AUDIO AND VISUAL SYSTEM, Diagnostic DTC:B15C3

DTC Code DTC Name
B15C3 Speaker Output Short

DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
B15C3 A short is detected in the speaker output circuit.

  • Stereo component amplifier assembly

  • DCM (telematics transceiver)*

  • Speakers

  • Harness or connector

WIRING DIAGRAM

A01GKYYE02
A01GK4XE04
A01GNGNE04

INSPECTION PROCEDURE

Tech Tips

After the inspection is completed, clear the DTCs.

PROCEDURE


  1. CLEAR DTC


    1. Clear the DTC Click here.


    NEXT

  2. CHECK FOR DTC


    1. Recheck for DTCs and check if the same DTC is output again Click here.

      OK
      No DTC is output.

    NG

    CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - SPEAKERS AND DCM [TELEMATICS TRANSCEIVER]) Click here

    OK

    USE SIMULATION METHOD TO CHECK Click here

  3. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - SPEAKERS AND DCM [TELEMATICS TRANSCEIVER])


    • *1: for RH Side

    • *2: for LH Side

    • *3: for 10 Speakers

    • *4: for 19 Speakers

    • *5: w/ Emergency Call Switch

    • *6: w/o Emergency Call Switch


    1. Disconnect the R86 and R85 stereo component amplifier assembly connectors.

    2. Disconnect the N4*1 and/or N12*2 front No. 1 speaker assembly connector.

    3. Disconnect the L84*1 and/or L9*2 front No. 2 speaker assembly connector.

    4. Disconnect the M1 front No. 3 speaker assembly connector.

    5. Disconnect the O10*1 and/or O21*2 rear No. 1 speaker assembly connector.

    6. Disconnect the Q3*1 and/or Q8*2 rear No. 3 speaker assembly connector.

    7. Disconnect the R20 floor stereo component speaker assembly connector.

    8. Disconnect the R18*1 and/or S18*2 rear header speaker assembly*4 connector.

    9. Disconnect the L142 DCM (telematics transceiver) connector.*5

    10. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for 10 Speakers
      Tester Connection Condition Specified Condition
      R85-5 (WFR+) - N4-1 Always Below 1 Ω
      R85-20 (WFR-) - N4-2 Always Below 1 Ω
      R85-4 (WFL+) - N12-1 Always Below 1 Ω
      R85-19 (WFL-) - N12-2 Always Below 1 Ω
      R85-13 (FR+) - L84-1 Always Below 1 Ω
      R85-28 (FR-) - L84-2 Always Below 1 Ω
      R85-12 (FL+) - L9-1 Always Below 1 Ω
      R85-27 (FL-) - L9-2 Always Below 1 Ω
      R85-7 (CTR+) - M1-1 Always Below 1 Ω
      R85-22 (CTR-) - M1-2 Always Below 1 Ω
      R85-15 (TWR+) - O10-1 Always Below 1 Ω
      R85-30 (TWR-) - O10-2 Always Below 1 Ω
      R85-14 (TWL+) - O21-1 Always Below 1 Ω
      R85-29 (TWL-) - O21-2 Always Below 1 Ω
      R85-6 (WF1+) - R20-1 (WF1+) Always Below 1 Ω
      R85-21 (WF1-) - R20-4 (WF1-) Always Below 1 Ω
      R85-5 (WFR+) - Body ground Always 10 kΩ or higher
      R85-20 (WFR-) - Body ground Always 10 kΩ or higher
      R85-4 (WFL+) - Body ground Always 10 kΩ or higher
      R85-19 (WFL-) - Body ground Always 10 kΩ or higher
      R85-13 (FR+) - Body ground Always 10 kΩ or higher
      R85-28 (FR-) - Body ground Always 10 kΩ or higher
      R85-12 (FL+) - Body ground Always 10 kΩ or higher
      R85-27 (FL-) - Body ground Always 10 kΩ or higher
      R85-7 (CTR+) - Body ground Always 10 kΩ or higher
      R85-22 (CTR-) - Body ground Always 10 kΩ or higher
      R85-15 (TWR+) - Body ground Always 10 kΩ or higher
      R85-30 (TWR-) - Body ground Always 10 kΩ or higher
      R85-14 (TWL+) - Body ground Always 10 kΩ or higher
      R85-29 (TWLL-) - Body ground Always 10 kΩ or higher
      R85-6 (WF1+) - Body ground Always 10 kΩ or higher
      R85-21 (WF1-) - Body ground Always 10 kΩ or higher
      for 19 Speakers
      Tester Connection Condition Specified Condition
      R85-2 (TMUT) - L142-9 (MUTE)*5 Always Below 1 Ω
      R85-5 (WFR+) - N4-1 Always Below 1 Ω
      R85-20 (WFR-) - N4-2 Always Below 1 Ω
      R85-4 (WFL+) - N12-1 Always Below 1 Ω
      R85-19 (WFL-) - N12-2 Always Below 1 Ω
      R85-13 (FR+) - L142-2 (SPI+)*5 Always Below 1 Ω
      R85-28 (FR-) - L142-3 (SPI-)*5 Always Below 1 Ω
      R85-13 (FR+) - L84-1*6 Always Below 1 Ω
      R85-28 (FR-) - L84-2*6 Always Below 1 Ω
      R85-12 (FL+) - L9-1 Always Below 1 Ω
      R85-27 (FL-) - L9-2 Always Below 1 Ω
      R85-7 (CTR+) - M1-1 Always Below 1 Ω
      R85-22 (CTR-) - M1-2 Always Below 1 Ω
      R86-4 (RR+) - O1-1 Always Below 1 Ω
      R86-10 (RR-) - O1-2 Always Below 1 Ω
      R86-3 (RL+) - O12-1 Always Below 1 Ω
      R86-9 (RL-) - O12-2 Always Below 1 Ω
      R85-15 (TWR+) - Q3-1 (+TW) Always Below 1 Ω
      R85-30 (TWR-) - Q3-2 (-TW) Always Below 1 Ω
      R85-14 (TWL+) - Q8-1 (+TW) Always Below 1 Ω
      R85-29 (TWL-) - Q8-2 (-TW) Always Below 1 Ω
      R85-6 (WF1+) - R20-1 (WF1+) Always Below 1 Ω
      R85-21 (WF1-) - R20-4 (WF1-) Always Below 1 Ω
      R86-2 (SR+) - R18-1 Always Below 1 Ω
      R86-6 (SR-) - R18-2 Always Below 1 Ω
      R86-1 (SL+) - S18-1 Always Below 1 Ω
      R86-5 (SL-) - S18-2 Always Below 1 Ω
      R85-2 (TMUT) - Body ground*5 Always 10 kΩ or higher
      R85-5 (WFR+) - Body ground Always 10 kΩ or higher
      R85-20 (WFR-) - Body ground Always 10 kΩ or higher
      R85-4 (WFL+) - Body ground Always 10 kΩ or higher
      R85-19 (WFL-) - Body ground Always 10 kΩ or higher
      R85-13 (FR+) - Body ground Always 10 kΩ or higher
      R85-28 (FR-) - Body ground Always 10 kΩ or higher
      R85-12 (FL+) - Body ground Always 10 kΩ or higher
      R85-27 (FL-) - Body ground Always 10 kΩ or higher
      R85-7 (CTR+) - Body ground Always 10 kΩ or higher
      R85-22 (CTR-) - Body ground Always 10 kΩ or higher
      R85-15 (TWR+) - Body ground Always 10 kΩ or higher
      R85-30 (TWR-) - Body ground Always 10 kΩ or higher
      R85-14 (TWL+) - Body ground Always 10 kΩ or higher
      R85-29 (TWL-) - Body ground Always 10 kΩ or higher
      R85-6 (WF1+) - Body ground Always 10 kΩ or higher
      R85-21 (WF1-) - Body ground Always 10 kΩ or higher
      R86-4 (RR+) - Body ground Always 10 kΩ or higher
      R86-10 (RR-) - Body ground Always 10 kΩ or higher
      R86-3 (RL+) - Body ground Always 10 kΩ or higher
      R86-9 (RL-) - Body ground Always 10 kΩ or higher
      R86-2 (SR+) - Body ground Always 10 kΩ or higher
      R86-6 (SR-) - Body ground Always 10 kΩ or higher
      R86-1 (SL+) - Body ground Always 10 kΩ or higher
      R86-5 (SL-) - Body ground Always 10 kΩ or higher
      Result
      Result Proceed to
      OK (w/ Emergency Call Switch) A
      OK (w/o Emergency Call Switch) B
      NG C

    B

    INSPECT FRONT NO. 2 SPEAKER ASSEMBLY Click here

    C

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    A

  4. CHECK HARNESS AND CONNECTOR (DCM [TELEMATICS TRANSCEIVER] - FRONT NO. 2 SPEAKER RH)


    1. Disconnect the L142 DCM (telematics transceiver) connector.

    2. Disconnect the L84 front No. 2 speaker assembly RH connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L142-11 (SPO+) - L84-1 Always Below 1 Ω
      L142-12 (SPO-) - L84-2 Always Below 1 Ω
      L142-11 (SPO+) - Body ground Always 10 kΩ or higher
      L142-12 (SPO-) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. INSPECT DCM (TELEMATICS TRANSCEIVER)


    1. A01GND6E15

      Remove the DCM (telematics transceiver) Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2 (SPI+) - 11 (SPO+) Always Below 1 Ω
      3 (SPI-) - 12 (SPO-) Always Below 1 Ω
      2 (SPI+) - Body ground Always 10 kΩ or higher
      3 (SPI-) - Body ground Always 10 kΩ or higher

    NG

    REPLACE DCM (TELEMATICS TRANSCEIVER) Click here

    OK

  6. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY


    1. Remove the front No. 2 speaker assembly Click here.

    2. Inspect the front No. 2 speaker assembly Click here.


    NG

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY Click here

    OK

  7. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY


    1. Remove the front No. 1 speaker assembly Click here.

    2. Inspect the front No. 1 speaker assembly Click here.


    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY Click here

    OK

  8. INSPECT FRONT NO. 3 SPEAKER ASSEMBLY


    1. Remove the front No. 3 speaker assembly Click here.

    2. Inspect the front No. 3 speaker assembly Click here.


    NG

    REPLACE FRONT NO. 3 SPEAKER ASSEMBLY Click here

    OK

  9. INSPECT FLOOR STEREO COMPONENT SPEAKER ASSEMBLY


    1. Remove the floor stereo component speaker assembly Click here.

    2. Inspect the floor stereo component speaker assembly Click here.

      Result
      Result Proceed to
      NG A
      OK (for 10 Speakers) B
      OK (for 19 Speakers) C

    B

    INSPECT REAR NO. 1 SPEAKER ASSEMBLY Click here

    C

    INSPECT REAR NO. 2 SPEAKER ASSEMBLY Click here

    A

    REPLACE FLOOR STEREO COMPONENT SPEAKER ASSEMBLY Click here

  10. INSPECT REAR NO. 1 SPEAKER ASSEMBLY


    1. Remove the rear No. 1 speaker assembly.


    2. Inspect the rear No. 1 speaker assembly.


      Result
      Result Proceed to
      OK A
      NG (for Standard Body) B
      NG (for Long Body) C

    B

    REPLACE REAR NO. 1 SPEAKER ASSEMBLY Click here

    C

    REPLACE REAR NO. 1 SPEAKER ASSEMBLY Click here

    A

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY Click here

  11. INSPECT REAR NO. 2 SPEAKER ASSEMBLY


    1. Remove the rear No. 2 speaker assembly.


    2. Inspect the rear No. 2 speaker assembly.


      Result
      Result Proceed to
      OK A
      NG (for Standard Body) B
      NG (for Long Body) C

    B

    REPLACE REAR NO. 2 SPEAKER ASSEMBLY Click here

    C

    REPLACE REAR NO. 2 SPEAKER ASSEMBLY Click here

    A

  12. INSPECT REAR NO. 1 SPEAKER ASSEMBLY


    1. Remove the rear No. 1 speaker assembly.


    2. Inspect the rear No. 1 speaker assembly.


      Result
      Result Proceed to
      OK A
      NG (for Standard Body) B
      NG (for Long Body) C

    B

    REPLACE REAR NO. 1 SPEAKER ASSEMBLY Click here

    C

    REPLACE REAR NO. 1 SPEAKER ASSEMBLY Click here

    A

  13. CHECK HARNESS AND CONNECTOR (REAR NO. 3 SPEAKER ASSEMBLY - REAR NO. 1 SPEAKER ASSEMBLY)


    • *1: for LH Side

    • *2: for RH Side


    1. Disconnect the Q8*1 or Q3*2 rear No. 3 speaker assembly connector.

    2. Disconnect the O21*1 or O10*2 rear No. 1 speaker assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LH Side
      Tester Connection Condition Specified Condition
      Q8-3 (RLD+) - O21-1 Always Below 1 Ω
      Q8-4 (RLD-) - O21-2 Always Below 1 Ω
      Q8-3 (RLD+) - Body ground Always 10 kΩ or higher
      Q8-4 (RLD-) - Body ground Always 10 kΩ or higher
      for RH Side
      Tester Connection Condition Specified Condition
      Q3-3 (RRD+) - O10-1 Always Below 1 Ω
      Q3-4 (RRD-) - O10-2 Always Below 1 Ω
      Q3-3 (RRD+) - Body ground Always 10 kΩ or higher
      Q3-4 (RRD-) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  14. REPLACE REAR NO. 3 SPEAKER ASSEMBLY


    1. Temporarily replace the rear No. 3 speaker assembly LH and/or RH with a new or normally functioning one.



    NEXT

  15. CLEAR DTC


    1. Clear the DTCs Click here.


    NEXT

  16. CHECK FOR DTC


    1. Recheck for DTCs and check if the same DTC is output again Click here.

      OK
      No DTCs is output

    NG

    INSPECT REAR HEADER SPEAKER ASSEMBLY Click here

    OK

    END (REAR NO. 3 SPEAKER ASSEMBLY IS DEFECTIVE)

  17. INSPECT REAR HEADER SPEAKER ASSEMBLY


    1. Remove the rear header speaker assembly Click here.

    2. Inspect the rear header speaker assembly Click here.


    NG

    REPLACE REAR HEADER SPEAKER ASSEMBLY Click here

    OK

    REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY Click here