POWER MIRROR CONTROL SYSTEM Power Mirrors do not Return to Memorized Position

SYSTEM DESCRIPTION

When the seat memory M1, M2 or M3 switch is pressed, the front power seat switch (for driver side) memory's driver and passenger seat mirror position signal is sent through the CAN communication line to the front door ECU LH and RH. The front door ECU LH and RH then activate the mirror control motors to move the mirrors to the previously recorded positions.

WIRING DIAGRAM

A01GLM5E01

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK DTC


    1. Use the intelligent tester to check if the CAN communication system is functioning normally.

      Result:
      Result Proceed to
      CAN DTC is not output A
      CAN DTC is output (for LHD) B
      CAN DTC is output (for RHD) C

    B

    GO TO CAN COMMUNICATION SYSTEM Click here

    C

    GO TO CAN COMMUNICATION SYSTEM Click here

    A

  2. CHECK POWER MIRROR CONTROL FUNCTION


    1. Check that the mirror surface positions of the outer rear view mirror LH and RH can be moved using the outer mirror switch.

      OK
      Mirror surface positions of the outer rear view mirror LH and RH can be moved using the outer mirror switch.

    NG

    REPLACE OUTER MIRROR SWITCH ASSEMBLY Click here

    OK

  3. CHECK SEAT MEMORY SWITCH FUNCTION (MIRROR MEMORY FUNCTION)


    1. Check that the outer rear view mirror LH and RH positions can be memorized using the seat memory switch.

      OK
      Outer rear view mirror LH and RH positions can be memorized using seat memory switch.

    NG

    GO TO FRONT POWER SEAT CONTROL SYSTEM Click here

    OK

  4. READ VALUE USING INTELLIGENT TESTER (MIRROR POSITION SENSOR)


    1. Check the Data List for proper functioning of the mirror position sensor.

      Driver Door
      Tester Display Measurement Item/Display Normal Condition Diagnostic Note
      Mirror Vertical Sensor voltage Mirror vertical sensor voltage / MIN: 0, MAX: 255 Within range from 0 to 255 -
      Mirror Horizontal Sensor Voltage Mirror horizontal sensor voltage / MIN: 0, MAX: 255 Within range from 0 to 255 -
      Passenger Door
      Tester Display Measurement Item/Display Normal Condition Diagnostic Note
      Mirror Vertical Sensor voltage Mirror vertical sensor voltage / MIN: 0, MAX: 255 Within range from 0 to 255 -
      Mirror Horizontal Sensor Voltage Mirror horizontal sensor voltage / MIN: 0, MAX: 255 Within range from 0 to 255 -
      OK
      The value is changed by manual operation.
      Result
      Result Proceed to
      NG (for driver side) A
      OK (for driver side) B
      NG (for passenger side) C
      OK (for passenger side) D

    B

    REPLACE FRONT DOOR ECU (for Driver Side) Click here

    C

    CHECK FRONT DOOR ECU (for Passenger Side) Click here

    D

    REPLACE FRONT DOOR ECU (for Passenger Side) Click here

    A

  5. CHECK FRONT DOOR ECU (for Driver Side)


    1. A01GKBKE01

      for LHD:


      1. Measure the voltage according to the value in the table below.

        Standard voltage
        Tester Connection Switch Condition Specified Condition
        z10-5 (RVC) - z10-14 (RE1) Engine switch on (IG) 3.5 to 5.5 V

      2. Measure the resistance according to the value in the table below.

        Standard resistance
        Tester Connection Condition Specified Condition
        z10-14 (RE1) - Body ground Always Below 1 Ω
    2. A01GKBKE02

      for RHD:


      1. Measure the voltage according to the values in the table below.

        Standard voltage
        Tester Connection Switch Condition Specified Condition
        z9-5 (RVC) - z9-14 (RE1) Engine switch on (IG) 3.5 to 5.5 V

      2. Measure the resistance according to the value in the table below.

        Standard resistance
        Tester Connection Condition Specified Condition
        z9-14 (RE1) - Body ground Always Below 1 Ω

    NG

    REPLACE FRONT DOOR ECU (for Driver Side) Click here

    OK

    REPLACE OUTER MIRROR ACTUATOR ASSEMBLY (for Driver Side) Click here

  6. CHECK FRONT DOOR ECU (for Passenger Side)


    1. A01GKBKE02

      for LHD:


      1. Measure the voltage according to the values in the table below.

        Standard voltage
        Tester Connection Switch Condition Specified Condition
        z9-5 (RVC) - z9-14 (RE1) Engine switch on (IG) 3.5 to 5.5 V

      2. Measure the resistance according to the value in the table below.

        Standard resistance
        Tester Connection Condition Specified Condition
        z9-14 (RE1) - Body ground Always Below 1 Ω
    2. A01GKBKE01

      for RHD:


      1. Measure the voltage according to the value in the table below.

        Standard voltage
        Tester Connection Switch Condition Specified Condition
        z10-5 (RVC) - z10-14 (RE1) Engine switch on (IG) 3.5 to 5.5 V

      2. Measure the resistance according to the value in the table below.

        Standard resistance
        Tester Connection Condition Specified Condition
        z10-14 (RE1) - Body ground Always Below 1 Ω

    NG

    REPLACE FRONT DOOR ECU (for Passenger Side) Click here

    OK

    REPLACE OUTER MIRROR ACTUATOR ASSEMBLY (for Passenger Side) Click here