REAR DOOR LOCK REMOVAL

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  2. REMOVE COWL TOP VENTILATOR LOUVER RH


    1. A01GM4S

      Remove the 6 clips and cowl top ventilator louver RH.

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG LH


    1. A01GM19

      Using a screwdriver, detach the 3 claws and remove the rear door inside handle bezel plug LH.

      Tech Tips

      Tape the screwdriver tip before use.

  5. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

    A01GJSWE01

    1. Apply protective tape to the area around the rear rear power window regulator switch assembly with rear door armrest base panel.

    2. Using a clip remover, detach the 2 clips in the order shown in the illustration.

      Text in Illustration
      *1 Protective Tape
    3. A01GKXL

      Disconnect the connector.

    4. Remove the screw and illumination light.

    5. Remove the rear rear power window regulator switch assembly with rear door armrest base panel.

  6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

    w/o Rear Door Sunshade:

    Click here

    w/ Rear Door Sunshade

    Click here

  7. REMOVE REAR DOOR TRIM COVER LH


    1. A01GNI7

      Remove the cushion.

    2. Using a clip remover, detach the 5 clips and remove the rear door trim cover LH.

  8. REMOVE REAR DOOR FRAME GARNISH LH


    1. A01GKIM

      w/o Rear Door Sunshade:


      1. Remove the screw and detach the clip.

      2. Detach the claws and remove the rear door frame garnish LH.

    2. A01GKBI

      w/ Rear Door Sunshade:


      1. Detach the 2 clips.

      2. Detach the claws and remove the rear door frame garnish LH.

  9. REMOVE REAR DOOR NO. 2 FRAME GARNISH LH


    1. A01GMBCE04
      Text in Illustration
      *A w/o Rear Door Sunshade
      *B w/ Rear Door Sunshade

      Detach the claws and remove the rear door No. 2 frame garnish LH.

  10. REMOVE REAR CURTAIN SUB-ASSEMBLY LH (w/ Rear Door Sunshade)


    1. A01GM0R

      for Standard Body:


      1. Remove the 10 screws.

      2. Detach the 3 clips and remove the rear curtain sub-assembly LH.

      3. Disconnect the connector

    2. A01GKVH

      for Long Body:


      1. Remove the 10 screws.

      2. Detach the 4 clips and remove the rear curtain sub-assembly LH.

      3. Disconnect the connector

  11. REMOVE NO. 1 AUTO CURTAIN RAIL BRACKET LH (w/ Rear Door Sunshade)


    1. A01GK25

      Using a clip remover, detach the clip and remove the No. 1 auto curtain rail bracket LH.

  12. REMOVE SIDE TRIM BOARD COVER REAR LH (w/ Rear Door Sunshade)


    1. A01GJMZ

      Remove the 2 screws and rear side trim board cover LH.

  13. REMOVE REAR INNER DOOR GLASS WEATHERSTRIP LH


    1. for Long Body:


      1. A01GNR8

        Remove the rear door glass inner weatherstrip LH by pulling it upward in the direction indicated by the arrow.

    2. for Standard Body:


      1. A01GK80

        Remove the rear door glass inner weatherstrip LH by pulling it upward in the direction indicated by the arrow.

  14. REMOVE REAR DOOR SERVICE HOLE COVER LH


    1. A01GLVD

      Remove the rear door service hole cover LH.

  15. REMOVE REAR DOOR DIVISION BAR BRACKET LOWER LH


    1. A01GINF

      Remove the 3 nuts and rear door division bar lower bracket LH.

  16. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH


    1. A01GKT1

      Remove the 2 nuts.

    2. Remove the rear door window division bar sub-assembly LH together with the rear door glass run LH.

  17. REMOVE REAR DOOR GLASS RUN LH


    1. Remove the front door glass run LH.

  18. REMOVE REAR DOOR QUARTER WINDOW GLASS LH


    1. A01GKG3

      Remove the rear door quarter window glass LH and rear door quarter window weatherstrip LH as a unit as shown in the illustration.

  19. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH


    1. Remove the hole plug.

    2. A01GNLC

      Remove the 2 bolts.

      Note

      Be careful when removing the bolts as the glass may fall and become damaged.

    3. Remove the rear door glass sub-assembly LH.

      Tech Tips

      Remove the glass upward.

      Note

      Be careful not to damage the glass.

  20. REMOVE REAR DOOR LOCK ASSEMBLY LH


    1. A01GHYLE01

      Disconnect the 2 connectors and detach the 2 clamps.

    2. Using a T30 'TORX' socket, remove the 3 screws labeled A and 2 screws labeled B.

    3. Remove the rear door lock assembly LH.

      Note

      Be careful when removing the bolts as the door lock may fall and become damaged.

      Tech Tips

      Remove the door lock through the service hole.

  21. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    1. A01GKGOE04
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the claw.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01GKQS

      Remove the rear door lock remote control cable assembly LH.

  22. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    1. A01GMEEE06

      Using a screwdriver, detach the 3 claws.

      Tech Tips

      Tape the screwdriver tip before use.

      Text in Illustration
      *1 Protective Tape
    2. A01GIP6

      Remove the rear door inside locking cable assembly LH.