POWER MIRROR CONTROL SYSTEM Power Retractable Mirrors do not Operate with Power Retract Mirror Switch

SYSTEM DESCRIPTION

This circuit detects the conditions of the mirror retract switch.

The outer mirror switch sends information about the operating condition of the mirror retract switch (switch input signals) through the CAN communication line. Then the switch input signals are sent to the front door ECU LH and RH.

WIRING DIAGRAM

INSPECTION PROCEDURE

PROCEDURE

1. CHECK DTC

   
   

   1. Use the intelligent tester to check if the CAN communication system is functioning normally.

      Result:

      Result	Proceed to
      CAN DTC is not output	A
      CAN DTC is output (for LHD)	B
      CAN DTC is output (for RHD)	C

   
   

   B

   GO TO CAN COMMUNICATION SYSTEM Click here

   C

   GO TO CAN COMMUNICATION SYSTEM Click here

   A

2. READ VALUE USING INTELLIGENT TESTER (MIRROR RETRACT SWITCH)

   
   

   1. Check the Data List for proper functioning of the mirror retract switch.

      D-SEAT SW:

      Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
      Mirror Close Switch	Mirror retract switch signal / ON or OFF	ON: Mirror retract switch is ON (retracting) OFF: Mirror retract switch is OFF	-
      Mirror Open Switch	Mirror retract switch signal / ON or OFF	ON: Mirror retract switch is ON (returning) OFF: Mirror retract switch is OFF	-

      OK
      On tester screen, each item changes between ON and OFF according to above chart.

   
   

   NG

   REPLACE OUTER MIRROR SWITCH ASSEMBLY Click here

   OK

3. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MIRROR RETRACT FUNCTION)

   
   

   1. Select the Active Test, use the intelligent tester to generate a control command, and then check the mirror retract function.

      Driver Door

      Tester Display	Test Part	Control Range
      Mirr Fold / Retrn	Mirror retract operation	FOLD / RETURN

      Passenger Door

      Tester Display	Test Part	Control Range
      Mirr Fold / Retrn	Mirror retract operation	FOLD / RETURN

      Result (for driver side):

      Result	Proceed to
      Outer rear view mirror (for driver side) does not operate normally	A
      Outer rear view mirror (for driver side) operates normally	B

      Result (for passenger side):

      Result	Proceed to
      Outer rear view mirror (for passenger side) does not operate normally	C
      Outer rear view mirror (for passenger side) operates normally	D

   
   

   B

   REPLACE OUTER MIRROR SWITCH ASSEMBLY Click here

   C

   INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (for Passenger Side) Click here

   D

   REPLACE OUTER MIRROR SWITCH ASSEMBLY Click here

   A

4. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (for Driver Side)

   
   

   1. 

      for LHD:

      
      

      1. For each mirror position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

         Note

         
         

         • Disconnect and reconnect the battery once between each mirror position check.

         • The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

         OK

         Measurement Condition Mirror Position Specified Condition Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Forward position (A) Moves from (A) to retracted position (E) Battery positive (+) → Terminal 11 (MF) Battery negative (-) → Terminal 3 (MR) Forward position (A) Does not move Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Position between forward position (A) and driving position (C) Moves from (B) to retracted position (E) Battery positive (+) → Terminal 11 (MF) Battery negative (-) → Terminal 3 (MR) Position between forward position (A) and driving position (C) Moves from (B) to forward position (A) Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Driving position (C) Moves from (C) to retracted position (E) Battery positive (+) → Terminal 11 (MF) Battery negative (-) → Terminal 3 (MR) Driving position (C) Does not move Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Position between driving position (C) and retracted position (E) Moves from (D) to retracted position (E) Battery positive (+) → Terminal 11 (MF) Battery negative (-) → Terminal 3 (MR) Position between driving position (C) and retracted position (E) Moves from (D) to driving position (C) Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Retracted position (E) Does not move Battery positive (+) → Terminal 11 (MF) Battery negative (-) → Terminal 3 (MR) Retracted position (E) Moves from (E) to driving position (C)

   2. 

      for RHD:

      
      

      1. For each mirror position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

         Note

         
         

         • Disconnect and reconnect the battery once between each mirror position check.

         • The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

         OK

         Measurement Condition Mirror Position Specified Condition Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Forward position (A) Moves from (A) to retracted position (E) Battery positive (+) → Terminal 11 (MF) Battery negative (-) → Terminal 3 (MR) Forward position (A) Does not move Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Position between forward position (A) and driving position (C) Moves from (B) to retracted position (E) Battery positive (+) → Terminal 11 (MF) Battery negative (-) → Terminal 3 (MR) Position between forward position (A) and driving position (C) Moves from (B) to forward position (A) Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Driving position (C) Moves from (C) to retracted position (E) Battery positive (+) → Terminal 11 (MF) Battery negative (-) → Terminal 3 (MR) Driving position (C) Does not move Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Position between driving position (C) and retracted position (E) Moves from (D) to retracted position (E) Battery positive (+) → Terminal 11 (MF) Battery negative (-) → Terminal 3 (MR) Position between driving position (C) and retracted position (E) Moves from (D) to driving position (C) Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Retracted position (E) Does not move Battery positive (+) → Terminal 11 (MF) Battery negative (-) → Terminal 3 (MR) Retracted position (E) Moves from (E) to driving position (C)

   
   

   NG

   REPLACE OUTER MIRROR ACTUATOR ASSEMBLY (for Driver Side) Click here

   OK

   REPLACE FRONT DOOR ECU (for Driver Side) Click here

5. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (for Passenger Side)

   

   
   

   1. for LHD:

      
      

      1. For each mirror position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

         Note

         
         

         • Disconnect and reconnect the battery once between each mirror position check.

         • The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

         OK

         Measurement Condition Mirror Position Specified Condition Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Forward position (A) Moves from (A) to retracted position (E) Battery positive (+) → Terminal 11 (MF) Battery negative (-) → Terminal 3 (MR) Forward position (A) Does not move Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Position between forward position (A) and driving position (C) Moves from (B) to retracted position (E) Battery positive (+) → Terminal 11 (MF) Battery negative (-) → Terminal 3 (MR) Position between forward position (A) and driving position (C) Moves from (B) to forward position (A) Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Driving position (C) Moves from (C) to retracted position (E) Battery positive (+) → Terminal 11 (MF) Battery negative (-) → Terminal 3 (MR) Driving position (C) Does not move Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Position between driving position (C) and retracted position (E) Moves from (D) to retracted position (E) Battery positive (+) → Terminal 11 (MF) Battery negative (-) → Terminal 3 (MR) Position between driving position (C) and retracted position (E) Moves from (D) to driving position (C) Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Retracted position (E) Does not move Battery positive (+) → Terminal 11 (MF) Battery negative (-) → Terminal 3 (MR) Retracted position (E) Moves from (E) to driving position (C)

   2. 

      for RHD:

      
      

      1. For each mirror position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

         Note

         
         

         • Disconnect and reconnect the battery once between each mirror position check.

         • The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

         OK

         Measurement Condition Mirror Position Specified Condition Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Forward position (A) Moves from (A) to retracted position (E) Battery positive (+) → Terminal 11 (MF) Battery negative (-) → Terminal 3 (MR) Forward position (A) Does not move Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Position between forward position (A) and driving position (C) Moves from (B) to retracted position (E) Battery positive (+) → Terminal 11 (MF) Battery negative (-) → Terminal 3 (MR) Position between forward position (A) and driving position (C) Moves from (B) to forward position (A) Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Driving position (C) Moves from (C) to retracted position (E) Battery positive (+) → Terminal 11 (MF) Battery negative (-) → Terminal 3 (MR) Driving position (C) Does not move Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Position between driving position (C) and retracted position (E) Moves from (D) to retracted position (E) Battery positive (+) → Terminal 11 (MF) Battery negative (-) → Terminal 3 (MR) Position between driving position (C) and retracted position (E) Moves from (D) to driving position (C) Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Retracted position (E) Does not move Battery positive (+) → Terminal 11 (MF) Battery negative (-) → Terminal 3 (MR) Retracted position (E) Moves from (E) to driving position (C)

   
   

   NG

   REPLACE OUTER MIRROR ACTUATOR ASSEMBLY (for Passenger Side) Click here

   OK

   REPLACE FRONT DOOR ECU (for Passenger Side) Click here