POWER WINDOW CONTROL SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the intelligent tester to read the Data List allows values or status of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn on the intelligent tester.

    4. Enter the following menus.


      1. Select: Body / (desired system) / Data List /

    5. According to the display on tester, read the "Data List".

      Master Switch:
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      D Door P/W Auto SW Driver side power window auto UP/DOWN switch signal / ON or OFF

      ON: Driver side power window auto UP/DOWN switch on master switch operated

      OFF: Driver side power window switch on master switch not operated

      		 -
      P Door P/W Auto SW Front passenger side power window remote auto UP/DOWN switch signal / ON or OFF

      ON: Front passenger side power window remote auto UP/DOWN switch on master switch operated

      OFF: Front passenger side power window switch on master switch not operated

      		 -
      RR Door P/W Auto SW Rear power window RH remote auto UP/DOWN switch signal / ON or OFF

      ON: Rear power window RH remote auto UP/DOWN switch on master switch operated

      OFF: Rear power window RH switch on master switch not operated

      		 -
      RL Door P/W Auto SW Rear power window LH remote auto UP/DOWN switch signal / ON or OFF

      ON: Rear power window LH remote auto UP/DOWN switch on master switch operated

      OFF: Rear power window LH switch on master switch not operated

      		 -
      P Door P/W Up SW Front passenger side power window remote manual UP switch signal / ON or OFF

      ON: Front passenger side power window remote manual UP switch on master switch operated

      OFF: Front passenger side power window switch on master switch not operated

      		 -
      RR Door P/W Up Switch Rear power window RH remote manual UP switch signal / ON or OFF

      ON: Rear power window RH remote manual UP switch on master switch operated

      OFF: Rear power window RH switch on master switch not operated

      		 -
      RL Door P/W Up Switch Rear power window LH remote manual UP switch signal / ON or OFF

      ON: Rear power window LH remote manual UP switch on master switch operated

      OFF: Rear power window LH switch on master switch not operated

      		 -
      P Door P/W Down SW Front passenger side power window remote manual DOWN switch signal / ON or OFF

      ON: Front passenger side power window remote manual DOWN switch on master switch operated

      OFF: Front passenger side power window switch on master switch not operated

      		 -
      RR Door P/W Down SW Rear power window RH remote manual DOWN switch signal / ON or OFF

      ON: Rear power window RH remote manual DOWN switch on master switch operated

      OFF: Rear power window RH switch on master switch not operated

      		 -
      RL Door P/W Down SW Rear power window LH remote manual DOWN switch signal / ON or OFF

      ON: Rear power window LH remote manual DOWN switch on master switch operated

      OFF: Rear power window LH switch on master switch not operated

      		 -
      Window Lock Switch Status Power window LOCK switch / ON or OFF

      ON: Power window lock switch LOCK position

      OFF: Power window lock switch UNLOCK position

      		 -
      D-Door Motor:
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      D Door P/W Auto SW Driver side power window auto UP/DOWN switch signal / ON or OFF

      ON: Driver side power window auto UP/DOWN switch on master switch operated

      OFF: Driver side power window switch on master switch not operated

      		 -
      D Door P/W Up SW Driver side power window MANUAL UP switch signal / ON or OFF

      ON: Driver side power window manual UP switch on master switch operated

      OFF: Driver side power window switch on master switch not operated

      		 -
      D Door P/W Down SW Driver side power window MANUAL DOWN switch signal / ON or OFF

      ON: Driver side power window manual DOWN switch on master switch operated

      OFF: Driver side power window switch on master switch not operated

      		 -
      Glass Position (Close-1/4) Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open position / OK or Caution

      OK: Margin is sufficient during manual UP operation

      Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.

      		 -
      Glass Position (1/4-2/4) Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open position / OK or Caution

      OK: Margin is sufficient during manual UP operation

      Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.

      		 -
      Glass Position (2/4-3/4) Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open position / OK or Caution

      OK: Margin is sufficient during manual UP operation

      Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.

      		 -
      Glass Position (3/4-Open) Margin for jam protection triggering force of window glass within range of 3/4 to fully open position / OK or Caution

      OK: Margin is sufficient during manual UP operation

      Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.

      		 -
      P-Door Motor:
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      P Door P/W Auto SW Front passenger side power window remote auto UP/DOWN switch signal / ON or OFF

      ON: Front passenger side power window remote auto UP/DOWN switch on master switch operated

      OFF: Front passenger side power window switch on master switch not operated

      		 -
      P Door P/W Up SW Front passenger side power window remote manual UP switch signal / ON or OFF

      ON: Front passenger side power window remote manual UP switch on master switch operated

      OFF: Front passenger side power window switch on master switch not operated

      		 -
      P Door P/W Down SW Front passenger side power window remote manual DOWN switch signal / ON or OFF

      ON: Front passenger side power window remote manual DOWN switch on master switch operated

      OFF: Front passenger side power window switch on master switch not operated

      		 -
      Glass Position (Close-1/4) Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open position / OK or Caution

      OK: Margin is sufficient during manual UP operation

      Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.

      		 -
      Glass Position (1/4-2/4) Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open position / OK or Caution

      OK: Margin is sufficient during manual UP operation

      Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.

      		 -
      Glass Position (2/4-3/4) Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open position / OK or Caution

      OK: Margin is sufficient during manual UP operation

      Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.

      		 -
      Glass Position (3/4-Open) Margin for jam protection triggering force of window glass within range of 3/4 to fully open position / OK or Caution

      OK: Margin is sufficient during manual UP operation

      Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.

      		 -
      RL-Door Motor:
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      RL Door P/W Auto SW Rear power window LH remote auto UP/DOWN switch signal / ON or OFF

      ON: Rear power window LH remote auto UP/DOWN switch on master switch operated

      OFF: Rear power window LH switch on master switch not operated

      		 -
      RL Door P/W Up SW Rear power window LH remote manual UP switch signal / ON or OFF

      ON: Rear power window LH remote manual UP switch on master switch operated

      OFF: Rear power window LH switch on master switch not operated

      		 -
      RL Door P/W Down SW Rear power window LH remote manual DOWN switch signal / ON or OFF

      ON: Rear power window LH remote manual DOWN switch on master switch operated

      OFF: Rear power window LH switch on master switch not operated

      		 -
      Glass Position (Close-1/4) Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open position / OK or Caution

      OK: Margin is sufficient during manual UP operation

      Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.

      		 -
      Glass Position (1/4-2/4) Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open position / OK or Caution

      OK: Margin is sufficient during manual UP operation

      Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.

      		 -
      Glass Position (2/4-3/4) Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open position / OK or Caution

      OK: Margin is sufficient during manual UP operation

      Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.

      		 -
      Glass Position (3/4-Open) Margin for jam protection triggering force of window glass within range of 3/4 to fully open position / OK or Caution

      OK: Margin is sufficient during manual UP operation

      Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.

      		 -
      RR-Door Motor:
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      RR Door P/W Auto SW Rear power window RH remote auto UP/DOWN switch signal / ON or OFF

      ON: Rear power window RH remote auto UP/DOWN switch on master switch operated

      OFF: Rear power window RH switch on master switch not operated

      		 -
      RR Door P/W Up SW Rear power window RH remote manual UP switch signal / ON or OFF

      ON: Rear power window RH remote manual UP switch on master switch operated

      OFF: Rear power window RH switch on master switch not operated

      		 -
      RR Door P/W Down SW Rear power window RH remote manual DOWN switch signal / ON or OFF

      ON: Rear power window RH remote manual DOWN switch on master switch operated

      OFF: Rear power window RH switch on master switch not operated

      		 -
      Glass Position (Close-1/4) Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open position / OK or Caution

      OK: Margin is sufficient during manual UP operation

      Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.

      		 -
      Glass Position (1/4-2/4) Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open position / OK or Caution

      OK: Margin is sufficient during manual UP operation

      Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.

      		 -
      Glass Position (2/4-3/4) Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open position / OK or Caution

      OK: Margin is sufficient during manual UP operation

      Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.

      		 -
      Glass Position (3/4-Open) Margin for jam protection triggering force of window glass within range of 3/4 to fully open position / OK or Caution

      OK: Margin is sufficient during manual UP operation

      Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position.

      		 -
      Main Body:
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Communication D-Door Motor Connection status between power window regulator motor (for driver side) and main body ECU / OK or STOP

      OK: Connection

      Stop: No connection

      		 -
      Communication P-Door Motor Connection status between power window regulator motor (for front passenger side) and main body ECU / OK or STOP

      OK: Connection

      Stop: No connection

      		 -
      Communication RR-Door Motor Connection status between power window regulator motor (for rear RH) and main body ECU / OK or STOP

      OK: Connection

      Stop: No connection

      		 -
      Communication RL-Door Motor Connection status between power window regulator motor (for rear LH) and main body ECU / OK or STOP

      OK: Connection

      Stop: No connection

      		 -
      Communication Master SW Connection status between master switch and main body ECU / OK or STOP

      OK: Connection

      Stop: No connection

      		 -
      D Door Courtesy SW Driver side door courtesy switch signal / ON or OFF

      ON: Driver door open

      OFF: Driver door closed

      		 -
      P Door Courtesy SW Front passenger side door courtesy switch signal / ON or OFF

      ON: Front passenger door open

      OFF: Front passenger door closed

      		 -
      RL Door Courtesy SW Rear RH side door courtesy switch signal / ON or OFF

      ON: Rear RH side door open

      OFF: Rear RH side door closed

      		 -
      RR Door Courtesy SW Rear LH side door courtesy switch signal / ON or OFF

      ON: Rear LH side door open

      OFF: Rear LH side door closed

      		 -

  2. ACTIVE TEST

    Tech Tips

    Using the intelligent tester to perform Active Test allows relays, VSVs, actuators and parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Test early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Test.


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn on the intelligent tester.

    4. Enter the following menus.


      1. Select: Body / (desired system) / Active Test /

    5. According to the display on tester, perform the "Active Test".

      CAUTION:

      Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function does not operate.

      D-Door Motor:
      Tester Display Test Part Control Range
      Power Window Driver side power window UP or OFF (OFF)
      Power Window Driver side power window DOWN or OFF (OFF)
      P-Door Motor:
      Tester Display Test Part Control Range
      Power Window Front passenger side power window UP or OFF (OFF)
      Power Window Front passenger side power window DOWN or OFF (OFF)
      RL-Door Motor:
      Tester Display Test Part Control Range
      Power Window Rear LH side power window UP or OFF (OFF)
      Power Window Rear LH side power window DOWN or OFF (OFF)
      RR-Door Motor:
      Tester Display Test Part Control Range
      Power Window Rear RH side power window UP or OFF (OFF)
      Power Window Rear RH side power window DOWN or OFF (OFF)