SEAT ADJUSTER ASSEMBLY


    1. A01GJM1E02

      Connect the air duct to the vehicle body.

    2. Install the rear No. 2 seat adjuster assembly with the 4 bolts and nut.

      Torque:
      for bolt A
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
      except bolt A
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

      Note

      Be careful not to damage the vehicle body.

    3. A01GJIQE03
      Text in Illustration
      *1 Protruding Part

      w/ Center Seat:

      Connect the anchor part of the rear center seat outer belt assembly with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear center seat outer belt assembly to overlap the protruding part of the anchor bracket.

  4. INSTALL REAR NO. 1 SEAT ADJUSTER ASSEMBLY


    1. A01GISWE01

      Connect the air duct to the vehicle body.

    2. Install the rear No. 1 seat adjuster assembly with the 4 bolts and nut.

      Torque:
      for bolt A
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
      except bolt A
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

      Note

      Be careful not to damage the vehicle body.

  5. INSTALL REAR CENTER SEAT INNER BELT ASSEMBLY (w/ Center Seat)

    A01GNXDE01

    1. Install the rear center seat inner belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear center seat inner belt assembly to overlap the protruding parts of the rear seat adjuster.

  6. INSTALL REAR SEAT CENTER ARMREST ASSEMBLY (w/ Center Seat)


    1. A01GJRU

      Connect the 2 connectors.

    2. Install the rear seat center armrest assembly with the 2 bolts and nut.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

      Note

      Be careful not to damage the vehicle body.

    3. A01GLDME03

      Attach the hook to the center seatback frame wire.

    4. Attach the 2 clips to install the rear seat armrest hole board.

    5. A01GIIY

      While pressing the button, lower the rear center seat headrest assembly.

    6. Raise the rear seat center armrest assembly.

  7. INSTALL REAR SEATBACK ASSEMBLY LH

    A01GKZ2E01

    1. Connect the rear seatback assembly LH to the rear No. 2 seatback adjuster assembly, and press down on the rear seatback assembly LH to install it to the rear No. 2 seatback adjuster assembly. Then connect the air duct to the vehicle body.

      Note

      Be careful not to damage the vehicle body.

    2. Install the rear seatback assembly LH to the rear No. 2 seatback adjuster assembly with the 2 nuts.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

    3. Install the clip and attach the 3 pieces of fastening tape.

      Text in Illustration
      *1 Fastening Tape
    4. A01GL9B

      Connect the 3 connectors and attach the 7 wire harness clamps.

    5. A01GN8I

      Connect the 2 connectors.

    6. Install the junction block with the bolt.

      Torque:
      30 N*m  { 306 kgf*cm, 22 ft.*lbf }
    7. A01GMP8

      Connect the rear seat 3 point type belt assembly LH to the rear seat shoulder belt guide LH.

    8. Attach the 2 claws to close the 2 caps.

    9. A01GKCQE03
      Text in Illustration
      *1 Protruding Part

      Connect the anchor part of the rear seat 3 point type belt assembly LH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear seat 3 point type belt assembly to overlap protruding parts of the floor panel.

  8. INSTALL REAR SEATBACK ASSEMBLY RH

    A01GM7AE01

    1. Connect the rear seatback assembly RH to the rear No. 2 seat adjuster assembly, and press down on the rear seatback assembly RH to install it to the rear No. 2 seat adjuster assembly. Then connect the air duct to the vehicle body.

      Note

      Be careful not to damage the vehicle body.

    2. Install the rear seatback assembly RH to the rear No. 2 seat adjuster assembly with the 2 nuts.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

    3. Attach the clip and 3 pieces of fastening tape.

    4. Attach the 2 claws to connect the air hose.

      Text in Illustration
      *1 Air Hose
      *2 Fastening Tape
      *3 Air Duct

    5. Install the nut.

    6. A01GLLP

      Connect the 3 connectors and attach the 6 wire harness clamps.

    7. A01GI1Y

      Connect the 3 connectors.

    8. Install the junction block with the bolt.

      Torque:
      30 N*m  { 306 kgf*cm, 22 ft.*lbf }
    9. A01GI77

      Install the rear seat 3 point type belt assembly RH to the rear seat shoulder belt guide RH.

    10. Attach the 2 claws to close the 2 caps.

    11. A01GJ62E02
      Text in Illustration
      *1 Protruding Part

      Connect the anchor part of the rear seat 3 point type belt assembly RH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear seat 3 point type belt assembly RH to overlap protruding parts of the floor panel.

  9. INSTALL REAR SEAT CONSOLE BOX (w/ Rear Console Box)

    Click here

  10. INSTALL REAR CENTER SEAT CUSHION ASSEMBLY (w/ Center Seat)


    1. A01GJWX

      Attach the rear hook of the center seat cushion assembly to the center seatback frame sub-assembly.

      Note

      Be careful not to damage the vehicle body.

    2. Attach the front hook of the rear center seat cushion assembly to the vehicle body.

  11. INSTALL REAR SEAT AIRBAG ASSEMBLY RH


    1. A01GLWP

      Install the rear seat airbag assembly RH with the 3 bolts.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

    2. Connect the connector and attach the wire harness clamp.

  12. INSTALL REAR SEAT CUSHION ASSEMBLY LH


    1. A01GIBQ

      Connect the connector.

    2. Attach the rear hook of the rear seat cushion assembly LH to the rear seatback frame assembly LH.

      Note

      Be careful not to damage the vehicle body.

    3. Attach the 2 front hooks of the rear seat cushion assembly LH to the rear No. 2 seat adjuster assembly.

  13. INSTALL REAR SEAT CUSHION ASSEMBLY RH


    1. Connect the cable to the negative (-) battery terminal.

    2. Operate the ottoman switch to move the ottoman to the return position.

    3. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    4. A01GMJ8E02
      Text in Illustration
      *1 Seat Cover Hook
      *2 Nut
      *3 Rear Seat Cushion Lock Hook
      *4 Rear Hook

      Connect the connector.

    5. Attach the rear hook of the rear seat cushion assembly RH to the rear seatback spring assembly RH.

      Note

      Be careful not to damage the vehicle body.

    6. Attach the 2 front hooks of the rear seat cushion assembly RH to the the rear No. 1 seat adjuster assembly.

    7. Connect the 2 rear seat cushion lock hooks.

    8. Connect the seat cushion ottoman part with the 2 nuts.

    9. Install the 2 seat cushion cover hooks.

  14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  15. INSTALL COWL TOP VENTILATOR LOUVER RH


    1. A01GM4S

      for LHD:

      Install the 6 clips and cowl top ventilator louver RH.

      Note

      If the cowl top ventilator louver RH is not properly installed, water may leak into the engine room and cause malfunctions. Therefore, make sure the cowl top ventilator louver RH is installed properly.

    2. A01GI9P

      for RHD:

      Install the 6 clips and cowl top ventilator louver LH.

      Note

      If the cowl top ventilator louver LH is not properly installed, water may leak into the engine room and cause malfunctions. Therefore, make sure the cowl top ventilator louver LH is installed properly.

  16. CHECK SRS WARNING LIGHT

    Click here

  17. CHECK REAR SEAT ASSEMBLY


    1. Check the power seat operation:

      Click here

    2. Check the climate control seat system:

      Click here

    3. Check the seat vibration system:

      Click here

  18. CHECK REAR SUNSHADE SYSTEM (w/ Center Seat)

    Click here

  19. CHECK REAR DOOR SUNSHADE SYSTEM (w/ Center Seat)

    Click here